upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
767 lines
24 KiB
767 lines
24 KiB
/*
|
|
* (C) Copyright 2002
|
|
* Frank Panno <fpanno@delphintech.com>, Delphin Technology AG
|
|
*
|
|
* This file is based on similar values for other boards found in other
|
|
* U-Boot config files, and some that I found in the EP8260 manual.
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*
|
|
* "EP8260 H, V.1.1"
|
|
* - 64M 60x Bus SDRAM
|
|
* - 32M Local Bus SDRAM
|
|
* - 16M Flash (4 x AM29DL323DB90WDI)
|
|
* - 128k NVRAM with RTC
|
|
*
|
|
* "EP8260 H2, V.1.3" (CONFIG_SYS_EP8260_H2)
|
|
* - 300MHz/133MHz/66MHz
|
|
* - 64M 60x Bus SDRAM
|
|
* - 32M Local Bus SDRAM
|
|
* - 32M Flash
|
|
* - 128k NVRAM with RTC
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/* Define this to enable support the EP8260 H2 version */
|
|
#define CONFIG_SYS_EP8260_H2 1
|
|
/* #undef CONFIG_SYS_EP8260_H2 */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xFFF00000
|
|
|
|
#define CONFIG_CPM2 1 /* Has a CPM2 */
|
|
|
|
/* What is the oscillator's (UX2) frequency in Hz? */
|
|
#define CONFIG_8260_CLKIN (66 * 1000 * 1000)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual
|
|
*-----------------------------------------------------------------------
|
|
* What should MODCK_H be? It is dependent on the oscillator
|
|
* frequency, MODCK[1-3], and desired CPM and core frequencies.
|
|
* Here are some example values (all frequencies are in MHz):
|
|
*
|
|
* MODCK_H MODCK[1-3] Osc CPM Core
|
|
* ------- ---------- --- --- ----
|
|
* 0x2 0x2 33 133 133
|
|
* 0x2 0x3 33 133 166
|
|
* 0x2 0x4 33 133 200
|
|
* 0x2 0x5 33 133 233
|
|
* 0x2 0x6 33 133 266
|
|
*
|
|
* 0x5 0x5 66 133 133
|
|
* 0x5 0x6 66 133 166
|
|
* 0x5 0x7 66 133 200 *
|
|
* 0x6 0x0 66 133 233
|
|
* 0x6 0x1 66 133 266
|
|
* 0x6 0x2 66 133 300
|
|
*/
|
|
#ifdef CONFIG_SYS_EP8260_H2
|
|
#define CONFIG_SYS_SBC_MODCK_H (HRCW_MODCK_H0110)
|
|
#else
|
|
#define CONFIG_SYS_SBC_MODCK_H (HRCW_MODCK_H0110)
|
|
#endif
|
|
|
|
/* Define this if you want to boot from 0x00000100. If you don't define
|
|
* this, you will need to program the bootloader to 0xfff00000, and
|
|
* get the hardware reset config words at 0xfe000000. The simplest
|
|
* way to do that is to program the bootloader at both addresses.
|
|
* It is suggested that you just let U-Boot live at 0x00000000.
|
|
*/
|
|
/* #define CONFIG_SYS_SBC_BOOT_LOW 1 */ /* only for HRCW */
|
|
/* #undef CONFIG_SYS_SBC_BOOT_LOW */
|
|
|
|
/* The reset command will not work as expected if the reset address does
|
|
* not point to the correct address.
|
|
*/
|
|
|
|
#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
|
|
|
|
/* What should the base address of the main FLASH be and how big is
|
|
* it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/ep8260/config.mk
|
|
* The main FLASH is whichever is connected to *CS0. U-Boot expects
|
|
* this to be the SIMM.
|
|
*/
|
|
#ifdef CONFIG_SYS_EP8260_H2
|
|
#define CONFIG_SYS_FLASH0_BASE 0xFE000000
|
|
#define CONFIG_SYS_FLASH0_SIZE 32
|
|
#else
|
|
#define CONFIG_SYS_FLASH0_BASE 0xFF000000
|
|
#define CONFIG_SYS_FLASH0_SIZE 16
|
|
#endif
|
|
|
|
/* What should the base address of the secondary FLASH be and how big
|
|
* is it (in Mbytes)? The secondary FLASH is whichever is connected
|
|
* to *CS6. U-Boot expects this to be the on board FLASH. If you don't
|
|
* want it enabled, don't define these constants.
|
|
*/
|
|
#define CONFIG_SYS_FLASH1_BASE 0
|
|
#define CONFIG_SYS_FLASH1_SIZE 0
|
|
#undef CONFIG_SYS_FLASH1_BASE
|
|
#undef CONFIG_SYS_FLASH1_SIZE
|
|
|
|
/* What should be the base address of SDRAM DIMM (60x bus) and how big is
|
|
* it (in Mbytes)?
|
|
*/
|
|
#define CONFIG_SYS_SDRAM0_BASE 0x00000000
|
|
#define CONFIG_SYS_SDRAM0_SIZE 64
|
|
|
|
/* define CONFIG_SYS_LSDRAM if you want to enable the 32M SDRAM on the
|
|
* local bus (8260 local bus is NOT cacheable!)
|
|
*/
|
|
/* #define CONFIG_SYS_LSDRAM */
|
|
#undef CONFIG_SYS_LSDRAM
|
|
|
|
#ifdef CONFIG_SYS_LSDRAM
|
|
/* What should be the base address of SDRAM DIMM (local bus) and how big is
|
|
* it (in Mbytes)?
|
|
*/
|
|
#define CONFIG_SYS_SDRAM1_BASE 0x04000000
|
|
#define CONFIG_SYS_SDRAM1_SIZE 32
|
|
#else
|
|
#define CONFIG_SYS_SDRAM1_BASE 0
|
|
#define CONFIG_SYS_SDRAM1_SIZE 0
|
|
#undef CONFIG_SYS_SDRAM1_BASE
|
|
#undef CONFIG_SYS_SDRAM1_SIZE
|
|
#endif /* CONFIG_SYS_LSDRAM */
|
|
|
|
/* What should be the base address of NVRAM and how big is
|
|
* it (in Bytes)
|
|
*/
|
|
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xFA080000
|
|
#define CONFIG_SYS_NVRAM_SIZE (128*1024)-16
|
|
|
|
/* The RTC is a Dallas DS1556
|
|
*/
|
|
#define CONFIG_RTC_DS1556
|
|
|
|
/* What should be the base address of the LEDs and switch S0?
|
|
* If you don't want them enabled, don't define this.
|
|
*/
|
|
#define CONFIG_SYS_LED_BASE 0x00000000
|
|
#undef CONFIG_SYS_LED_BASE
|
|
|
|
/*
|
|
* select serial console configuration
|
|
*
|
|
* if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
|
|
* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
|
|
* for SCC).
|
|
*
|
|
* if CONFIG_CONS_NONE is defined, then the serial console routines must
|
|
* defined elsewhere.
|
|
*/
|
|
#define CONFIG_CONS_ON_SMC /* define if console on SMC */
|
|
#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
|
|
#undef CONFIG_CONS_NONE /* define if console on neither */
|
|
#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */
|
|
|
|
/*
|
|
* select ethernet configuration
|
|
*
|
|
* if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
|
|
* CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
|
|
* for FCC)
|
|
*
|
|
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
|
|
* defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
|
|
*/
|
|
#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */
|
|
#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */
|
|
#undef CONFIG_ETHER_NONE /* define if ethernet on neither */
|
|
#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */
|
|
|
|
#if ( CONFIG_ETHER_INDEX == 3 )
|
|
|
|
/*
|
|
* - Rx-CLK is CLK15
|
|
* - Tx-CLK is CLK16
|
|
* - RAM for BD/Buffers is on the local Bus (see 28-13)
|
|
* - Enable Half Duplex in FSMR
|
|
*/
|
|
# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
|
|
# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
|
|
|
|
/*
|
|
* - RAM for BD/Buffers is on the local Bus (see 28-13)
|
|
*/
|
|
#ifdef CONFIG_SYS_LSDRAM
|
|
#define CONFIG_SYS_CPMFCR_RAMTYPE 3
|
|
#else /* CONFIG_SYS_LSDRAM */
|
|
#define CONFIG_SYS_CPMFCR_RAMTYPE 0
|
|
#endif /* CONFIG_SYS_LSDRAM */
|
|
|
|
/* - Enable Half Duplex in FSMR */
|
|
/* # define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */
|
|
# define CONFIG_SYS_FCC_PSMR 0
|
|
|
|
#else /* CONFIG_ETHER_INDEX */
|
|
# error "on EP8260 ethernet must be FCC3"
|
|
#endif /* CONFIG_ETHER_INDEX */
|
|
|
|
/*
|
|
* select i2c support configuration
|
|
*
|
|
* Supported configurations are {none, software, hardware} drivers.
|
|
* If the software driver is chosen, there are some additional
|
|
* configuration items that the driver uses to drive the port pins.
|
|
*/
|
|
#undef CONFIG_HARD_I2C /* I2C with hardware support */
|
|
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
|
|
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F
|
|
|
|
/*
|
|
* Software (bit-bang) I2C driver configuration
|
|
*/
|
|
#ifdef CONFIG_SOFT_I2C
|
|
#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
|
|
#define I2C_ACTIVE (iop->pdir |= 0x00010000)
|
|
#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
|
|
#define I2C_READ ((iop->pdat & 0x00010000) != 0)
|
|
#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
|
|
else iop->pdat &= ~0x00010000
|
|
#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
|
|
else iop->pdat &= ~0x00020000
|
|
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
|
#endif /* CONFIG_SOFT_I2C */
|
|
|
|
/* #define CONFIG_RTC_DS174x */
|
|
|
|
/* Define this to reserve an entire FLASH sector (256 KB) for
|
|
* environment variables. Otherwise, the environment will be
|
|
* put in the same sector as U-Boot, and changing variables
|
|
* will erase U-Boot temporarily
|
|
*/
|
|
#define CONFIG_ENV_IN_OWN_SECT
|
|
|
|
/* Define to allow the user to overwrite serial and ethaddr */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
/* What should the console's baud rate be? */
|
|
#ifdef CONFIG_SYS_EP8260_H2
|
|
#define CONFIG_BAUDRATE 9600
|
|
#else
|
|
#define CONFIG_BAUDRATE 115200
|
|
#endif
|
|
|
|
/* Ethernet MAC address */
|
|
#define CONFIG_ETHADDR 00:10:EC:00:30:8C
|
|
|
|
#define CONFIG_IPADDR 192.168.254.130
|
|
#define CONFIG_SERVERIP 192.168.254.49
|
|
|
|
/* Set to a positive value to delay for running BOOTCOMMAND */
|
|
#define CONFIG_BOOTDELAY -1
|
|
|
|
/* undef this to save memory */
|
|
#define CONFIG_SYS_LONGHELP
|
|
|
|
/* Monitor Command Prompt */
|
|
#define CONFIG_SYS_PROMPT "=> "
|
|
|
|
/* Define this variable to enable the "hush" shell (from
|
|
Busybox) as command line interpreter, thus enabling
|
|
powerful command line syntax like
|
|
if...then...else...fi conditionals or `&&' and '||'
|
|
constructs ("shell scripts").
|
|
If undefined, you get the old, much simpler behaviour
|
|
with a somewhat smapper memory footprint.
|
|
*/
|
|
#define CONFIG_SYS_HUSH_PARSER
|
|
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_ASKENV
|
|
#define CONFIG_CMD_BEDBUG
|
|
#define CONFIG_CMD_CACHE
|
|
#define CONFIG_CMD_CDP
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_DIAG
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_FAT
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_IMMAP
|
|
#define CONFIG_CMD_IRQ
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_PORTIO
|
|
#define CONFIG_CMD_REGINFO
|
|
#define CONFIG_CMD_SAVES
|
|
#define CONFIG_CMD_SDRAM
|
|
#define CONFIG_CMD_SNTP
|
|
|
|
#undef CONFIG_CMD_DCR
|
|
#undef CONFIG_CMD_XIMG
|
|
|
|
/* Where do the internal registers live? */
|
|
#define CONFIG_SYS_IMMR 0xF0000000
|
|
#define CONFIG_SYS_DEFAULT_IMMR 0x00010000
|
|
|
|
/* Where do the on board registers (CS4) live? */
|
|
#define CONFIG_SYS_REGS_BASE 0xFA000000
|
|
|
|
/*****************************************************************************
|
|
*
|
|
* You should not have to modify any of the following settings
|
|
*
|
|
*****************************************************************************/
|
|
|
|
#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
|
|
#define CONFIG_EP8260 11 /* on an Embedded Planet EP8260 Board, Rev. 11 */
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
|
|
/* Print Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
|
|
|
|
#define CONFIG_SYS_MAXARGS 8 /* max number of command args */
|
|
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#ifdef CONFIG_SYS_LSDRAM
|
|
#define CONFIG_SYS_MEMTEST_START 0x04000000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */
|
|
#else
|
|
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0-32 MB in SDRAM */
|
|
#endif /* CONFIG_SYS_LSDRAM */
|
|
|
|
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
|
|
#define CONFIG_SYS_TFTP_LOADADDR 0x00100000 /* default load address for network file downloads */
|
|
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
/* valid baudrates */
|
|
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
|
|
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Hard Reset Configuration Words
|
|
*/
|
|
|
|
#if defined(CONFIG_SYS_SBC_BOOT_LOW)
|
|
# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
|
|
#else
|
|
# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0x00000000)
|
|
#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
|
|
|
|
#ifdef CONFIG_SYS_EP8260_H2
|
|
/* get the HRCW ISB field from CONFIG_SYS_DEFAULT_IMMR */
|
|
#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_DEFAULT_IMMR & 0x10000000) >> 10) |\
|
|
((CONFIG_SYS_DEFAULT_IMMR & 0x01000000) >> 7) |\
|
|
((CONFIG_SYS_DEFAULT_IMMR & 0x00100000) >> 4) )
|
|
|
|
#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM |\
|
|
HRCW_L2CPC01 |\
|
|
CONFIG_SYS_SBC_HRCW_IMMR |\
|
|
HRCW_APPC10 |\
|
|
HRCW_CS10PC01 |\
|
|
CONFIG_SYS_SBC_MODCK_H |\
|
|
CONFIG_SYS_SBC_HRCW_BOOT_FLAGS)
|
|
#else
|
|
#define CONFIG_SYS_HRCW_MASTER 0x10400245
|
|
#endif
|
|
|
|
/* no slaves */
|
|
#define CONFIG_SYS_HRCW_SLAVE1 0
|
|
#define CONFIG_SYS_HRCW_SLAVE2 0
|
|
#define CONFIG_SYS_HRCW_SLAVE3 0
|
|
#define CONFIG_SYS_HRCW_SLAVE4 0
|
|
#define CONFIG_SYS_HRCW_SLAVE5 0
|
|
#define CONFIG_SYS_HRCW_SLAVE6 0
|
|
#define CONFIG_SYS_HRCW_SLAVE7 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
* Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
|
|
*/
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
|
|
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
|
# define CONFIG_SYS_RAMBOOT
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH and environment organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#ifdef CONFIG_SYS_EP8260_H2
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
|
|
#else
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
|
|
#endif
|
|
|
|
#ifdef CONFIG_SYS_EP8260_H2
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
#else
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
|
|
#endif
|
|
|
|
#ifndef CONFIG_SYS_RAMBOOT
|
|
# define CONFIG_ENV_IS_IN_FLASH 1
|
|
|
|
# ifdef CONFIG_ENV_IN_OWN_SECT
|
|
# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
|
|
# define CONFIG_ENV_SECT_SIZE 0x40000
|
|
# else
|
|
# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
|
|
# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
|
|
# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */
|
|
# endif /* CONFIG_ENV_IN_OWN_SECT */
|
|
#else
|
|
# define CONFIG_ENV_IS_IN_NVRAM 1
|
|
# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
|
|
# define CONFIG_ENV_SIZE 0x200
|
|
#endif /* CONFIG_SYS_RAMBOOT */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* HIDx - Hardware Implementation-dependent Registers 2-11
|
|
*-----------------------------------------------------------------------
|
|
* HID0 also contains cache control - initially enable both caches and
|
|
* invalidate contents, then the final state leaves only the instruction
|
|
* cache enabled. Note that Power-On and Hard reset invalidate the caches,
|
|
* but Soft reset does not.
|
|
*
|
|
* HID1 has only read-only information - nothing to set.
|
|
*/
|
|
#define CONFIG_SYS_HID0_INIT (HID0_ICE |\
|
|
HID0_DCE |\
|
|
HID0_ICFI |\
|
|
HID0_DCI |\
|
|
HID0_IFEM |\
|
|
HID0_ABE)
|
|
#ifdef CONFIG_SYS_LSDRAM
|
|
/* 8260 local bus is NOT cacheable */
|
|
#define CONFIG_SYS_HID0_FINAL (/*HID0_ICE |*/\
|
|
HID0_IFEM |\
|
|
HID0_ABE |\
|
|
HID0_EMCP)
|
|
#else /* !CONFIG_SYS_LSDRAM */
|
|
#define CONFIG_SYS_HID0_FINAL (HID0_ICE |\
|
|
HID0_IFEM |\
|
|
HID0_ABE |\
|
|
HID0_EMCP)
|
|
#endif /* CONFIG_SYS_LSDRAM */
|
|
|
|
#define CONFIG_SYS_HID2 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RMR - Reset Mode Register
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_RMR 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* BCR - Bus Configuration 4-25
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_BCR (BCR_EBM |\
|
|
BCR_PLDP |\
|
|
BCR_EAV |\
|
|
BCR_NPQM0)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 4-31
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_L2CPC01 |\
|
|
SIUMCR_APPC10 |\
|
|
SIUMCR_CS10PC01)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 11-9
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
|
|
*/
|
|
#ifdef CONFIG_SYS_EP8260_H2
|
|
/* TBD: Find out why setting the BMT to 0xff causes the FCC to
|
|
* generate TX buffer underrun errors for large packets under
|
|
* Linux
|
|
*/
|
|
#define CONFIG_SYS_SYPCR_BMT 0x00000600
|
|
#else
|
|
#define CONFIG_SYS_SYPCR_BMT SYPCR_BMT
|
|
#endif
|
|
|
|
#ifdef CONFIG_SYS_LSDRAM
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
|
|
CONFIG_SYS_SYPCR_BMT |\
|
|
SYPCR_PBME |\
|
|
SYPCR_LBME |\
|
|
SYPCR_SWP)
|
|
#else
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
|
|
CONFIG_SYS_SYPCR_BMT |\
|
|
SYPCR_PBME |\
|
|
SYPCR_SWP)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TMCNTSC - Time Counter Status and Control 4-40
|
|
*-----------------------------------------------------------------------
|
|
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
|
|
* and enable Time Counter
|
|
*/
|
|
#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\
|
|
TMCNTSC_ALR |\
|
|
TMCNTSC_TCF |\
|
|
TMCNTSC_TCE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 4-42
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
|
|
* Periodic timer
|
|
*/
|
|
#ifdef CONFIG_SYS_EP8260_H2
|
|
#define CONFIG_SYS_PISCR (PISCR_PS |\
|
|
PISCR_PTF |\
|
|
PISCR_PTE)
|
|
#else
|
|
#define CONFIG_SYS_PISCR 0
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SCCR - System Clock Control 9-8
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#ifdef CONFIG_SYS_EP8260_H2
|
|
#define CONFIG_SYS_SCCR (SCCR_DFBRG00)
|
|
#else
|
|
#define CONFIG_SYS_SCCR (SCCR_DFBRG01)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RCCR - RISC Controller Configuration 13-7
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_RCCR 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* MPTPR - Memory Refresh Timer Prescale Register 10-32
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_MPTPR (0x0A00 & MPTPR_PTP_MSK)
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* Bank Bus Machine PortSz Device
|
|
* ---- --- ------- ------ ------
|
|
* 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90WDI)
|
|
* 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Micron 48LC8M16A2TG)
|
|
* 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Micron 48LC8M16A2TG)
|
|
* 3 unused
|
|
* 4 60x GPCM 8 bit Board Regs, NVRTC
|
|
* 5 unused
|
|
* 6 unused
|
|
* 7 unused
|
|
* 8 PCMCIA
|
|
* 9 unused
|
|
* 10 unused
|
|
* 11 unused
|
|
*/
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* BRx - Base Register
|
|
* Ref: Section 10.3.1 on page 10-14
|
|
* ORx - Option Register
|
|
* Ref: Section 10.3.2 on page 10-18
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
/* Bank 0 - FLASH
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_64 |\
|
|
BRx_DECC_NONE |\
|
|
BRx_MS_GPCM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\
|
|
ORxG_CSNT |\
|
|
ORxG_ACS_DIV1 |\
|
|
ORxG_SCY_8_CLK |\
|
|
ORxG_EHTR)
|
|
|
|
/* Bank 1 - SDRAM
|
|
* PSDRAM
|
|
*/
|
|
#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_64 |\
|
|
BRx_MS_SDRAM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\
|
|
ORxS_BPD_4 |\
|
|
ORxS_ROWST_PBI1_A6 |\
|
|
ORxS_NUMR_12)
|
|
|
|
#ifdef CONFIG_SYS_EP8260_H2
|
|
#define CONFIG_SYS_PSDMR 0xC34E246E
|
|
#else
|
|
#define CONFIG_SYS_PSDMR 0xC34E2462
|
|
#endif
|
|
|
|
#define CONFIG_SYS_PSRT 0x64
|
|
|
|
#ifdef CONFIG_SYS_LSDRAM
|
|
/* Bank 2 - SDRAM
|
|
* LSDRAM
|
|
*/
|
|
|
|
#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_32 |\
|
|
BRx_MS_SDRAM_L |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) |\
|
|
ORxS_BPD_4 |\
|
|
ORxS_ROWST_PBI0_A9 |\
|
|
ORxS_NUMR_12)
|
|
|
|
#define CONFIG_SYS_LSDMR 0x416A2562
|
|
#define CONFIG_SYS_LSRT 0x64
|
|
#else
|
|
#define CONFIG_SYS_LSRT 0x0
|
|
#endif /* CONFIG_SYS_LSDRAM */
|
|
|
|
/* Bank 4 - On board registers
|
|
* NVRTC and BCSR
|
|
*/
|
|
#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_8 |\
|
|
BRx_MS_GPCM_P |\
|
|
BRx_V)
|
|
/*
|
|
#define CONFIG_SYS_OR4_PRELIM (ORxG_AM_MSK |\
|
|
ORxG_CSNT |\
|
|
ORxG_ACS_DIV1 |\
|
|
ORxG_SCY_10_CLK |\
|
|
ORxG_TRLX)
|
|
*/
|
|
#define CONFIG_SYS_OR4_PRELIM 0xfff00854
|
|
|
|
#ifdef _NOT_USED_SINCE_NOT_WORKING_
|
|
/* Bank 8 - On board registers
|
|
* PCMCIA (currently not working!)
|
|
*/
|
|
#define CONFIG_SYS_BR8_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_16 |\
|
|
BRx_MS_GPCM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR8_PRELIM (ORxG_AM_MSK |\
|
|
ORxG_CSNT |\
|
|
ORxG_ACS_DIV1 |\
|
|
ORxG_SETA |\
|
|
ORxG_SCY_10_CLK)
|
|
#endif
|
|
|
|
/*
|
|
* JFFS2 partitions
|
|
*
|
|
*/
|
|
/* No command line, one static partition, whole device */
|
|
#undef CONFIG_CMD_MTDPARTS
|
|
#define CONFIG_JFFS2_DEV "nor0"
|
|
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
|
|
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
|
|
|
|
/* mtdparts command line support */
|
|
/* Note: fake mtd_id used, no linux mtd map file */
|
|
/*
|
|
#define CONFIG_CMD_MTDPARTS
|
|
#define MTDIDS_DEFAULT ""
|
|
#define MTDPARTS_DEFAULT ""
|
|
*/
|
|
|
|
#endif /* __CONFIG_H */
|
|
|