upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
435 lines
9.2 KiB
435 lines
9.2 KiB
/*
|
|
* Copyright 2017 NXP
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <malloc.h>
|
|
#include <errno.h>
|
|
#include <netdev.h>
|
|
#include <fsl_ifc.h>
|
|
#include <fsl_ddr.h>
|
|
#include <fsl_sec.h>
|
|
#include <asm/io.h>
|
|
#include <fdt_support.h>
|
|
#include <libfdt.h>
|
|
#include <fsl-mc/fsl_mc.h>
|
|
#include <environment.h>
|
|
#include <asm/arch-fsl-layerscape/soc.h>
|
|
#include <asm/arch/ppa.h>
|
|
|
|
#include "../common/qixis.h"
|
|
#include "ls1088a_qixis.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
unsigned long long get_qixis_addr(void)
|
|
{
|
|
unsigned long long addr;
|
|
|
|
if (gd->flags & GD_FLG_RELOC)
|
|
addr = QIXIS_BASE_PHYS;
|
|
else
|
|
addr = QIXIS_BASE_PHYS_EARLY;
|
|
|
|
/*
|
|
* IFC address under 256MB is mapped to 0x30000000, any address above
|
|
* is mapped to 0x5_10000000 up to 4GB.
|
|
*/
|
|
addr = addr > 0x10000000 ? addr + 0x500000000ULL : addr + 0x30000000;
|
|
|
|
return addr;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
char buf[64];
|
|
u8 sw;
|
|
static const char *const freq[] = {"100", "125", "156.25",
|
|
"100 separate SSCG"};
|
|
int clock;
|
|
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
printf("Board: LS1088A-QDS, ");
|
|
#else
|
|
printf("Board: LS1088A-RDB, ");
|
|
#endif
|
|
|
|
sw = QIXIS_READ(arch);
|
|
printf("Board Arch: V%d, ", sw >> 4);
|
|
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
printf("Board version: %c, boot from ", (sw & 0xf) + 'A' - 1);
|
|
#else
|
|
printf("Board version: %c, boot from ", (sw & 0xf) + 'A');
|
|
#endif
|
|
|
|
memset((u8 *)buf, 0x00, ARRAY_SIZE(buf));
|
|
|
|
sw = QIXIS_READ(brdcfg[0]);
|
|
sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
|
|
|
|
#ifdef CONFIG_SD_BOOT
|
|
puts("SD card\n");
|
|
#endif
|
|
switch (sw) {
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
case 0:
|
|
case 1:
|
|
case 2:
|
|
case 3:
|
|
case 4:
|
|
case 5:
|
|
case 6:
|
|
case 7:
|
|
printf("vBank: %d\n", sw);
|
|
break;
|
|
case 8:
|
|
puts("PromJet\n");
|
|
break;
|
|
case 15:
|
|
puts("IFCCard\n");
|
|
break;
|
|
case 14:
|
|
#else
|
|
case 0:
|
|
#endif
|
|
puts("QSPI:");
|
|
sw = QIXIS_READ(brdcfg[0]);
|
|
sw = (sw & QIXIS_QMAP_MASK) >> QIXIS_QMAP_SHIFT;
|
|
if (sw == 0 || sw == 4)
|
|
puts("0\n");
|
|
else if (sw == 1)
|
|
puts("1\n");
|
|
else
|
|
puts("EMU\n");
|
|
break;
|
|
|
|
default:
|
|
printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
|
|
break;
|
|
}
|
|
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
printf("FPGA: v%d (%s), build %d",
|
|
(int)QIXIS_READ(scver), qixis_read_tag(buf),
|
|
(int)qixis_read_minor());
|
|
/* the timestamp string contains "\n" at the end */
|
|
printf(" on %s", qixis_read_time(buf));
|
|
#else
|
|
printf("CPLD: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata));
|
|
#endif
|
|
|
|
/*
|
|
* Display the actual SERDES reference clocks as configured by the
|
|
* dip switches on the board. Note that the SWx registers could
|
|
* technically be set to force the reference clocks to match the
|
|
* values that the SERDES expects (or vice versa). For now, however,
|
|
* we just display both values and hope the user notices when they
|
|
* don't match.
|
|
*/
|
|
puts("SERDES1 Reference : ");
|
|
sw = QIXIS_READ(brdcfg[2]);
|
|
clock = (sw >> 6) & 3;
|
|
printf("Clock1 = %sMHz ", freq[clock]);
|
|
clock = (sw >> 4) & 3;
|
|
printf("Clock2 = %sMHz", freq[clock]);
|
|
|
|
puts("\nSERDES2 Reference : ");
|
|
clock = (sw >> 2) & 3;
|
|
printf("Clock1 = %sMHz ", freq[clock]);
|
|
clock = (sw >> 0) & 3;
|
|
printf("Clock2 = %sMHz\n", freq[clock]);
|
|
|
|
return 0;
|
|
}
|
|
|
|
bool if_board_diff_clk(void)
|
|
{
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
u8 diff_conf = QIXIS_READ(brdcfg[11]);
|
|
return diff_conf & 0x40;
|
|
#else
|
|
u8 diff_conf = QIXIS_READ(dutcfg[11]);
|
|
return diff_conf & 0x80;
|
|
#endif
|
|
}
|
|
|
|
unsigned long get_board_sys_clk(void)
|
|
{
|
|
u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
|
|
|
|
switch (sysclk_conf & 0x0f) {
|
|
case QIXIS_SYSCLK_83:
|
|
return 83333333;
|
|
case QIXIS_SYSCLK_100:
|
|
return 100000000;
|
|
case QIXIS_SYSCLK_125:
|
|
return 125000000;
|
|
case QIXIS_SYSCLK_133:
|
|
return 133333333;
|
|
case QIXIS_SYSCLK_150:
|
|
return 150000000;
|
|
case QIXIS_SYSCLK_160:
|
|
return 160000000;
|
|
case QIXIS_SYSCLK_166:
|
|
return 166666666;
|
|
}
|
|
|
|
return 66666666;
|
|
}
|
|
|
|
unsigned long get_board_ddr_clk(void)
|
|
{
|
|
u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
|
|
|
|
if (if_board_diff_clk())
|
|
return get_board_sys_clk();
|
|
switch ((ddrclk_conf & 0x30) >> 4) {
|
|
case QIXIS_DDRCLK_100:
|
|
return 100000000;
|
|
case QIXIS_DDRCLK_125:
|
|
return 125000000;
|
|
case QIXIS_DDRCLK_133:
|
|
return 133333333;
|
|
}
|
|
|
|
return 66666666;
|
|
}
|
|
|
|
int select_i2c_ch_pca9547(u8 ch)
|
|
{
|
|
int ret;
|
|
|
|
ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
|
|
if (ret) {
|
|
puts("PCA: failed to select proper channel\n");
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
void board_retimer_init(void)
|
|
{
|
|
u8 reg;
|
|
|
|
/* Retimer is connected to I2C1_CH5 */
|
|
select_i2c_ch_pca9547(I2C_MUX_CH5);
|
|
|
|
/* Access to Control/Shared register */
|
|
reg = 0x0;
|
|
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
|
|
|
|
/* Read device revision and ID */
|
|
i2c_read(I2C_RETIMER_ADDR, 1, 1, ®, 1);
|
|
debug("Retimer version id = 0x%x\n", reg);
|
|
|
|
/* Enable Broadcast. All writes target all channel register sets */
|
|
reg = 0x0c;
|
|
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
|
|
|
|
/* Reset Channel Registers */
|
|
i2c_read(I2C_RETIMER_ADDR, 0, 1, ®, 1);
|
|
reg |= 0x4;
|
|
i2c_write(I2C_RETIMER_ADDR, 0, 1, ®, 1);
|
|
|
|
/* Set data rate as 10.3125 Gbps */
|
|
reg = 0x90;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x60, 1, ®, 1);
|
|
reg = 0xb3;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x61, 1, ®, 1);
|
|
reg = 0x90;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x62, 1, ®, 1);
|
|
reg = 0xb3;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x63, 1, ®, 1);
|
|
reg = 0xcd;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x64, 1, ®, 1);
|
|
|
|
/* Select VCO Divider to full rate (000) */
|
|
i2c_read(I2C_RETIMER_ADDR, 0x2F, 1, ®, 1);
|
|
reg &= 0x0f;
|
|
reg |= 0x70;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x2F, 1, ®, 1);
|
|
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
/* Retimer is connected to I2C1_CH5 */
|
|
select_i2c_ch_pca9547(I2C_MUX_CH5);
|
|
|
|
/* Access to Control/Shared register */
|
|
reg = 0x0;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0xff, 1, ®, 1);
|
|
|
|
/* Read device revision and ID */
|
|
i2c_read(I2C_RETIMER_ADDR2, 1, 1, ®, 1);
|
|
debug("Retimer version id = 0x%x\n", reg);
|
|
|
|
/* Enable Broadcast. All writes target all channel register sets */
|
|
reg = 0x0c;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0xff, 1, ®, 1);
|
|
|
|
/* Reset Channel Registers */
|
|
i2c_read(I2C_RETIMER_ADDR2, 0, 1, ®, 1);
|
|
reg |= 0x4;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0, 1, ®, 1);
|
|
|
|
/* Set data rate as 10.3125 Gbps */
|
|
reg = 0x90;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x60, 1, ®, 1);
|
|
reg = 0xb3;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x61, 1, ®, 1);
|
|
reg = 0x90;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x62, 1, ®, 1);
|
|
reg = 0xb3;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x63, 1, ®, 1);
|
|
reg = 0xcd;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x64, 1, ®, 1);
|
|
|
|
/* Select VCO Divider to full rate (000) */
|
|
i2c_read(I2C_RETIMER_ADDR2, 0x2F, 1, ®, 1);
|
|
reg &= 0x0f;
|
|
reg |= 0x70;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x2F, 1, ®, 1);
|
|
#endif
|
|
/*return the default channel*/
|
|
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
init_final_memctl_regs();
|
|
#if defined(CONFIG_TARGET_LS1088ARDB) && defined(CONFIG_FSL_MC_ENET)
|
|
u32 __iomem *irq_ccsr = (u32 __iomem *)ISC_BASE;
|
|
#endif
|
|
|
|
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
|
|
board_retimer_init();
|
|
|
|
#ifdef CONFIG_ENV_IS_NOWHERE
|
|
gd->env_addr = (ulong)&default_environment[0];
|
|
#endif
|
|
|
|
#if defined(CONFIG_TARGET_LS1088ARDB) && defined(CONFIG_FSL_MC_ENET)
|
|
/* invert AQR105 IRQ pins polarity */
|
|
out_le32(irq_ccsr + IRQCR_OFFSET / 4, AQR105_IRQ_MASK);
|
|
#endif
|
|
|
|
#ifdef CONFIG_FSL_CAAM
|
|
sec_init();
|
|
#endif
|
|
#ifdef CONFIG_FSL_LS_PPA
|
|
ppa_init();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
fsl_lsch3_early_init_f();
|
|
return 0;
|
|
}
|
|
|
|
void detail_board_ddr_info(void)
|
|
{
|
|
puts("\nDDR ");
|
|
print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
|
|
print_ddr_info(0);
|
|
}
|
|
|
|
#if defined(CONFIG_ARCH_MISC_INIT)
|
|
int arch_misc_init(void)
|
|
{
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_FSL_MC_ENET
|
|
void fdt_fixup_board_enet(void *fdt)
|
|
{
|
|
int offset;
|
|
|
|
offset = fdt_path_offset(fdt, "/fsl-mc");
|
|
|
|
if (offset < 0)
|
|
offset = fdt_path_offset(fdt, "/fsl,dprc@0");
|
|
|
|
if (offset < 0) {
|
|
printf("%s: ERROR: fsl-mc node not found in device tree (error %d)\n",
|
|
__func__, offset);
|
|
return;
|
|
}
|
|
|
|
if (get_mc_boot_status() == 0)
|
|
fdt_status_okay(fdt, offset);
|
|
else
|
|
fdt_status_fail(fdt, offset);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_OF_BOARD_SETUP
|
|
void fsl_fdt_fixup_flash(void *fdt)
|
|
{
|
|
int offset;
|
|
|
|
/*
|
|
* IFC-NOR and QSPI are muxed on SoC.
|
|
* So disable IFC node in dts if QSPI is enabled or
|
|
* disable QSPI node in dts in case QSPI is not enabled.
|
|
*/
|
|
|
|
#ifdef CONFIG_FSL_QSPI
|
|
offset = fdt_path_offset(fdt, "/soc/ifc/nor");
|
|
|
|
if (offset < 0)
|
|
offset = fdt_path_offset(fdt, "/ifc/nor");
|
|
#else
|
|
offset = fdt_path_offset(fdt, "/soc/quadspi");
|
|
|
|
if (offset < 0)
|
|
offset = fdt_path_offset(fdt, "/quadspi");
|
|
#endif
|
|
if (offset < 0)
|
|
return;
|
|
|
|
fdt_status_disabled(fdt, offset);
|
|
}
|
|
|
|
int ft_board_setup(void *blob, bd_t *bd)
|
|
{
|
|
int err, i;
|
|
u64 base[CONFIG_NR_DRAM_BANKS];
|
|
u64 size[CONFIG_NR_DRAM_BANKS];
|
|
|
|
ft_cpu_setup(blob, bd);
|
|
|
|
/* fixup DT for the two GPP DDR banks */
|
|
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
|
|
base[i] = gd->bd->bi_dram[i].start;
|
|
size[i] = gd->bd->bi_dram[i].size;
|
|
}
|
|
|
|
#ifdef CONFIG_RESV_RAM
|
|
/* reduce size if reserved memory is within this bank */
|
|
if (gd->arch.resv_ram >= base[0] &&
|
|
gd->arch.resv_ram < base[0] + size[0])
|
|
size[0] = gd->arch.resv_ram - base[0];
|
|
else if (gd->arch.resv_ram >= base[1] &&
|
|
gd->arch.resv_ram < base[1] + size[1])
|
|
size[1] = gd->arch.resv_ram - base[1];
|
|
#endif
|
|
|
|
fdt_fixup_memory_banks(blob, base, size, CONFIG_NR_DRAM_BANKS);
|
|
|
|
fsl_fdt_fixup_flash(blob);
|
|
|
|
#ifdef CONFIG_FSL_MC_ENET
|
|
fdt_fixup_board_enet(blob);
|
|
err = fsl_mc_ldpaa_exit(bd);
|
|
if (err)
|
|
return err;
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|