upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/siemens/CCM/ccm.c

440 lines
11 KiB

/*
* (C) Copyright 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <mpc8xx.h>
#include <commproc.h>
#include <command.h>
/* ------------------------------------------------------------------------- */
static long int dram_size (long int, long int *, long int);
void can_driver_enable (void);
void can_driver_disable (void);
int fpga_init(void);
/* ------------------------------------------------------------------------- */
#define _NOT_USED_ 0xFFFFFFFF
const uint sdram_table[] =
{
/*
* Single Read. (Offset 0 in UPMA RAM)
*/
0x1F0DFC04, 0xEEAFBC04, 0x11AF7C04, 0xEFBAFC00,
0x1FF5FC47, /* last */
/*
* SDRAM Initialization (offset 5 in UPMA RAM)
*
* This is no UPM entry point. The following definition uses
* the remaining space to establish an initialization
* sequence, which is executed by a RUN command.
*
*/
0x1FF5FC34, 0xEFEABC34, 0x1FB57C35, /* last */
/*
* Burst Read. (Offset 8 in UPMA RAM)
*/
0x1F0DFC04, 0xEEAFBC04, 0x10AF7C04, 0xF0AFFC00,
0xF0AFFC00, 0xF1AFFC00, 0xEFBAFC00, 0x1FF5FC47, /* last */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Single Write. (Offset 18 in UPMA RAM)
*/
0x1F0DFC04, 0xEEABBC00, 0x01B27C04, 0x1FF5FC47, /* last */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Burst Write. (Offset 20 in UPMA RAM)
*/
0x1F0DFC04, 0xEEABBC00, 0x10A77C00, 0xF0AFFC00,
0xF0AFFC00, 0xE1BAFC04, 0x1FF5FC47, /* last */
_NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Refresh (Offset 30 in UPMA RAM)
*/
0x1FFD7C84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
0xFFFFFC84, 0xFFFFFC07, /* last */
_NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Exception. (Offset 3c in UPMA RAM)
*/
0x7FFFFC07, /* last */
_NOT_USED_, _NOT_USED_, _NOT_USED_,
};
/* ------------------------------------------------------------------------- */
/*
* Check Board Identity:
*
* Always return 1 (no second DRAM bank since based on TQM8xxL module)
*/
int checkboard (void)
{
unsigned char *s;
unsigned char buf[64];
s = (getenv_r ("serial#", buf, sizeof(buf)) > 0) ? buf : NULL;
puts ("Board: Siemens CCM");
if (s) {
puts (" (");
for (; *s; ++s) {
if (*s == ' ')
break;
putc (*s);
}
putc (')');
}
putc ('\n');
return (0);
}
/* ------------------------------------------------------------------------- */
/*
* If Power-On-Reset switch off the Red and Green LED: At reset, the
* data direction registers are cleared and must therefore be restored.
*/
#define RSR_CSRS 0x08000000
int power_on_reset(void)
{
/* Test Reset Status Register */
return ((volatile immap_t *)CFG_IMMR)->im_clkrst.car_rsr & RSR_CSRS ? 0:1;
}
#define PB_LED_GREEN 0x10000 /* red LED is on PB.15 */
#define PB_LED_RED 0x20000 /* red LED is on PB.14 */
#define PB_LEDS (PB_LED_GREEN | PB_LED_RED);
static void init_leds (void)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
immap->im_cpm.cp_pbpar &= ~PB_LEDS;
immap->im_cpm.cp_pbodr &= ~PB_LEDS;
immap->im_cpm.cp_pbdir |= PB_LEDS;
/* Check stop reset status */
if (power_on_reset()) {
immap->im_cpm.cp_pbdat &= ~PB_LEDS;
}
}
/* ------------------------------------------------------------------------- */
long int initdram (int board_type)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size8, size9;
long int size = 0;
unsigned long reg;
upmconfig(UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
/*
* Preliminary prescaler for refresh (depends on number of
* banks): This value is selected for four cycles every 62.4 us
* with two SDRAM banks or four cycles every 31.2 us with one
* bank. It will be adjusted after memory sizing.
*/
memctl->memc_mptpr = CFG_MPTPR_2BK_8K;
memctl->memc_mar = 0x00000088;
/*
* Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at
* preliminary addresses - these have to be modified after the
* SDRAM size has been determined.
*/
memctl->memc_or2 = CFG_OR2_PRELIM;
memctl->memc_br2 = CFG_BR2_PRELIM;
memctl->memc_mamr = CFG_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
udelay(200);
/* perform SDRAM initializsation sequence */
memctl->memc_mcr = 0x80004105; /* SDRAM bank 0 */
udelay(1);
memctl->memc_mcr = 0x80004230; /* SDRAM bank 0 - execute twice */
udelay(1);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay (1000);
/*
* Check Bank 0 Memory Size for re-configuration
*
* try 8 column mode
*/
size8 = dram_size (CFG_MAMR_8COL, (ulong *)SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
udelay (1000);
/*
* try 9 column mode
*/
size9 = dram_size (CFG_MAMR_9COL, (ulong *)SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
size = size9;
/* debug ("SDRAM in 9 column mode: %ld MB\n", size >> 20); */
} else { /* back to 8 columns */
size = size8;
memctl->memc_mamr = CFG_MAMR_8COL;
udelay(500);
/* debug ("SDRAM in 8 column mode: %ld MB\n", size >> 20); */
}
udelay (1000);
/*
* Adjust refresh rate depending on SDRAM type
* For types > 128 MBit leave it at the current (fast) rate
*/
if (size < 0x02000000) {
/* reduce to 15.6 us (62.4 us / quad) */
memctl->memc_mptpr = CFG_MPTPR_2BK_4K;
udelay(1000);
}
/*
* Final mapping
*/
memctl->memc_or2 = ((-size) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM;
memctl->memc_br2 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
/* adjust refresh rate depending on SDRAM type, one bank */
reg = memctl->memc_mptpr;
reg >>= 1; /* reduce to CFG_MPTPR_1BK_8K / _4K */
memctl->memc_mptpr = reg;
can_driver_enable ();
init_leds ();
udelay(10000);
return (size);
}
/* ------------------------------------------------------------------------- */
/*
* Warning - both the PUMA load mode and the CAN driver use UPM B,
* so make sure only one of both is active.
*/
void can_driver_enable (void)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
/* Initialize MBMR */
memctl->memc_mbmr = MAMR_GPL_B4DIS; /* GPL_B4 ouput line Disable */
/* Initialize UPMB for CAN: single read */
memctl->memc_mdr = 0xFFFFC004;
memctl->memc_mcr = 0x0100 | UPMB;
memctl->memc_mdr = 0x0FFFD004;
memctl->memc_mcr = 0x0101 | UPMB;
memctl->memc_mdr = 0x0FFFC000;
memctl->memc_mcr = 0x0102 | UPMB;
memctl->memc_mdr = 0x3FFFC004;
memctl->memc_mcr = 0x0103 | UPMB;
memctl->memc_mdr = 0xFFFFDC05;
memctl->memc_mcr = 0x0104 | UPMB;
/* Initialize UPMB for CAN: single write */
memctl->memc_mdr = 0xFFFCC004;
memctl->memc_mcr = 0x0118 | UPMB;
memctl->memc_mdr = 0xCFFCD004;
memctl->memc_mcr = 0x0119 | UPMB;
memctl->memc_mdr = 0x0FFCC000;
memctl->memc_mcr = 0x011A | UPMB;
memctl->memc_mdr = 0x7FFCC004;
memctl->memc_mcr = 0x011B | UPMB;
memctl->memc_mdr = 0xFFFDCC05;
memctl->memc_mcr = 0x011C | UPMB;
/* Initialize OR3 / BR3 for CAN Bus Controller */
memctl->memc_or3 = CFG_OR3_CAN;
memctl->memc_br3 = CFG_BR3_CAN;
}
void can_driver_disable (void)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
/* Reset OR3 / BR3 to disable CAN Bus Controller */
memctl->memc_br3 = 0;
memctl->memc_or3 = 0;
memctl->memc_mbmr = 0;
}
/* ------------------------------------------------------------------------- */
/*
* Check memory range for valid RAM. A simple memory test determines
* the actually available RAM size between addresses `base' and
* `base + maxsize'. Some (not all) hardware errors are detected:
* - short between address lines
* - short between data lines
*/
static long int dram_size (long int mamr_value, long int *base, long int maxsize)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
volatile long int *addr;
ulong cnt, val;
ulong save[32]; /* to make test non-destructive */
unsigned char i = 0;
memctl->memc_mamr = mamr_value;
for (cnt = maxsize/sizeof(long); cnt > 0; cnt >>= 1) {
addr = base + cnt; /* pointer arith! */
save[i++] = *addr;
*addr = ~cnt;
}
/* write 0 to base address */
addr = base;
save[i] = *addr;
*addr = 0;
/* check at base address */
if ((val = *addr) != 0) {
*addr = save[i];
return (0);
}
for (cnt = 1; cnt <= maxsize/sizeof(long); cnt <<= 1) {
addr = base + cnt; /* pointer arith! */
val = *addr;
*addr = save[--i];
if (val != (~cnt)) {
return (cnt * sizeof(long));
}
}
return (maxsize);
}
/* ------------------------------------------------------------------------- */
#define ETH_CFG_BITS (CFG_PB_ETH_CFG1 | CFG_PB_ETH_CFG2 | CFG_PB_ETH_CFG3 )
#define ETH_ALL_BITS (ETH_CFG_BITS | CFG_PB_ETH_POWERDOWN)
void reset_phy(void)
{
immap_t *immr = (immap_t *)CFG_IMMR;
ulong value;
/* Configure all needed port pins for GPIO */
#if CFG_ETH_MDDIS_VALUE
immr->im_ioport.iop_padat |= CFG_PA_ETH_MDDIS;
#else
immr->im_ioport.iop_padat &= ~(CFG_PA_ETH_MDDIS | CFG_PA_ETH_RESET); /* Set low */
#endif
immr->im_ioport.iop_papar &= ~(CFG_PA_ETH_MDDIS | CFG_PA_ETH_RESET); /* GPIO */
immr->im_ioport.iop_paodr &= ~(CFG_PA_ETH_MDDIS | CFG_PA_ETH_RESET); /* active output */
immr->im_ioport.iop_padir |= CFG_PA_ETH_MDDIS | CFG_PA_ETH_RESET; /* output */
immr->im_cpm.cp_pbpar &= ~(ETH_ALL_BITS); /* GPIO */
immr->im_cpm.cp_pbodr &= ~(ETH_ALL_BITS); /* active output */
value = immr->im_cpm.cp_pbdat;
/* Assert Powerdown and Reset signals */
value |= CFG_PB_ETH_POWERDOWN;
/* PHY configuration includes MDDIS and CFG1 ... CFG3 */
#if CFG_ETH_CFG1_VALUE
value |= CFG_PB_ETH_CFG1;
#else
value &= ~(CFG_PB_ETH_CFG1);
#endif
#if CFG_ETH_CFG2_VALUE
value |= CFG_PB_ETH_CFG2;
#else
value &= ~(CFG_PB_ETH_CFG2);
#endif
#if CFG_ETH_CFG3_VALUE
value |= CFG_PB_ETH_CFG3;
#else
value &= ~(CFG_PB_ETH_CFG3);
#endif
/* Drive output signals to initial state */
immr->im_cpm.cp_pbdat = value;
immr->im_cpm.cp_pbdir |= ETH_ALL_BITS;
udelay (10000);
/* De-assert Ethernet Powerdown */
immr->im_cpm.cp_pbdat &= ~(CFG_PB_ETH_POWERDOWN); /* Enable PHY power */
udelay (10000);
/* de-assert RESET signal of PHY */
immr->im_ioport.iop_padat |= CFG_PA_ETH_RESET;
udelay (1000);
}
int misc_init_r (void)
{
fpga_init();
return (0);
}
/* ------------------------------------------------------------------------- */