upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/drivers/serial/vct.c

125 lines
3.4 KiB

/*
* (C) Copyright 2008 Stefan Roese <sr@denx.de>, DENX Software Engineering
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <config.h>
#include <common.h>
#include <asm/io.h>
#ifdef CONFIG_VCT_PLATINUMAVC
#define UART_1_BASE 0xBDC30000
#else
#define UART_1_BASE 0xBF89C000
#endif
#define UART_RBR_OFF 0x00 /* receiver buffer reg */
#define UART_THR_OFF 0x00 /* transmit holding reg */
#define UART_DLL_OFF 0x00 /* divisor latch low reg */
#define UART_IER_OFF 0x04 /* interrupt enable reg */
#define UART_DLH_OFF 0x04 /* receiver buffer reg */
#define UART_FCR_OFF 0x08 /* fifo control register */
#define UART_LCR_OFF 0x0c /* line control register */
#define UART_MCR_OFF 0x10 /* modem control register */
#define UART_LSR_OFF 0x14 /* line status register */
#define UART_MSR_OFF 0x18 /* modem status register */
#define UART_SCR_OFF 0x1c /* scratch pad register */
#define UART_RCV_DATA_RDY 0x01 /* Data Received */
#define UART_XMT_HOLD_EMPTY 0x20
#define UART_TRANSMIT_EMPTY 0x40
/* 7 bit on line control reg. enalbing rw to dll and dlh */
#define UART_LCR_DLAB 0x0080
#define UART___9600_BDR 0x84
#define UART__19200_BDR 0x42
#define UART_115200_BDR 0x08
#define UART_DIS_ALL_INTER 0x00 /* disable all interrupts */
#define UART_5DATA_BITS 0x0000 /* 5 [bits] 1.5 bits 2 */
#define UART_6DATA_BITS 0x0001 /* 6 [bits] 1 bits 2 */
#define UART_7DATA_BITS 0x0002 /* 7 [bits] 1 bits 2 */
#define UART_8DATA_BITS 0x0003 /* 8 [bits] 1 bits 2 */
static void vct_uart_set_baud_rate(u32 address, u32 dh, u32 dl)
{
u32 val = __raw_readl(UART_1_BASE + UART_LCR_OFF);
/* set 7 bit on 1 */
val |= UART_LCR_DLAB;
__raw_writel(val, UART_1_BASE + UART_LCR_OFF);
__raw_writel(dl, UART_1_BASE + UART_DLL_OFF);
__raw_writel(dh, UART_1_BASE + UART_DLH_OFF);
/* set 7 bit on 0 */
val &= ~UART_LCR_DLAB;
__raw_writel(val, UART_1_BASE + UART_LCR_OFF);
return;
}
int serial_init(void)
{
__raw_writel(UART_DIS_ALL_INTER, UART_1_BASE + UART_IER_OFF);
vct_uart_set_baud_rate(UART_1_BASE, 0, UART_115200_BDR);
__raw_writel(UART_8DATA_BITS, UART_1_BASE + UART_LCR_OFF);
return 0;
}
void serial_setbrg(void)
{
/*
* Baudrate change not supported currently, fixed to 115200 baud
*/
}
void serial_putc(const char c)
{
if (c == '\n')
serial_putc('\r');
while (!(UART_XMT_HOLD_EMPTY & __raw_readl(UART_1_BASE + UART_LSR_OFF)))
;
__raw_writel(c, UART_1_BASE + UART_THR_OFF);
}
void serial_puts(const char *s)
{
while (*s)
serial_putc(*s++);
}
int serial_getc(void)
{
while (!(UART_RCV_DATA_RDY & __raw_readl(UART_1_BASE + UART_LSR_OFF)))
;
return __raw_readl(UART_1_BASE + UART_RBR_OFF) & 0xff;
}
int serial_tstc(void)
{
if (!(UART_RCV_DATA_RDY & __raw_readl(UART_1_BASE + UART_LSR_OFF)))
return 0;
return 1;
}