upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/drivers/serial/mxs_auart.c

151 lines
3.9 KiB

/*
* Freescale i.MX23/i.MX28 AUART driver
*
* Copyright (C) 2013 Andreas Wass <andreas.wass@dalelven.com>
*
* Based on the MXC serial driver:
*
* (c) 2007 Sascha Hauer <s.hauer@pengutronix.de>
*
* Further based on the Linux mxs-auart.c driver:
*
* Freescale STMP37XX/STMP38X Application UART drkiver
* Copyright 2008-2010 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <serial.h>
#include <linux/compiler.h>
#include <asm/arch/regs-base.h>
#include <asm/arch/regs-uartapp.h>
#include <asm/arch/sys_proto.h>
DECLARE_GLOBAL_DATA_PTR;
#ifndef CONFIG_MXS_AUART_BASE
#error "CONFIG_MXS_AUART_BASE must be set to the base UART to use"
#endif
/* AUART clock always supplied by XTAL and always 24MHz */
#define MXS_AUART_CLK 24000000
static struct mxs_uartapp_regs *get_uartapp_registers(void)
{
return (struct mxs_uartapp_regs *)CONFIG_MXS_AUART_BASE;
}
/**
* Sets the baud rate and settings.
* The settings are: 8 data bits, no parit and 1 stop bit.
*/
static void mxs_auart_setbrg(void)
{
u32 div;
u32 linectrl = 0;
struct mxs_uartapp_regs *regs = get_uartapp_registers();
if (!gd->baudrate)
gd->baudrate = CONFIG_BAUDRATE;
/*
* From i.MX28 datasheet:
* div is calculated by calculating UARTCLK*32/baudrate, rounded to int
* div must be between 0xEC and 0x003FFFC0 inclusive
* Lowest 6 bits of div goes in BAUD_DIVFRAC part of LINECTRL register
* Next 16 bits goes in BAUD_DIVINT part of LINECTRL register
*/
div = (MXS_AUART_CLK * 32) / gd->baudrate;
if (div < 0xEC || div > 0x003FFFC0)
return;
linectrl |= ((div & UARTAPP_LINECTRL_EXTRACT_BAUD_DIVFRAC_MASK) <<
UARTAPP_LINECTRL_BAUD_DIVFRAC_OFFSET) &
UARTAPP_LINECTRL_BAUD_DIVFRAC_MASK;
linectrl |= ((div >> UARTAPP_LINECTRL_EXTRACT_BAUD_DIVINT_OFFSET) <<
UARTAPP_LINECTRL_BAUD_DIVINT_OFFSET) &
UARTAPP_LINECTRL_BAUD_DIVINT_MASK;
/* Word length: 8 bits */
linectrl |= UARTAPP_LINECTRL_WLEN_8BITS;
/* Enable FIFOs. */
linectrl |= UARTAPP_LINECTRL_FEN_MASK;
/* Write above settings, no parity, 1 stop bit */
writel(linectrl, &regs->hw_uartapp_linectrl);
}
static int mxs_auart_init(void)
{
struct mxs_uartapp_regs *regs = get_uartapp_registers();
/* Reset everything */
mxs_reset_block(&regs->hw_uartapp_ctrl0_reg);
/* Disable interrupts */
writel(0, &regs->hw_uartapp_intr);
/* Set baud rate and settings */
serial_setbrg();
/* Disable RTS and CTS, ignore LINECTRL2 register */
writel(UARTAPP_CTRL2_RTSEN_MASK |
UARTAPP_CTRL2_CTSEN_MASK |
UARTAPP_CTRL2_USE_LCR2_MASK,
&regs->hw_uartapp_ctrl2_clr);
/* Enable receiver, transmitter and UART */
writel(UARTAPP_CTRL2_RXE_MASK |
UARTAPP_CTRL2_TXE_MASK |
UARTAPP_CTRL2_UARTEN_MASK,
&regs->hw_uartapp_ctrl2_set);
return 0;
}
static void mxs_auart_putc(const char c)
{
struct mxs_uartapp_regs *regs = get_uartapp_registers();
/* Wait in loop while the transmit FIFO is full */
while (readl(&regs->hw_uartapp_stat) & UARTAPP_STAT_TXFF_MASK)
;
writel(c, &regs->hw_uartapp_data);
if (c == '\n')
mxs_auart_putc('\r');
}
static int mxs_auart_tstc(void)
{
struct mxs_uartapp_regs *regs = get_uartapp_registers();
/* Checks if receive FIFO is empty */
return !(readl(&regs->hw_uartapp_stat) & UARTAPP_STAT_RXFE_MASK);
}
static int mxs_auart_getc(void)
{
struct mxs_uartapp_regs *regs = get_uartapp_registers();
/* Wait until a character is available to read */
while (!mxs_auart_tstc())
;
/* Read the character from the data register */
return readl(&regs->hw_uartapp_data) & 0xFF;
}
static struct serial_device mxs_auart_drv = {
.name = "mxs_auart_serial",
.start = mxs_auart_init,
.stop = NULL,
.setbrg = mxs_auart_setbrg,
.putc = mxs_auart_putc,
.puts = default_serial_puts,
.getc = mxs_auart_getc,
.tstc = mxs_auart_tstc,
};
void mxs_auart_initialize(void)
{
serial_register(&mxs_auart_drv);
}
__weak struct serial_device *default_serial_console(void)
{
return &mxs_auart_drv;
}