upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
477 lines
12 KiB
477 lines
12 KiB
/*
|
|
* (C) Copyright 2003-2004
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* (C) Copyright 2004
|
|
* Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
|
|
*
|
|
* (C) Copyright 2006
|
|
* MicroSys GmbH
|
|
*
|
|
* Copyright 2012-2013 Stefan Roese <sr@denx.de>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <mpc5xxx.h>
|
|
#include <pci.h>
|
|
#include <miiphy.h>
|
|
#include <linux/compiler.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/io.h>
|
|
|
|
#ifdef CONFIG_A4M2K
|
|
#include "is46r16320d.h"
|
|
#else
|
|
#include "mt46v16m16-75.h"
|
|
#endif
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#if !defined(CONFIG_SYS_RAMBOOT) && \
|
|
(defined(CONFIG_SPL) && defined(CONFIG_SPL_BUILD))
|
|
static void sdram_start(int hi_addr)
|
|
{
|
|
long hi_addr_bit = hi_addr ? 0x01000000 : 0;
|
|
long control = SDRAM_CONTROL | hi_addr_bit;
|
|
|
|
/* unlock mode register */
|
|
out_be32((void *)MPC5XXX_SDRAM_CTRL, control | 0x80000000);
|
|
|
|
/* precharge all banks */
|
|
out_be32((void *)MPC5XXX_SDRAM_CTRL, control | 0x80000002);
|
|
|
|
#ifdef SDRAM_DDR
|
|
/* set mode register: extended mode */
|
|
out_be32((void *)MPC5XXX_SDRAM_MODE, SDRAM_EMODE);
|
|
|
|
/* set mode register: reset DLL */
|
|
out_be32((void *)MPC5XXX_SDRAM_MODE, SDRAM_MODE | 0x04000000);
|
|
#endif
|
|
|
|
/* precharge all banks */
|
|
out_be32((void *)MPC5XXX_SDRAM_CTRL, control | 0x80000002);
|
|
|
|
/* auto refresh */
|
|
out_be32((void *)MPC5XXX_SDRAM_CTRL, control | 0x80000004);
|
|
|
|
/* set mode register */
|
|
out_be32((void *)MPC5XXX_SDRAM_MODE, SDRAM_MODE);
|
|
|
|
/* normal operation */
|
|
out_be32((void *)MPC5XXX_SDRAM_CTRL, control);
|
|
|
|
/*
|
|
* Wait a short while for the DLL to lock before accessing
|
|
* the SDRAM
|
|
*/
|
|
udelay(100);
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* ATTENTION: Although partially referenced initdram does NOT make real use
|
|
* use of CONFIG_SYS_SDRAM_BASE. The code does not work if
|
|
* CONFIG_SYS_SDRAM_BASE is something else than 0x00000000.
|
|
*/
|
|
phys_size_t initdram(int board_type)
|
|
{
|
|
ulong dramsize = 0;
|
|
ulong dramsize2 = 0;
|
|
uint svr, pvr;
|
|
#if !defined(CONFIG_SYS_RAMBOOT) && \
|
|
(defined(CONFIG_SPL) && defined(CONFIG_SPL_BUILD))
|
|
ulong test1, test2;
|
|
|
|
/* setup SDRAM chip selects */
|
|
out_be32((void *)MPC5XXX_SDRAM_CS0CFG, 0x0000001e); /* 2GB at 0x0 */
|
|
out_be32((void *)MPC5XXX_SDRAM_CS1CFG, 0x80000000); /* disabled */
|
|
|
|
/* setup config registers */
|
|
out_be32((void *)MPC5XXX_SDRAM_CONFIG1, SDRAM_CONFIG1);
|
|
out_be32((void *)MPC5XXX_SDRAM_CONFIG2, SDRAM_CONFIG2);
|
|
|
|
#ifdef SDRAM_DDR
|
|
/* set tap delay */
|
|
out_be32((void *)MPC5XXX_CDM_PORCFG, SDRAM_TAPDELAY);
|
|
#endif
|
|
|
|
/* find RAM size using SDRAM CS0 only */
|
|
sdram_start(0);
|
|
test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
|
|
sdram_start(1);
|
|
test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
|
|
if (test1 > test2) {
|
|
sdram_start(0);
|
|
dramsize = test1;
|
|
} else {
|
|
dramsize = test2;
|
|
}
|
|
|
|
/* memory smaller than 1MB is impossible */
|
|
if (dramsize < (1 << 20))
|
|
dramsize = 0;
|
|
|
|
/* set SDRAM CS0 size according to the amount of RAM found */
|
|
if (dramsize > 0) {
|
|
out_be32((void *)MPC5XXX_SDRAM_CS0CFG,
|
|
0x13 + __builtin_ffs(dramsize >> 20) - 1);
|
|
} else {
|
|
out_be32((void *)MPC5XXX_SDRAM_CS0CFG, 0); /* disabled */
|
|
}
|
|
#else /* CONFIG_SYS_RAMBOOT */
|
|
|
|
/* retrieve size of memory connected to SDRAM CS0 */
|
|
dramsize = in_be32((void *)MPC5XXX_SDRAM_CS0CFG) & 0xFF;
|
|
if (dramsize >= 0x13)
|
|
dramsize = (1 << (dramsize - 0x13)) << 20;
|
|
else
|
|
dramsize = 0;
|
|
|
|
/* retrieve size of memory connected to SDRAM CS1 */
|
|
dramsize2 = in_be32((void *)MPC5XXX_SDRAM_CS1CFG) & 0xFF;
|
|
if (dramsize2 >= 0x13)
|
|
dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
|
|
else
|
|
dramsize2 = 0;
|
|
|
|
#endif /* CONFIG_SYS_RAMBOOT */
|
|
|
|
/*
|
|
* On MPC5200B we need to set the special configuration delay in the
|
|
* DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
|
|
* Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
|
|
*
|
|
* "The SDelay should be written to a value of 0x00000004. It is
|
|
* required to account for changes caused by normal wafer processing
|
|
* parameters."
|
|
*/
|
|
svr = get_svr();
|
|
pvr = get_pvr();
|
|
if ((SVR_MJREV(svr) >= 2) && (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4))
|
|
out_be32((void *)MPC5XXX_SDRAM_SDELAY, 0x04);
|
|
|
|
return dramsize + dramsize2;
|
|
}
|
|
|
|
static void get_revisions(int *failsavelevel, int *digiboardversion,
|
|
int *fpgaversion)
|
|
{
|
|
struct mpc5xxx_gpt_0_7 *gpt = (struct mpc5xxx_gpt_0_7 *)MPC5XXX_GPT;
|
|
u8 val;
|
|
|
|
/* read digitalboard-version from TMR[2..4] */
|
|
val = 0;
|
|
val |= (gpt->gpt2.sr & (1 << (31 - 23))) ? (1) : 0;
|
|
val |= (gpt->gpt3.sr & (1 << (31 - 23))) ? (1 << 1) : 0;
|
|
val |= (gpt->gpt4.sr & (1 << (31 - 23))) ? (1 << 2) : 0;
|
|
*digiboardversion = val;
|
|
|
|
/*
|
|
* A4M2K only supports digiboardversion. No failsavelevel and
|
|
* fpgaversion here.
|
|
*/
|
|
#if !defined(CONFIG_A4M2K)
|
|
/*
|
|
* Figure out failsavelevel
|
|
* see ticket dsvk#59
|
|
*/
|
|
*failsavelevel = 0; /* 0=failsave, 1=board ok, 2=fpga ok */
|
|
|
|
if (*digiboardversion == 0) {
|
|
*failsavelevel = 1; /* digiboard-version ok */
|
|
|
|
/* read fpga-version from TMR[5..7] */
|
|
val = 0;
|
|
val |= (gpt->gpt5.sr & (1 << (31 - 23))) ? (1) : 0;
|
|
val |= (gpt->gpt6.sr & (1 << (31 - 23))) ? (1 << 1) : 0;
|
|
val |= (gpt->gpt7.sr & (1 << (31 - 23))) ? (1 << 2) : 0;
|
|
*fpgaversion = val;
|
|
|
|
if (*fpgaversion == 1)
|
|
*failsavelevel = 2; /* fpga-version ok */
|
|
}
|
|
#endif
|
|
}
|
|
|
|
/*
|
|
* This function is called from the SPL U-Boot version for
|
|
* early init stuff, that needs to be done for OS (e.g. Linux)
|
|
* booting. Doing it later in the real U-Boot would not work
|
|
* in case that the SPL U-Boot boots Linux directly.
|
|
*/
|
|
void spl_board_init(void)
|
|
{
|
|
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
|
|
struct mpc5xxx_mmap_ctl *mm =
|
|
(struct mpc5xxx_mmap_ctl *)CONFIG_SYS_MBAR;
|
|
|
|
#if defined(CONFIG_A4M2K)
|
|
/* enable CS3 and CS5 (FPGA) */
|
|
setbits_be32(&mm->ipbi_ws_ctrl, (1 << 19) | (1 << 21));
|
|
#else
|
|
int digiboardversion;
|
|
int failsavelevel;
|
|
int fpgaversion;
|
|
u32 val;
|
|
|
|
get_revisions(&failsavelevel, &digiboardversion, &fpgaversion);
|
|
|
|
val = in_be32(&mm->ipbi_ws_ctrl);
|
|
|
|
/* first clear bits 19..21 (CS3...5) */
|
|
val &= ~((1 << 19) | (1 << 20) | (1 << 21));
|
|
if (failsavelevel == 2) {
|
|
/* FPGA ok */
|
|
val |= (1 << 19) | (1 << 21);
|
|
}
|
|
|
|
if (failsavelevel >= 1) {
|
|
/* at least digiboard-version ok */
|
|
val |= (1 << 20);
|
|
}
|
|
|
|
/* And write new value back to register */
|
|
out_be32(&mm->ipbi_ws_ctrl, val);
|
|
|
|
|
|
/* Setup pin multiplexing */
|
|
if (failsavelevel == 2) {
|
|
/* fpga-version ok */
|
|
#if defined(CONFIG_SYS_GPS_PORT_CONFIG_2)
|
|
out_be32(&gpio->port_config, CONFIG_SYS_GPS_PORT_CONFIG_2);
|
|
#endif
|
|
} else if (failsavelevel == 1) {
|
|
/* digiboard-version ok - fpga not */
|
|
#if defined(CONFIG_SYS_GPS_PORT_CONFIG_1)
|
|
out_be32(&gpio->port_config, CONFIG_SYS_GPS_PORT_CONFIG_1);
|
|
#endif
|
|
} else {
|
|
/* full failsave-mode */
|
|
#if defined(CONFIG_SYS_GPS_PORT_CONFIG)
|
|
out_be32(&gpio->port_config, CONFIG_SYS_GPS_PORT_CONFIG);
|
|
#endif
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* Setup gpio_wkup_7 as watchdog AS INPUT to disable it - see
|
|
* ticket #60
|
|
*
|
|
* MPC5XXX_WU_GPIO_DIR direction is already 0 (INPUT)
|
|
* set bit 0(msb) to 1
|
|
*/
|
|
setbits_be32((void *)MPC5XXX_WU_GPIO_ENABLE, CONFIG_WDOG_GPIO_PIN);
|
|
|
|
#if defined(CONFIG_A4M2K)
|
|
/* Setup USB[x] as MPCDiag[0..3] GPIO outputs */
|
|
|
|
/* set USB0,6,7,8 (MPCDiag[0..3]) direction to output */
|
|
gpio->simple_ddr |= 1 << (31 - 15);
|
|
gpio->simple_ddr |= 1 << (31 - 14);
|
|
gpio->simple_ddr |= 1 << (31 - 13);
|
|
gpio->simple_ddr |= 1 << (31 - 12);
|
|
|
|
/* enable USB0,6,7,8 (MPCDiag[0..3]) as GPIO */
|
|
gpio->simple_gpioe |= 1 << (31 - 15);
|
|
gpio->simple_gpioe |= 1 << (31 - 14);
|
|
gpio->simple_gpioe |= 1 << (31 - 13);
|
|
gpio->simple_gpioe |= 1 << (31 - 12);
|
|
|
|
/* Setup PSC2[0..2] as STSLED[0..2] GPIO outputs */
|
|
|
|
/* set PSC2[0..2] (STSLED[0..2]) direction to output */
|
|
gpio->simple_ddr |= 1 << (31 - 27);
|
|
gpio->simple_ddr |= 1 << (31 - 26);
|
|
gpio->simple_ddr |= 1 << (31 - 25);
|
|
|
|
/* enable PSC2[0..2] (STSLED[0..2]) as GPIO */
|
|
gpio->simple_gpioe |= 1 << (31 - 27);
|
|
gpio->simple_gpioe |= 1 << (31 - 26);
|
|
gpio->simple_gpioe |= 1 << (31 - 25);
|
|
|
|
/* Setup PSC6[2] as MRST2 self reset GPIO output */
|
|
|
|
/* set PSC6[2]/IRDA_TX (MRST2) direction to output */
|
|
gpio->simple_ddr |= 1 << (31 - 3);
|
|
|
|
/* set PSC6[2]/IRDA_TX (MRST2) output as open drain */
|
|
gpio->simple_ode |= 1 << (31 - 3);
|
|
|
|
/* set PSC6[2]/IRDA_TX (MRST2) output as default high */
|
|
gpio->simple_dvo |= 1 << (31 - 3);
|
|
|
|
/* enable PSC6[2]/IRDA_TX (MRST2) as GPIO */
|
|
gpio->simple_gpioe |= 1 << (31 - 3);
|
|
|
|
/* Setup PSC6[3] as HARNSSCD harness code GPIO input */
|
|
|
|
/* set PSC6[3]/IR_USB_CLK (HARNSSCD) direction to input */
|
|
gpio->simple_ddr |= 0 << (31 - 2);
|
|
|
|
/* enable PSC6[3]/IR_USB_CLK (HARNSSCD) as GPIO */
|
|
gpio->simple_gpioe |= 1 << (31 - 2);
|
|
#else
|
|
/* setup GPIOs for status-leds if needed - see ticket #57 */
|
|
if (failsavelevel > 0) {
|
|
/* digiboard-version is OK */
|
|
/* LED is LOW ACTIVE - so deactivate by set output to 1 */
|
|
gpio->simple_dvo |= 1 << (31 - 12);
|
|
gpio->simple_dvo |= 1 << (31 - 13);
|
|
/* set GPIO direction to output */
|
|
gpio->simple_ddr |= 1 << (31 - 12);
|
|
gpio->simple_ddr |= 1 << (31 - 13);
|
|
/* open drain config is set to "normal output" at reset */
|
|
/* gpio->simple_ode &=~ ( 1 << (31-12) ); */
|
|
/* gpio->simple_ode &=~ ( 1 << (31-13) ); */
|
|
/* enable as GPIO */
|
|
gpio->simple_gpioe |= 1 << (31 - 12);
|
|
gpio->simple_gpioe |= 1 << (31 - 13);
|
|
}
|
|
|
|
/* setup fpga irq - see ticket #65 */
|
|
if (failsavelevel > 1) {
|
|
/*
|
|
* The main irq initialisation is done in interrupts.c
|
|
* mpc5xxx_init_irq
|
|
*/
|
|
struct mpc5xxx_intr *intr =
|
|
(struct mpc5xxx_intr *)(MPC5XXX_ICTL);
|
|
|
|
setbits_be32(&intr->ctrl, 0x08C01801);
|
|
|
|
/*
|
|
* The MBAR+0x0524 Bit 21:23 CSe are ignored here due to the
|
|
* already cleared (intr_ctrl) MBAR+0x0510 ECLR[0] bit above
|
|
*/
|
|
}
|
|
#endif
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
int digiboardversion;
|
|
int failsavelevel;
|
|
int fpgaversion;
|
|
|
|
get_revisions(&failsavelevel, &digiboardversion, &fpgaversion);
|
|
|
|
#ifdef CONFIG_A4M2K
|
|
puts("Board: A4M2K\n");
|
|
printf(" digiboard IO version %u\n", digiboardversion);
|
|
#else
|
|
puts("Board: A3M071\n");
|
|
printf("Rev: failsave level %u\n", failsavelevel);
|
|
printf(" digiboard IO version %u\n", digiboardversion);
|
|
if (failsavelevel > 0) /* only if fpga-version red */
|
|
printf(" fpga IO version %u\n", fpgaversion);
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* miscellaneous platform dependent initialisations */
|
|
int misc_init_r(void)
|
|
{
|
|
/* adjust flash start and offset to detected values */
|
|
gd->bd->bi_flashstart = flash_info[0].start[0];
|
|
gd->bd->bi_flashoffset = 0;
|
|
|
|
/* adjust mapping */
|
|
out_be32((void *)MPC5XXX_BOOTCS_START,
|
|
START_REG(gd->bd->bi_flashstart));
|
|
out_be32((void *)MPC5XXX_CS0_START, START_REG(gd->bd->bi_flashstart));
|
|
out_be32((void *)MPC5XXX_BOOTCS_STOP,
|
|
STOP_REG(gd->bd->bi_flashstart, gd->bd->bi_flashsize));
|
|
out_be32((void *)MPC5XXX_CS0_STOP,
|
|
STOP_REG(gd->bd->bi_flashstart, gd->bd->bi_flashsize));
|
|
|
|
return 0;
|
|
}
|
|
|
|
#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
|
|
int ft_board_setup(void *blob, bd_t *bd)
|
|
{
|
|
ft_cpu_setup(blob, bd);
|
|
|
|
return 0;
|
|
}
|
|
#endif /* defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) */
|
|
|
|
#ifdef CONFIG_SPL_OS_BOOT
|
|
/*
|
|
* A3M071 specific implementation of spl_start_uboot()
|
|
*
|
|
* RETURN
|
|
* 0 if booting into OS is selected (default)
|
|
* 1 if booting into U-Boot is selected
|
|
*/
|
|
int spl_start_uboot(void)
|
|
{
|
|
char s[8];
|
|
|
|
env_init();
|
|
getenv_f("boot_os", s, sizeof(s));
|
|
if ((s != NULL) && (*s == '1' || *s == 'y' || *s == 'Y' ||
|
|
*s == 't' || *s == 'T'))
|
|
return 0;
|
|
|
|
return 1;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_HW_WATCHDOG)
|
|
static int watchdog_toggle;
|
|
|
|
void hw_watchdog_reset(void)
|
|
{
|
|
int val;
|
|
|
|
/*
|
|
* Check if watchdog is enabled via user command
|
|
*/
|
|
if ((gd->flags & GD_FLG_RELOC) && watchdog_toggle) {
|
|
/* Set direction to output */
|
|
setbits_be32((void *)MPC5XXX_WU_GPIO_DIR, CONFIG_WDOG_GPIO_PIN);
|
|
|
|
/*
|
|
* Toggle watchdog output
|
|
*/
|
|
val = (in_be32((void *)MPC5XXX_WU_GPIO_DATA_O) &
|
|
CONFIG_WDOG_GPIO_PIN);
|
|
if (val) {
|
|
clrbits_be32((void *)MPC5XXX_WU_GPIO_DATA_O,
|
|
CONFIG_WDOG_GPIO_PIN);
|
|
} else {
|
|
setbits_be32((void *)MPC5XXX_WU_GPIO_DATA_O,
|
|
CONFIG_WDOG_GPIO_PIN);
|
|
}
|
|
}
|
|
}
|
|
|
|
int do_wdog_toggle(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
|
|
{
|
|
if (argc != 2)
|
|
goto usage;
|
|
|
|
if (strncmp(argv[1], "on", 2) == 0)
|
|
watchdog_toggle = 1;
|
|
else if (strncmp(argv[1], "off", 3) == 0)
|
|
watchdog_toggle = 0;
|
|
else
|
|
goto usage;
|
|
|
|
return 0;
|
|
usage:
|
|
printf("Usage: wdogtoggle %s\n", cmdtp->usage);
|
|
return 1;
|
|
}
|
|
|
|
U_BOOT_CMD(
|
|
wdogtoggle, CONFIG_SYS_MAXARGS, 2, do_wdog_toggle,
|
|
"toggle GPIO pin to service watchdog",
|
|
"[on/off] - Switch watchdog toggling via GPIO pin on/off"
|
|
);
|
|
#endif
|
|
|