upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
194 lines
6.7 KiB
194 lines
6.7 KiB
/*
|
|
* (C) Copyright 2000-2004
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_405GP 1 /* This is a PPC405GP CPU */
|
|
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
|
|
#define CONFIG_EXBITGEN 1 /* on a Exbit Generic board */
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
|
|
|
|
#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
|
|
|
|
/* I2C configuration */
|
|
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
|
|
#define CONFIG_SYS_I2C_SPEED 40000 /* I2C speed */
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */
|
|
|
|
/* environment is in EEPROM */
|
|
#define CONFIG_ENV_IS_IN_EEPROM 1
|
|
#undef CONFIG_ENV_IS_IN_FLASH
|
|
#undef CONFIG_ENV_IS_IN_NVRAM
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_EEPROM
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x56 /* 1010110 */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit internal addressing */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 1 /* ... and 1 bit in I2C address */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* 4 bytes per page */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* write takes up to 40 msec */
|
|
#define CONFIG_ENV_OFFSET 4 /* Offset of Environment Sector */
|
|
#define CONFIG_ENV_SIZE 350 /* that is 350 bytes only! */
|
|
#endif
|
|
|
|
#define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */
|
|
/* Explanation:
|
|
autbooting is altogether disabled and cannot be
|
|
enabled if CONFIG_BOOTDELAY is negative.
|
|
If you want shorter bootdelay, then
|
|
- "setenv bootdelay <delay>" to the proper value
|
|
*/
|
|
|
|
#define CONFIG_BOOTCOMMAND "bootm 20400000 20800000"
|
|
|
|
#define CONFIG_BOOTARGS "root=/dev/ram " \
|
|
"ramdisk_size=32768 " \
|
|
"console=ttyS0,115200 " \
|
|
"ram=128M debug"
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_PHY_ADDR 0 /* PHY address */
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_PPC4xx_EMAC
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
/* UART configuration */
|
|
#define CONFIG_SYS_BASE_BAUD 691200
|
|
|
|
/* Default baud rate */
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
/* The following table includes the supported baudrates */
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
|
|
57600, 115200, 230400, 460800, 921600 }
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
|
|
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCI stuff
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#undef CONFIG_PCI /* no pci support */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* External peripheral base address
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#undef CONFIG_IDE_PCMCIA /* no pcmcia interface required */
|
|
#undef CONFIG_IDE_LED /* no led for ide supported */
|
|
#undef CONFIG_IDE_RESET /* no reset for ide supported */
|
|
|
|
#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000
|
|
#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000
|
|
#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH0_BASE 0xFFF80000
|
|
#define CONFIG_SYS_FLASH0_SIZE 0x00080000
|
|
#define CONFIG_SYS_FLASH1_BASE 0x20000000
|
|
#define CONFIG_SYS_FLASH1_SIZE 0x02000000
|
|
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
|
|
#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
|
|
|
|
#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH0_BASE
|
|
#define CONFIG_SYS_RAMSTART
|
|
#endif
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 5 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_FLASH
|
|
#define CONFIG_ENV_OFFSET 0x00060000 /* Offset of Environment Sector */
|
|
#define CONFIG_ENV_SIZE 0x00010000 /* Total Size of Environment Sector */
|
|
#define CONFIG_ENV_SECT_SIZE 0x00010000 /* see README - env sector total size */
|
|
#endif
|
|
|
|
/* On Chip Memory location/size */
|
|
#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
|
|
#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
|
|
|
|
/* Global info and initial stack */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
|
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
|
|
#endif
|
|
#endif /* __CONFIG_H */
|
|
|