upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
122 lines
3.6 KiB
122 lines
3.6 KiB
#
|
|
# Boot count configuration
|
|
#
|
|
|
|
menuconfig BOOTCOUNT_LIMIT
|
|
bool "Enable support for checking boot count limit"
|
|
help
|
|
Enable checking for exceeding the boot count limit.
|
|
More information: http://www.denx.de/wiki/DULG/UBootBootCountLimit
|
|
|
|
if BOOTCOUNT_LIMIT
|
|
|
|
choice
|
|
prompt "Boot count device"
|
|
default BOOTCOUNT_AM33XX if AM33XX || SOC_DA8XX
|
|
default BOOTCOUNT_AT91 if AT91SAM9XE
|
|
default BOOTCOUNT_GENERIC
|
|
|
|
config BOOTCOUNT_GENERIC
|
|
bool "Generic default boot counter"
|
|
help
|
|
Generic bootcount stored at SYS_BOOTCOUNT_ADDR.
|
|
|
|
SYS_BOOTCOUNT_ADDR:
|
|
Set to the address where the bootcount and bootcount magic
|
|
will be stored.
|
|
|
|
config BOOTCOUNT_EXT
|
|
bool "Boot counter on EXT filesystem"
|
|
help
|
|
Add support for maintaining boot count in a file on an EXT
|
|
filesystem.
|
|
|
|
config BOOTCOUNT_AM33XX
|
|
bool "Boot counter in AM33XX RTC IP block"
|
|
depends on AM33XX || SOC_DA8XX
|
|
select SPL_AM33XX_ENABLE_RTC32K_OSC if AM33XX
|
|
help
|
|
A bootcount driver for the RTC IP block found on many TI platforms.
|
|
This requires the RTC clocks, etc, to be enabled prior to use and
|
|
not all boards with this IP block on it will have the RTC in use.
|
|
|
|
config BOOTCOUNT_ENV
|
|
bool "Boot counter in environment"
|
|
help
|
|
If no softreset save registers are found on the hardware
|
|
"bootcount" is stored in the environment. To prevent a
|
|
saveenv on all reboots, the environment variable
|
|
"upgrade_available" is used. If "upgrade_available" is
|
|
0, "bootcount" is always 0, if "upgrade_available" is
|
|
1 "bootcount" is incremented in the environment.
|
|
So the Userspace Application must set the "upgrade_available"
|
|
and "bootcount" variable to 0, if a boot was successfully.
|
|
|
|
config BOOTCOUNT_RAM
|
|
bool "Boot counter in RAM"
|
|
help
|
|
Store the bootcount in DRAM protected against against bit errors
|
|
due to short power loss or holding a system in RESET.
|
|
|
|
config BOOTCOUNT_I2C
|
|
bool "Boot counter on I2C device"
|
|
help
|
|
Enable support for the bootcounter on an i2c (like RTC) device.
|
|
CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
|
|
CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
|
|
the bootcounter.
|
|
|
|
config BOOTCOUNT_AT91
|
|
bool "Boot counter for Atmel AT91SAM9XE"
|
|
depends on AT91SAM9XE
|
|
|
|
endchoice
|
|
|
|
config BOOTCOUNT_ALEN
|
|
int "I2C address length"
|
|
default 1
|
|
depends on BOOTCOUNT_I2C
|
|
help
|
|
Length of the the I2C address at SYS_BOOTCOUNT_ADDR for storing
|
|
the boot counter.
|
|
|
|
config SYS_BOOTCOUNT_SINGLEWORD
|
|
bool "Use single word to pack boot count and magic value"
|
|
depends on BOOTCOUNT_GENERIC
|
|
help
|
|
This option enables packing boot count magic value and boot count
|
|
into single word (32 bits).
|
|
|
|
config SYS_BOOTCOUNT_EXT_INTERFACE
|
|
string "Interface on which to find boot counter EXT filesystem"
|
|
default "mmc"
|
|
depends on BOOTCOUNT_EXT
|
|
help
|
|
Set the interface to use when locating the filesystem to use for the
|
|
boot counter.
|
|
|
|
config SYS_BOOTCOUNT_EXT_DEVPART
|
|
string "Partition of the boot counter EXT filesystem"
|
|
default "0:1"
|
|
depends on BOOTCOUNT_EXT
|
|
help
|
|
Set the partition to use when locating the filesystem to use for the
|
|
boot counter.
|
|
|
|
config SYS_BOOTCOUNT_EXT_NAME
|
|
string "Path and filename of the EXT filesystem based boot counter"
|
|
default "/boot/failures"
|
|
depends on BOOTCOUNT_EXT
|
|
help
|
|
Set the filename and path of the file used to store the boot counter.
|
|
|
|
config SYS_BOOTCOUNT_ADDR
|
|
hex "RAM address used for reading and writing the boot counter"
|
|
default 0x44E3E000 if BOOTCOUNT_AM33XX
|
|
default 0xE0115FF8 if ARCH_LS1043A || ARCH_LS1021A
|
|
depends on BOOTCOUNT_AM33XX || BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \
|
|
BOOTCOUNT_I2C
|
|
help
|
|
Set the address used for reading and writing the boot counter.
|
|
|
|
endif
|
|
|