u-boot/board/phytec/pcm051/board.c

/*
 * board.c
 *
 * Board functions for Phytec phyCORE-AM335x (pcm051) based boards
 *
 * Copyright (C) 2013 Lemonage Software GmbH
 * Author Lars Poeschel <poeschel@lemonage.de>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <errno.h>
#include <spl.h>
#include <asm/arch/cpu.h>
#include <asm/arch/hardware.h>
#include <asm/arch/omap.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
#include <asm/io.h>
#include <asm/emif.h>
#include <asm/gpio.h>
#include <i2c.h>
#include <miiphy.h>
#include <cpsw.h>
#include "board.h"

DECLARE_GLOBAL_DATA_PTR;

/* MII mode defines */
#define RMII_RGMII2_MODE_ENABLE	0x49

static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;

#ifdef CONFIG_SPL_BUILD

/* DDR RAM defines */
#define DDR_CLK_MHZ		303 /* DDR_DPLL_MULT value */

#define OSC	(V_OSCK/1000000)
const struct dpll_params dpll_ddr = {
		DDR_CLK_MHZ, OSC-1, 1, -1, -1, -1, -1};

const struct dpll_params *get_dpll_ddr_params(void)
{
	return &dpll_ddr;
}

#ifdef CONFIG_REV1
static const struct ddr_data ddr3_data = {
	.datardsratio0 = MT41J256M8HX15E_RD_DQS,
	.datawdsratio0 = MT41J256M8HX15E_WR_DQS,
	.datafwsratio0 = MT41J256M8HX15E_PHY_FIFO_WE,
	.datawrsratio0 = MT41J256M8HX15E_PHY_WR_DATA,
};

static const struct cmd_control ddr3_cmd_ctrl_data = {
	.cmd0csratio = MT41J256M8HX15E_RATIO,
	.cmd0iclkout = MT41J256M8HX15E_INVERT_CLKOUT,

	.cmd1csratio = MT41J256M8HX15E_RATIO,
	.cmd1iclkout = MT41J256M8HX15E_INVERT_CLKOUT,

	.cmd2csratio = MT41J256M8HX15E_RATIO,
	.cmd2iclkout = MT41J256M8HX15E_INVERT_CLKOUT,
};

static struct emif_regs ddr3_emif_reg_data = {
	.sdram_config = MT41J256M8HX15E_EMIF_SDCFG,
	.ref_ctrl = MT41J256M8HX15E_EMIF_SDREF,
	.sdram_tim1 = MT41J256M8HX15E_EMIF_TIM1,
	.sdram_tim2 = MT41J256M8HX15E_EMIF_TIM2,
	.sdram_tim3 = MT41J256M8HX15E_EMIF_TIM3,
	.zq_config = MT41J256M8HX15E_ZQ_CFG,
	.emif_ddr_phy_ctlr_1 = MT41J256M8HX15E_EMIF_READ_LATENCY |
				PHY_EN_DYN_PWRDN,
};

void sdram_init(void)
{
	config_ddr(DDR_CLK_MHZ, MT41J256M8HX15E_IOCTRL_VALUE, &ddr3_data,
		   &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
}
#else
static const struct ddr_data ddr3_data = {
	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
};

static const struct cmd_control ddr3_cmd_ctrl_data = {
	.cmd0csratio = MT41K256M16HA125E_RATIO,
	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,

	.cmd1csratio = MT41K256M16HA125E_RATIO,
	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,

	.cmd2csratio = MT41K256M16HA125E_RATIO,
	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
};

static struct emif_regs ddr3_emif_reg_data = {
	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
	.zq_config = MT41K256M16HA125E_ZQ_CFG,
	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY |
				PHY_EN_DYN_PWRDN,
};

void sdram_init(void)
{
	config_ddr(DDR_CLK_MHZ, MT41K256M16HA125E_IOCTRL_VALUE, &ddr3_data,
		   &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
}
#endif

void set_uart_mux_conf(void)
{
	enable_uart0_pin_mux();
}

void set_mux_conf_regs(void)
{
	/* Initalize the board header */
	enable_i2c0_pin_mux();
	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);

	enable_board_pin_mux();
}
#endif

/*
 * Basic board specific setup.  Pinmux has been handled already.
 */
int board_init(void)
{
	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);

	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

	return 0;
}

#ifdef CONFIG_DRIVER_TI_CPSW
static void cpsw_control(int enabled)
{
	/* VTP can be added here */

	return;
}

static struct cpsw_slave_data cpsw_slaves[] = {
	{
		.slave_reg_ofs	= 0x208,
		.sliver_reg_ofs	= 0xd80,
		.phy_id		= 0,
		.phy_if		= PHY_INTERFACE_MODE_RGMII,
	},
	{
		.slave_reg_ofs	= 0x308,
		.sliver_reg_ofs	= 0xdc0,
		.phy_id		= 1,
		.phy_if		= PHY_INTERFACE_MODE_RGMII,
	},
};

static struct cpsw_platform_data cpsw_data = {
	.mdio_base		= CPSW_MDIO_BASE,
	.cpsw_base		= CPSW_BASE,
	.mdio_div		= 0xff,
	.channels		= 8,
	.cpdma_reg_ofs		= 0x800,
	.slaves			= 1,
	.slave_data		= cpsw_slaves,
	.ale_reg_ofs		= 0xd00,
	.ale_entries		= 1024,
	.host_port_reg_ofs	= 0x108,
	.hw_stats_reg_ofs	= 0x900,
	.bd_ram_ofs		= 0x2000,
	.mac_control		= (1 << 5),
	.control		= cpsw_control,
	.host_port_num		= 0,
	.version		= CPSW_CTRL_VERSION_2,
};
#endif

#if defined(CONFIG_DRIVER_TI_CPSW) || \
	(defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET))
int board_eth_init(bd_t *bis)
{
	int rv, n = 0;
#ifdef CONFIG_DRIVER_TI_CPSW
	uint8_t mac_addr[6];
	uint32_t mac_hi, mac_lo;

	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
		printf("<ethaddr> not set. Reading from E-fuse\n");
		/* try reading mac address from efuse */
		mac_lo = readl(&cdev->macid0l);
		mac_hi = readl(&cdev->macid0h);
		mac_addr[0] = mac_hi & 0xFF;
		mac_addr[1] = (mac_hi & 0xFF00) >> 8;
		mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
		mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
		mac_addr[4] = mac_lo & 0xFF;
		mac_addr[5] = (mac_lo & 0xFF00) >> 8;

		if (is_valid_ether_addr(mac_addr))
			eth_setenv_enetaddr("ethaddr", mac_addr);
		else
			goto try_usbether;
	}

	writel(RMII_RGMII2_MODE_ENABLE, &cdev->miisel);

	rv = cpsw_register(&cpsw_data);
	if (rv < 0)
		printf("Error %d registering CPSW switch\n", rv);
	else
		n += rv;
try_usbether:
#endif

#if defined(CONFIG_USB_ETHER) && !defined(CONFIG_SPL_BUILD)
	rv = usb_eth_initialize(bis);
	if (rv < 0)
		printf("Error %d registering USB_ETHER\n", rv);
	else
		n += rv;
#endif
	return n;
}
#endif