upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
101 lines
2.2 KiB
101 lines
2.2 KiB
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
|
|
/*
|
|
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/ddr.h>
|
|
#include <power/pmic.h>
|
|
#include <power/stpmu1.h>
|
|
|
|
#ifdef CONFIG_DEBUG_UART_BOARD_INIT
|
|
void board_debug_uart_init(void)
|
|
{
|
|
#if (CONFIG_DEBUG_UART_BASE == STM32_UART4_BASE)
|
|
|
|
#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00)
|
|
#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28)
|
|
|
|
/* UART4 clock enable */
|
|
setbits_le32(RCC_MP_APB1ENSETR, BIT(16));
|
|
|
|
#define GPIOG_BASE 0x50008000
|
|
/* GPIOG clock enable */
|
|
writel(BIT(6), RCC_MP_AHB4ENSETR);
|
|
/* GPIO configuration for EVAL board
|
|
* => Uart4 TX = G11
|
|
*/
|
|
writel(0xffbfffff, GPIOG_BASE + 0x00);
|
|
writel(0x00006000, GPIOG_BASE + 0x24);
|
|
#else
|
|
|
|
#error("CONFIG_DEBUG_UART_BASE: not supported value")
|
|
|
|
#endif
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_PMIC_STPMU1
|
|
int board_ddr_power_init(void)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
|
|
ret = uclass_get_device_by_driver(UCLASS_PMIC,
|
|
DM_GET_DRIVER(pmic_stpmu1), &dev);
|
|
if (ret)
|
|
/* No PMIC on board */
|
|
return 0;
|
|
|
|
/* Set LDO3 to sync mode */
|
|
ret = pmic_reg_read(dev, STPMU1_LDOX_CTRL_REG(STPMU1_LDO3));
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret &= ~STPMU1_LDO3_MODE;
|
|
ret &= ~STPMU1_LDO12356_OUTPUT_MASK;
|
|
ret |= STPMU1_LDO3_DDR_SEL << STPMU1_LDO12356_OUTPUT_SHIFT;
|
|
|
|
ret = pmic_reg_write(dev, STPMU1_LDOX_CTRL_REG(STPMU1_LDO3),
|
|
ret);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Set BUCK2 to 1.35V */
|
|
ret = pmic_clrsetbits(dev,
|
|
STPMU1_BUCKX_CTRL_REG(STPMU1_BUCK2),
|
|
STPMU1_BUCK_OUTPUT_MASK,
|
|
STPMU1_BUCK2_1350000V);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Enable BUCK2 and VREF */
|
|
ret = pmic_clrsetbits(dev,
|
|
STPMU1_BUCKX_CTRL_REG(STPMU1_BUCK2),
|
|
STPMU1_BUCK_EN, STPMU1_BUCK_EN);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
mdelay(STPMU1_DEFAULT_START_UP_DELAY_MS);
|
|
|
|
ret = pmic_clrsetbits(dev, STPMU1_VREF_CTRL_REG,
|
|
STPMU1_VREF_EN, STPMU1_VREF_EN);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
mdelay(STPMU1_DEFAULT_START_UP_DELAY_MS);
|
|
|
|
/* Enable LDO3 */
|
|
ret = pmic_clrsetbits(dev,
|
|
STPMU1_LDOX_CTRL_REG(STPMU1_LDO3),
|
|
STPMU1_LDO_EN, STPMU1_LDO_EN);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
mdelay(STPMU1_DEFAULT_START_UP_DELAY_MS);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|