upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/include/configs/cam_enc_4xx.h

505 lines
16 KiB

/*
* Copyright (C) 2009 Texas Instruments Incorporated
*
* Copyright (C) 2011
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
#define CONFIG_SYS_CONSOLE_INFO_QUIET
/* SoC Configuration */
#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
#define CONFIG_SYS_HZ_CLOCK 24000000 /* timer0 freq */
#define CONFIG_SOC_DM365
#define CONFIG_MACH_TYPE MACH_TYPE_DAVINCI_DM365_EVM
#define CONFIG_HOSTNAME cam_enc_4xx
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_CAM_ENC_LED_MASK 0x0fc00000
/* Memory Info */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x80000000
#define PHYS_SDRAM_1_SIZE (256 << 20) /* 256 MiB */
#define DDR_4BANKS /* 4-bank DDR2 (256MB) */
#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
/* Serial Driver info: UART0 for console */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE -4
#define CONFIG_SYS_NS16550_COM1 0x01c20000
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
/* Network Configuration */
#define CONFIG_DRIVER_TI_EMAC
#define CONFIG_EMAC_MDIO_PHY_NUM 0
#define CONFIG_SYS_EMAC_TI_CLKDIV 0xa9 /* 1MHz */
#define CONFIG_MII
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
#define CONFIG_CMD_MII
#define CONFIG_SYS_DCACHE_OFF
#define CONFIG_RESET_PHY_R
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_DAVINCI
#define CONFIG_SYS_DAVINCI_I2C_SPEED 400000
#define CONFIG_SYS_DAVINCI_I2C_SLAVE 0x10 /* SMBus host address */
/* NAND: socketed, two chipselects, normally 2 GBytes */
#define CONFIG_NAND_DAVINCI
#define CONFIG_SYS_NAND_CS 2
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
#define CONFIG_SYS_NAND_PAGE_2K
#define CONFIG_SYS_NAND_LARGEPAGE
#define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, }
/* socket has two chipselects, nCE0 gated by address BIT(14) */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
/* SPI support */
#define CONFIG_SPI
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_DAVINCI_SPI
#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE
#define CONFIG_SYS_SPI_CLK davinci_clk_get(SPI_PLLDIV)
#define CONFIG_SF_DEFAULT_SPEED 3000000
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#define CONFIG_CMD_SF
/* SD/MMC */
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_DAVINCI_MMC
#define CONFIG_MMC_MBLOCK
/* U-Boot command configuration */
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_I2C
#define CONFIG_CMD_PING
#define CONFIG_CMD_SAVES
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#ifdef CONFIG_MMC
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_MMC
#endif
#ifdef CONFIG_NAND_DAVINCI
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_PARTITIONS
#define CONFIG_MTD_DEVICE
#define CONFIG_CMD_NAND
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_RBTREE
#define CONFIG_LZO
#endif
#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
/* U-Boot general configuration */
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
#define CONFIG_SYS_PROMPT "cam_enc_4xx> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE /* Print buffer size */ \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_LONGHELP
#define CONFIG_MENU
#define CONFIG_MENU_SHOW
#define CONFIG_FIT
#define CONFIG_BOARD_IMG_ADDR_R 0x80000000
#ifdef CONFIG_NAND_DAVINCI
#define CONFIG_ENV_SIZE (16 << 10)
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0x180000
#define CONFIG_ENV_RANGE 0x040000
#define CONFIG_ENV_OFFSET_REDUND 0x1c0000
#undef CONFIG_ENV_IS_IN_FLASH
#endif
#if defined(CONFIG_MMC) && !defined(CONFIG_ENV_IS_IN_NAND)
#define CONFIG_CMD_ENV
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
#define CONFIG_ENV_OFFSET (51 << 9) /* Sector 51 */
#define CONFIG_ENV_IS_IN_MMC
#undef CONFIG_ENV_IS_IN_FLASH
#endif
#define CONFIG_BOOTDELAY 3
/*
* 24MHz InputClock / 15 prediv -> 1.6 MHz timer running
* Timeout 1 second.
*/
#define CONFIG_AIT_TIMER_TIMEOUT 0x186a00
#define CONFIG_CMDLINE_EDITING
#define CONFIG_VERSION_VARIABLE
#define CONFIG_TIMESTAMP
/* U-Boot memory configuration */
#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* 1 MiB */
#define CONFIG_SYS_MEMTEST_START 0x80000000 /* physical address */
#define CONFIG_SYS_MEMTEST_END 0x81000000 /* test 16MB RAM */
/* Linux interfacing */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_SYS_BARGSIZE 1024 /* bootarg Size */
#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* kernel address */
#define MTDIDS_DEFAULT "nand0=davinci_nand.0"
#define MTDPARTS_DEFAULT \
"mtdparts=" \
"davinci_nand.0:" \
"128k(spl)," \
"384k(UBLheader)," \
"1m(u-boot)," \
"512k(env)," \
"-(ubi)"
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_NAND_SIMPLE
#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_POST_MEM_SUPPORT
#define CONFIG_SPL_LDSCRIPT "$(BOARDDIR)/u-boot-spl.lds"
#define CONFIG_SPL_STACK (0x00010000 + 0x7f00)
#define CONFIG_SPL_TEXT_BASE 0x00000020 /*CONFIG_SYS_SRAM_START*/
/* Provide at least 16MB spacing between us and the Linux Kernel image */
#define CONFIG_SPL_PAD_TO 12320
#define CONFIG_SPL_MAX_FOOTPRINT 12288
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_TEXT_BASE 0x81080000
#endif
#define CONFIG_SYS_NAND_BASE 0x02000000
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
CONFIG_SYS_NAND_PAGE_SIZE)
#define CONFIG_SYS_NAND_ECCPOS { \
24, 25, 26, 27, 28, \
29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
59, 60, 61, 62, 63 }
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
#define CONFIG_SYS_NAND_ECCSIZE 0x200
#define CONFIG_SYS_NAND_ECCBYTES 10
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
/*
* RBL searches from Block n (n = 1..24)
* so we can define, how many UBL Headers
* we can write before the real spl code
*/
#define CONFIG_SYS_NROF_PAGES_NAND_SPL 6
#define CONFIG_SYS_NAND_U_BOOT_DST 0x81080000 /* u-boot TEXT_BASE */
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
/*
* Post tests for memory testing
*/
#define CONFIG_POST CONFIG_SYS_POST_MEMORY
#define _POST_WORD_ADDR 0x0
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_STACK
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0xa0000
#define CONFIG_SYS_NAND_U_BOOT_ERA_SIZE 0x100000
/* for UBL header */
#define CONFIG_SYS_UBL_BLOCK (CONFIG_SYS_NAND_PAGE_SIZE)
#define CONFIG_SYS_DM36x_PLL1_PLLM 0x55
#define CONFIG_SYS_DM36x_PLL1_PREDIV 0x8005
#define CONFIG_SYS_DM36x_PLL2_PLLM 0x09
#define CONFIG_SYS_DM36x_PLL2_PREDIV 0x8000
#define CONFIG_SYS_DM36x_PERI_CLK_CTRL 0x243F04FC
#define CONFIG_SYS_DM36x_PLL1_PLLDIV1 0x801b
#define CONFIG_SYS_DM36x_PLL1_PLLDIV2 0x8001
/* POST DIV 680/2 = 340Mhz -> MJCP and HDVICP bus interface clock */
#define CONFIG_SYS_DM36x_PLL1_PLLDIV3 0x8001
/*
* POST DIV 680/4 = 170Mhz -> EDMA/Peripheral CFG0(1/2 MJCP/HDVICP bus
* interface clk)
*/
#define CONFIG_SYS_DM36x_PLL1_PLLDIV4 0x8003
/* POST DIV 680/2 = 340Mhz -> VPSS */
#define CONFIG_SYS_DM36x_PLL1_PLLDIV5 0x8001
/* POST DIV 680/9 = 75.6 Mhz -> VENC */
#define CONFIG_SYS_DM36x_PLL1_PLLDIV6 0x8008
/*
* POST DIV 680/1 = 680Mhz -> DDRx2(with internal divider of 2, clock boils
* down to 340 Mhz)
*/
#define CONFIG_SYS_DM36x_PLL1_PLLDIV7 0x8000
/* POST DIV 680/7= 97Mhz-> MMC0/SD0 */
#define CONFIG_SYS_DM36x_PLL1_PLLDIV8 0x8006
/* POST DIV 680/28 = 24.3Mhz-> CLKOUT */
#define CONFIG_SYS_DM36x_PLL1_PLLDIV9 0x801b
#define CONFIG_SYS_DM36x_PLL2_PLLDIV1 0x8011
/* POST DIV 432/1=432 Mhz -> ARM926/(HDVICP block) clk */
#define CONFIG_SYS_DM36x_PLL2_PLLDIV2 0x8000
#define CONFIG_SYS_DM36x_PLL2_PLLDIV3 0x8001
/* POST DIV 432/21= 20.5714 Mhz->VOICE Codec clk */
#define CONFIG_SYS_DM36x_PLL2_PLLDIV4 0x8014
/* POST DIV 432/16=27 Mhz -> VENC(For SD modes, requires) */
#define CONFIG_SYS_DM36x_PLL2_PLLDIV5 0x800f
/*
* READ LATENCY 7 (CL + 2)
* CONFIG_PWRDNEN = 1
* CONFIG_EXT_STRBEN = 1
*/
#define CONFIG_SYS_DM36x_DDR2_DDRPHYCR (0 \
| DV_DDR_PHY_EXT_STRBEN \
| DV_DDR_PHY_PWRDNEN \
| (7 << DV_DDR_PHY_RD_LATENCY_SHIFT))
/*
* T_RFC = (trfc/DDR_CLK) - 1 = (195 / 2.941) - 1
* T_RP = (trp/DDR_CLK) - 1 = (12.5 / 2.941) - 1
* T_RCD = (trcd/DDR_CLK) - 1 = (12.5 / 2.941) - 1
* T_WR = (twr/DDR_CLK) - 1 = (15 / 2.941) - 1
* T_RAS = (tras/DDR_CLK) - 1 = (45 / 2.941) - 1
* T_RC = (trc/DDR_CLK) - 1 = (57.5 / 2.941) - 1
* T_RRD = (trrd/DDR_CLK) - 1 = (7.5 / 2.941) - 1
* T_WTR = (twtr/DDR_CLK) - 1 = (7.5 / 2.941) - 1
*/
#define CONFIG_SYS_DM36x_DDR2_SDTIMR (0 \
| (66 << DV_DDR_SDTMR1_RFC_SHIFT) \
| (4 << DV_DDR_SDTMR1_RP_SHIFT) \
| (4 << DV_DDR_SDTMR1_RCD_SHIFT) \
| (5 << DV_DDR_SDTMR1_WR_SHIFT) \
| (14 << DV_DDR_SDTMR1_RAS_SHIFT) \
| (19 << DV_DDR_SDTMR1_RC_SHIFT) \
| (2 << DV_DDR_SDTMR1_RRD_SHIFT) \
| (2 << DV_DDR_SDTMR1_WTR_SHIFT))
/*
* T_RASMAX = (trasmax/refresh_rate) - 1 = (70K / 7812.6) - 1
* T_XP = tCKE - 1 = 3 - 2
* T_XSNR= ((trfc + 10)/DDR_CLK) - 1 = (205 / 2.941) - 1
* T_XSRD = txsrd - 1 = 200 - 1
* T_RTP = (trtp/DDR_CLK) - 1 = (7.5 / 2.941) - 1
* T_CKE = tcke - 1 = 3 - 1
*/
#define CONFIG_SYS_DM36x_DDR2_SDTIMR2 (0 \
| (8 << DV_DDR_SDTMR2_RASMAX_SHIFT) \
| (2 << DV_DDR_SDTMR2_XP_SHIFT) \
| (69 << DV_DDR_SDTMR2_XSNR_SHIFT) \
| (199 << DV_DDR_SDTMR2_XSRD_SHIFT) \
| (2 << DV_DDR_SDTMR2_RTP_SHIFT) \
| (2 << DV_DDR_SDTMR2_CKE_SHIFT))
/* PR_OLD_COUNT = 0xfe */
#define CONFIG_SYS_DM36x_DDR2_PBBPR 0x000000FE
/* refresh rate = 0x768 */
#define CONFIG_SYS_DM36x_DDR2_SDRCR 0x00000768
#define CONFIG_SYS_DM36x_DDR2_SDBCR (0 \
| (2 << DV_DDR_SDCR_PAGESIZE_SHIFT) \
| (3 << DV_DDR_SDCR_IBANK_SHIFT) \
| (5 << DV_DDR_SDCR_CL_SHIFT) \
| (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) \
| (1 << DV_DDR_SDCR_TIMUNLOCK_SHIFT) \
| (1 << DV_DDR_SDCR_DDREN_SHIFT) \
| (0 << DV_DDR_SDCR_DDRDRIVE0_SHIFT) \
| (1 << DV_DDR_SDCR_DDR2EN_SHIFT) \
| (1 << DV_DDR_SDCR_DDR_DDQS_SHIFT) \
| (1 << DV_DDR_SDCR_BOOTUNLOCK_SHIFT))
#define CONFIG_SYS_DM36x_AWCCR 0xff
#define CONFIG_SYS_DM36x_AB1CR 0x40400204
#define CONFIG_SYS_DM36x_AB2CR 0x04ca2650
/* All Video Inputs */
#define CONFIG_SYS_DM36x_PINMUX0 0x00000000
/*
* All Video Outputs,
* GPIO 86, 87 + 90 0x0000f030
*/
#define CONFIG_SYS_DM36x_PINMUX1 0x00530002
#define CONFIG_SYS_DM36x_PINMUX2 0x00001815
/*
* SPI1, UART1, I2C, SD0, SD1, McBSP0, CLKOUTs
* GPIO 25 0x60000000
*/
#define CONFIG_SYS_DM36x_PINMUX3 0x9b5affff
/*
* MMC/SD0 instead of MS, SPI0
* GPIO 34 0x0000c000
*/
#define CONFIG_SYS_DM36x_PINMUX4 0x00002655
/*
* Default environment settings
*/
#define DVN4XX_UBOOT_ADDR_R_RAM 0x80000000
/* (DVN4XX_UBOOT_ADDR_R_RAM + CONFIG_SYS_NAND_PAGE_SIZE) */
#define DVN4XX_UBOOT_ADDR_R_NAND_SPL 0x80000800
/*
* (DVN4XX_UBOOT_ADDR_R_NAND_SPL + (CONFIG_SYS_NROF_PAGES_NAND_SPL * \
* CONFIG_SYS_NAND_PAGE_SIZE))
*/
#define DVN4XX_UBOOT_ADDR_R_UBOOT 0x80003800
#define CONFIG_EXTRA_ENV_SETTINGS \
"u_boot_addr_r=" __stringify(DVN4XX_UBOOT_ADDR_R_RAM) "\0" \
"u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.ubl\0" \
"load=tftp ${u_boot_addr_r} ${u-boot}\0" \
"pagesz=" __stringify(CONFIG_SYS_NAND_PAGE_SIZE) "\0" \
"writeheader=nandrbl rbl;nand erase 20000 ${pagesz};" \
"nand write ${u_boot_addr_r} 20000 ${pagesz};" \
"nandrbl uboot\0" \
"writenand_spl=nandrbl rbl;nand erase 0 3000;" \
"nand write " __stringify(DVN4XX_UBOOT_ADDR_R_NAND_SPL) \
" 0 3000;nandrbl uboot\0" \
"writeuboot=nandrbl uboot;" \
"nand erase " __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " "\
__stringify(CONFIG_SYS_NAND_U_BOOT_ERA_SIZE) \
";nand write " __stringify(DVN4XX_UBOOT_ADDR_R_UBOOT) \
" " __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " " \
__stringify(CONFIG_SYS_NAND_U_BOOT_SIZE) "\0" \
"update=run load writenand_spl writeuboot\0" \
"bootcmd=run net_nfs\0" \
"rootpath=/opt/eldk-arm/arm\0" \
"mtdids=" MTDIDS_DEFAULT "\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
"netdev=eth0\0" \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"addmisc=setenv bootargs ${bootargs} app_reset=${app_reset}\0" \
"addcon=setenv bootargs ${bootargs} console=ttyS0," \
"${baudrate}n8\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off eth=${ethaddr} panic=1\0" \
"rootpath=/opt/eldk-arm/arm\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage \0" \
"kernel_addr_r=80600000\0" \
"load_kernel=tftp ${kernel_addr_r} ${bootfile}\0" \
"ubi_load_kernel=ubi part ubi 2048;ubifsmount ubi:${img_volume};" \
"ubifsload ${kernel_addr_r} boot/uImage\0" \
"fit_addr_r=" __stringify(CONFIG_BOARD_IMG_ADDR_R) "\0" \
"img_addr_r=" __stringify(CONFIG_BOARD_IMG_ADDR_R) "\0" \
"img_file=" __stringify(CONFIG_HOSTNAME) "/ait.itb\0" \
"header_addr=20000\0" \
"img_writeheader=nandrbl rbl;" \
"nand erase ${header_addr} ${pagesz};" \
"nand write ${img_addr_r} ${header_addr} ${pagesz};" \
"nandrbl uboot\0" \
"img_writespl=nandrbl rbl;nand erase 0 3000;" \
"nand write ${img_addr_r} 0 3000;nandrbl uboot\0" \
"img_writeuboot=nandrbl uboot;" \
"nand erase " __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " "\
__stringify(CONFIG_SYS_NAND_U_BOOT_ERA_SIZE) \
";nand write ${img_addr_r} " \
__stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " " \
__stringify(CONFIG_SYS_NAND_U_BOOT_SIZE) "\0" \
"img_writedfenv=ubi part ubi 2048;" \
"ubi write ${img_addr_r} default ${filesize}\0" \
"img_volume=rootfs1\0" \
"img_writeramdisk=ubi part ubi 2048;" \
"ubi write ${img_addr_r} ${img_volume} ${filesize}\0" \
"load_img=tftp ${fit_addr_r} ${img_file}\0" \
"net_nfs=run load_kernel; " \
"run nfsargs addip addcon addmtd addmisc;" \
"bootm ${kernel_addr_r}\0" \
"ubi_ubi=run ubi_load_kernel; " \
"run ubiargs addip addcon addmtd addmisc;" \
"bootm ${kernel_addr_r}\0" \
"ubiargs=setenv bootargs ubi.mtd=4,2048" \
" root=ubi0:${img_volume} rw rootfstype=ubifs\0" \
"app_reset=no\0" \
"dvn_app_vers=void\0" \
"dvn_boot_vers=void\0" \
"savenewvers=run savetmpparms restoreparms; saveenv;" \
"run restoretmpparms\0" \
"savetmpparms=setenv y_ipaddr ${ipaddr};" \
"setenv y_netmask ${netmask};" \
"setenv y_serverip ${serverip};" \
"setenv y_gatewayip ${gatewayip}\0" \
"saveparms=setenv x_ipaddr ${ipaddr};" \
"setenv x_netmask ${netmask};" \
"setenv x_serverip ${serverip};" \
"setenv x_gatewayip ${gatewayip}\0" \
"restoreparms=setenv ipaddr ${x_ipaddr};" \
"setenv netmask ${x_netmask};" \
"setenv serverip ${x_serverip};" \
"setenv gatewayip ${x_gatewayip}\0" \
"restoretmpparms=setenv ipaddr ${y_ipaddr};" \
"setenv netmask ${y_netmask};" \
"setenv serverip ${y_serverip};" \
"setenv gatewayip ${y_gatewayip}\0" \
"\0"
/* USB Configuration */
#define CONFIG_USB_DAVINCI
#define CONFIG_MUSB_HCD
#define CONFIG_DV_USBPHY_CTL (USBPHY_SESNDEN | USBPHY_VBDTCTEN | \
USBPHY_PHY24MHZ)
#define CONFIG_CMD_USB /* include support for usb cmd */
#define CONFIG_USB_STORAGE /* MSC class support */
#define CONFIG_CMD_STORAGE /* inclue support for usb-storage cmd */
#define CONFIG_CMD_FAT /* inclue support for FAT/storage */
#define CONFIG_DOS_PARTITION /* inclue support for FAT/storage */
#undef DAVINCI_DM365EVM
#define PINMUX4_USBDRVBUS_BITCLEAR 0x3000
#define PINMUX4_USBDRVBUS_BITSET 0x2000
#endif /* __CONFIG_H */