upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
256 lines
8.4 KiB
256 lines
8.4 KiB
/*
|
|
* (C) Copyright 2008
|
|
* Niklaus Giger, Netstal Maschinen AG, niklaus.giger@netstal.com
|
|
* adapted from amcc-common.h by
|
|
* (C) Copyright 2008
|
|
* * Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* Common configuration options for all Netstal boards
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
|
|
#ifndef __NETSTAL_COMMON_H
|
|
#define __NETSTAL_COMMON_H
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
|
|
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* Start of U-Boot */
|
|
#define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
|
|
|
|
/*
|
|
* UART
|
|
*/
|
|
#define CONFIG_SERIAL_MULTI
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
|
|
|
|
/*
|
|
* I2C
|
|
*/
|
|
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
|
|
#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
|
|
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F
|
|
|
|
/* This is the 7bit address of the device, not including P. */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
|
|
/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE
|
|
|
|
/*
|
|
* Ethernet/EMAC/PHY
|
|
*/
|
|
#define CONFIG_PPC4xx_EMAC
|
|
#define CONFIG_MII /* MII PHY management */
|
|
#define CONFIG_PHY_ADDR 1 /* PHY address */
|
|
#define CONFIG_NET_MULTI 1
|
|
#if defined(CONFIG_440)
|
|
#define CONFIG_NETCONSOLE /* include NetConsole support */
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 32 /* number of eth rx buffers */
|
|
#else
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 16 /* number of eth rx buffers */
|
|
#endif
|
|
#define CONFIG_HAS_ETH0
|
|
|
|
/*
|
|
* Commands
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_ASKENV
|
|
#if defined(CONFIG_440)
|
|
#define CONFIG_CMD_CACHE
|
|
#endif
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_DIAG
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_IRQ
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_NET
|
|
#define CONFIG_CMD_NFS
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_REGINFO
|
|
#define CONFIG_BOOT_RETRY_TIME 30
|
|
#define CONFIG_RESET_TO_RETRY
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CONFIG_SYS_EXTBDINFO /* To use extended board_into (bd_t) */
|
|
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
#define CONFIG_CMDLINE_EDITING /* add command line history */
|
|
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
|
|
#define CONFIG_LOOPW /* enable loopw command */
|
|
#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */
|
|
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
|
|
#define CONFIG_VERSION_VARIABLE /* include version env variable */
|
|
#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup*/
|
|
|
|
#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
|
|
#ifdef CONFIG_SYS_HUSH_PARSER
|
|
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
|
|
#endif
|
|
|
|
#define CONFIG_LOADS_ECHO /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*
|
|
* Internal Definitions
|
|
*/
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/
|
|
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
|
|
#endif
|
|
|
|
/*
|
|
* Pass open firmware flat tree
|
|
*/
|
|
#define CONFIG_OF_LIBFDT
|
|
#define CONFIG_OF_BOARD_SETUP
|
|
|
|
/*
|
|
* Booting and default environment
|
|
*/
|
|
#define CONFIG_PREBOOT "echo;" \
|
|
"echo Type \"run net_nfs\" to mount root filesystem over NFS;" \
|
|
"echo"
|
|
#define CONFIG_BOOTCOMMAND "run vx"
|
|
|
|
/*
|
|
* Only very few boards have default console not on ttyS0 (like Taishan)
|
|
*/
|
|
#if !defined(CONFIG_USE_TTY)
|
|
#define CONFIG_USE_TTY ttyS0
|
|
#endif
|
|
|
|
/*
|
|
* Only some 4xx PPC's are equipped with an FPU
|
|
*/
|
|
#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
|
|
defined(CONFIG_460EX) || defined(CONFIG_460GT)
|
|
#define CONFIG_NETSTAL_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
|
|
#else
|
|
#define CONFIG_NETSTAL_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
|
|
#endif
|
|
|
|
/*
|
|
* Only some boards need to extend the bootargs by some additional
|
|
* parameters (like Makalu)
|
|
*/
|
|
#if !defined(CONFIG_ADDMISC)
|
|
#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs}\0"
|
|
#endif
|
|
|
|
#define xstr(s) str(s)
|
|
#define str(s) #s
|
|
|
|
/* Setup some values for the default environment variables */
|
|
#define CONFIG_SERVERIP 172.25.1.1
|
|
#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */
|
|
#define CONFIG_OVERWRITE_ETHADDR_ONCE
|
|
|
|
#define CONFIG_SYS_TFTP_LOADADDR 0x01000000
|
|
#define CONFIG_SYS_VXWORKS_ADD_PARAMS "u=dpu pw=netstal8752"
|
|
#define CONFIG_SYS_VXWORKS_SERVERNAME "c"
|
|
/*
|
|
* General common environment variables shared by all boards produced by Netstal Maschinen
|
|
*/
|
|
#define CONFIG_NETSTAL_DEF_ENV \
|
|
"netdev=eth0\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"addip=setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
|
":${hostname}:${netdev}:off panic=1\0" \
|
|
"addtty=setenv bootargs ${bootargs}" \
|
|
" console=" xstr(CONFIG_USE_TTY) ",${baudrate}\0" \
|
|
CONFIG_ADDMISC \
|
|
"initrd_high=30000000\0" \
|
|
"kernel_addr_r=400000\0" \
|
|
"fdt_addr_r=800000\0" \
|
|
"hostname=" xstr(CONFIG_HOSTNAME) "\0" \
|
|
"bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \
|
|
"uload=tftp " xstr(CONFIG_SYS_TFTP_LOADADDR) " " \
|
|
xstr(CONFIG_HOSTNAME) "/u-boot.bin\0" \
|
|
"vx_rom=" xstr(CONFIG_HOSTNAME) "/" \
|
|
xstr(CONFIG_HOSTNAME) "_vx_rom\0" \
|
|
"update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) " FFFFFFFF;"\
|
|
"era " xstr(CONFIG_SYS_MONITOR_BASE) " FFFFFFFF;" \
|
|
"cp.b ${fileaddr} "xstr(CONFIG_SYS_MONITOR_BASE) \
|
|
" ${filesize}; setenv filesize\0" \
|
|
"upd=run uload update\0" \
|
|
"vx=setenv bootfile ${vx_rom}; tftp " \
|
|
xstr(CONFIG_SYS_TFTP_LOADADDR) "; bootvx\0" \
|
|
CONFIG_NETSTAL_DEF_ENV_ROOTPATH
|
|
|
|
/*
|
|
* Default environment for arch/powerpc booting
|
|
* for boards that are ported to arch/powerpc
|
|
*/
|
|
#define CONFIG_NETSTAL_DEF_ENV_POWERPC \
|
|
"flash_self=run ramargs addip addtty addmisc;" \
|
|
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
|
|
"flash_nfs=run nfsargs addip addtty addmisc;" \
|
|
"bootm ${kernel_addr} - ${fdt_addr}\0" \
|
|
"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
|
|
"tftp ${fdt_addr_r} ${fdt_file}; " \
|
|
"run nfsargs addip addtty addmisc;" \
|
|
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
|
|
"fdt_file=" xstr(CONFIG_HOSTNAME) "/" xstr(CONFIG_HOSTNAME) ".dtb\0"
|
|
|
|
#endif /* __NETSTAL_COMMON_H */
|
|
|