upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
2644 lines
75 KiB
2644 lines
75 KiB
/*
|
|
* Copyright (C) Marvell International Ltd. and its affiliates
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <spl.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
|
|
#include "ddr3_init.h"
|
|
|
|
#define GET_MAX_VALUE(x, y) \
|
|
((x) > (y)) ? (x) : (y)
|
|
#define CEIL_DIVIDE(x, y) \
|
|
((x - (x / y) * y) == 0) ? ((x / y) - 1) : (x / y)
|
|
|
|
#define TIME_2_CLOCK_CYCLES CEIL_DIVIDE
|
|
|
|
#define GET_CS_FROM_MASK(mask) (cs_mask2_num[mask])
|
|
#define CS_CBE_VALUE(cs_num) (cs_cbe_reg[cs_num])
|
|
|
|
u32 window_mem_addr = 0;
|
|
u32 phy_reg0_val = 0;
|
|
u32 phy_reg1_val = 8;
|
|
u32 phy_reg2_val = 0;
|
|
u32 phy_reg3_val = 0xa;
|
|
enum hws_ddr_freq init_freq = DDR_FREQ_667;
|
|
enum hws_ddr_freq low_freq = DDR_FREQ_LOW_FREQ;
|
|
enum hws_ddr_freq medium_freq;
|
|
u32 debug_dunit = 0;
|
|
u32 odt_additional = 1;
|
|
u32 *dq_map_table = NULL;
|
|
u32 odt_config = 1;
|
|
|
|
#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ALLEYCAT3) || \
|
|
defined(CONFIG_ARMADA_39X)
|
|
u32 is_pll_before_init = 0, is_adll_calib_before_init = 0, is_dfs_in_init = 0;
|
|
u32 dfs_low_freq = 130;
|
|
#else
|
|
u32 is_pll_before_init = 0, is_adll_calib_before_init = 1, is_dfs_in_init = 0;
|
|
u32 dfs_low_freq = 100;
|
|
#endif
|
|
u32 g_rtt_nom_c_s0, g_rtt_nom_c_s1;
|
|
u8 calibration_update_control; /* 2 external only, 1 is internal only */
|
|
|
|
enum hws_result training_result[MAX_STAGE_LIMIT][MAX_INTERFACE_NUM];
|
|
enum auto_tune_stage training_stage = INIT_CONTROLLER;
|
|
u32 finger_test = 0, p_finger_start = 11, p_finger_end = 64,
|
|
n_finger_start = 11, n_finger_end = 64,
|
|
p_finger_step = 3, n_finger_step = 3;
|
|
u32 clamp_tbl[] = { 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3 };
|
|
|
|
/* Initiate to 0xff, this variable is define by user in debug mode */
|
|
u32 mode2_t = 0xff;
|
|
u32 xsb_validate_type = 0;
|
|
u32 xsb_validation_base_address = 0xf000;
|
|
u32 first_active_if = 0;
|
|
u32 dfs_low_phy1 = 0x1f;
|
|
u32 multicast_id = 0;
|
|
int use_broadcast = 0;
|
|
struct hws_tip_freq_config_info *freq_info_table = NULL;
|
|
u8 is_cbe_required = 0;
|
|
u32 debug_mode = 0;
|
|
u32 delay_enable = 0;
|
|
int rl_mid_freq_wa = 0;
|
|
|
|
u32 effective_cs = 0;
|
|
|
|
u32 mask_tune_func = (SET_MEDIUM_FREQ_MASK_BIT |
|
|
WRITE_LEVELING_MASK_BIT |
|
|
LOAD_PATTERN_2_MASK_BIT |
|
|
READ_LEVELING_MASK_BIT |
|
|
SET_TARGET_FREQ_MASK_BIT | WRITE_LEVELING_TF_MASK_BIT |
|
|
READ_LEVELING_TF_MASK_BIT |
|
|
CENTRALIZATION_RX_MASK_BIT | CENTRALIZATION_TX_MASK_BIT);
|
|
|
|
void ddr3_print_version(void)
|
|
{
|
|
printf(DDR3_TIP_VERSION_STRING);
|
|
}
|
|
|
|
static int ddr3_tip_ddr3_training_main_flow(u32 dev_num);
|
|
static int ddr3_tip_write_odt(u32 dev_num, enum hws_access_type access_type,
|
|
u32 if_id, u32 cl_value, u32 cwl_value);
|
|
static int ddr3_tip_ddr3_auto_tune(u32 dev_num);
|
|
static int is_bus_access_done(u32 dev_num, u32 if_id,
|
|
u32 dunit_reg_adrr, u32 bit);
|
|
#ifdef ODT_TEST_SUPPORT
|
|
static int odt_test(u32 dev_num, enum hws_algo_type algo_type);
|
|
#endif
|
|
|
|
int adll_calibration(u32 dev_num, enum hws_access_type access_type,
|
|
u32 if_id, enum hws_ddr_freq frequency);
|
|
static int ddr3_tip_set_timing(u32 dev_num, enum hws_access_type access_type,
|
|
u32 if_id, enum hws_ddr_freq frequency);
|
|
|
|
static struct page_element page_param[] = {
|
|
/*
|
|
* 8bits 16 bits
|
|
* page-size(K) page-size(K) mask
|
|
*/
|
|
{ 1, 2, 2},
|
|
/* 512M */
|
|
{ 1, 2, 3},
|
|
/* 1G */
|
|
{ 1, 2, 0},
|
|
/* 2G */
|
|
{ 1, 2, 4},
|
|
/* 4G */
|
|
{ 2, 2, 5}
|
|
/* 8G */
|
|
};
|
|
|
|
static u8 mem_size_config[MEM_SIZE_LAST] = {
|
|
0x2, /* 512Mbit */
|
|
0x3, /* 1Gbit */
|
|
0x0, /* 2Gbit */
|
|
0x4, /* 4Gbit */
|
|
0x5 /* 8Gbit */
|
|
};
|
|
|
|
static u8 cs_mask2_num[] = { 0, 0, 1, 1, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3 };
|
|
|
|
static struct reg_data odpg_default_value[] = {
|
|
{0x1034, 0x38000, MASK_ALL_BITS},
|
|
{0x1038, 0x0, MASK_ALL_BITS},
|
|
{0x10b0, 0x0, MASK_ALL_BITS},
|
|
{0x10b8, 0x0, MASK_ALL_BITS},
|
|
{0x10c0, 0x0, MASK_ALL_BITS},
|
|
{0x10f0, 0x0, MASK_ALL_BITS},
|
|
{0x10f4, 0x0, MASK_ALL_BITS},
|
|
{0x10f8, 0xff, MASK_ALL_BITS},
|
|
{0x10fc, 0xffff, MASK_ALL_BITS},
|
|
{0x1130, 0x0, MASK_ALL_BITS},
|
|
{0x1830, 0x2000000, MASK_ALL_BITS},
|
|
{0x14d0, 0x0, MASK_ALL_BITS},
|
|
{0x14d4, 0x0, MASK_ALL_BITS},
|
|
{0x14d8, 0x0, MASK_ALL_BITS},
|
|
{0x14dc, 0x0, MASK_ALL_BITS},
|
|
{0x1454, 0x0, MASK_ALL_BITS},
|
|
{0x1594, 0x0, MASK_ALL_BITS},
|
|
{0x1598, 0x0, MASK_ALL_BITS},
|
|
{0x159c, 0x0, MASK_ALL_BITS},
|
|
{0x15a0, 0x0, MASK_ALL_BITS},
|
|
{0x15a4, 0x0, MASK_ALL_BITS},
|
|
{0x15a8, 0x0, MASK_ALL_BITS},
|
|
{0x15ac, 0x0, MASK_ALL_BITS},
|
|
{0x1604, 0x0, MASK_ALL_BITS},
|
|
{0x1608, 0x0, MASK_ALL_BITS},
|
|
{0x160c, 0x0, MASK_ALL_BITS},
|
|
{0x1610, 0x0, MASK_ALL_BITS},
|
|
{0x1614, 0x0, MASK_ALL_BITS},
|
|
{0x1618, 0x0, MASK_ALL_BITS},
|
|
{0x1624, 0x0, MASK_ALL_BITS},
|
|
{0x1690, 0x0, MASK_ALL_BITS},
|
|
{0x1694, 0x0, MASK_ALL_BITS},
|
|
{0x1698, 0x0, MASK_ALL_BITS},
|
|
{0x169c, 0x0, MASK_ALL_BITS},
|
|
{0x14b8, 0x6f67, MASK_ALL_BITS},
|
|
{0x1630, 0x0, MASK_ALL_BITS},
|
|
{0x1634, 0x0, MASK_ALL_BITS},
|
|
{0x1638, 0x0, MASK_ALL_BITS},
|
|
{0x163c, 0x0, MASK_ALL_BITS},
|
|
{0x16b0, 0x0, MASK_ALL_BITS},
|
|
{0x16b4, 0x0, MASK_ALL_BITS},
|
|
{0x16b8, 0x0, MASK_ALL_BITS},
|
|
{0x16bc, 0x0, MASK_ALL_BITS},
|
|
{0x16c0, 0x0, MASK_ALL_BITS},
|
|
{0x16c4, 0x0, MASK_ALL_BITS},
|
|
{0x16c8, 0x0, MASK_ALL_BITS},
|
|
{0x16cc, 0x1, MASK_ALL_BITS},
|
|
{0x16f0, 0x1, MASK_ALL_BITS},
|
|
{0x16f4, 0x0, MASK_ALL_BITS},
|
|
{0x16f8, 0x0, MASK_ALL_BITS},
|
|
{0x16fc, 0x0, MASK_ALL_BITS}
|
|
};
|
|
|
|
static int ddr3_tip_bus_access(u32 dev_num, enum hws_access_type interface_access,
|
|
u32 if_id, enum hws_access_type phy_access,
|
|
u32 phy_id, enum hws_ddr_phy phy_type, u32 reg_addr,
|
|
u32 data_value, enum hws_operation oper_type);
|
|
static int ddr3_tip_pad_inv(u32 dev_num, u32 if_id);
|
|
static int ddr3_tip_rank_control(u32 dev_num, u32 if_id);
|
|
|
|
/*
|
|
* Update global training parameters by data from user
|
|
*/
|
|
int ddr3_tip_tune_training_params(u32 dev_num,
|
|
struct tune_train_params *params)
|
|
{
|
|
if (params->ck_delay != -1)
|
|
ck_delay = params->ck_delay;
|
|
if (params->ck_delay_16 != -1)
|
|
ck_delay_16 = params->ck_delay_16;
|
|
if (params->phy_reg3_val != -1)
|
|
phy_reg3_val = params->phy_reg3_val;
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Configure CS
|
|
*/
|
|
int ddr3_tip_configure_cs(u32 dev_num, u32 if_id, u32 cs_num, u32 enable)
|
|
{
|
|
u32 data, addr_hi, data_high;
|
|
u32 mem_index;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
if (enable == 1) {
|
|
data = (tm->interface_params[if_id].bus_width ==
|
|
BUS_WIDTH_8) ? 0 : 1;
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
SDRAM_ACCESS_CONTROL_REG, (data << (cs_num * 4)),
|
|
0x3 << (cs_num * 4)));
|
|
mem_index = tm->interface_params[if_id].memory_size;
|
|
|
|
addr_hi = mem_size_config[mem_index] & 0x3;
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
SDRAM_ACCESS_CONTROL_REG,
|
|
(addr_hi << (2 + cs_num * 4)),
|
|
0x3 << (2 + cs_num * 4)));
|
|
|
|
data_high = (mem_size_config[mem_index] & 0x4) >> 2;
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
SDRAM_ACCESS_CONTROL_REG,
|
|
data_high << (20 + cs_num), 1 << (20 + cs_num)));
|
|
|
|
/* Enable Address Select Mode */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
SDRAM_ACCESS_CONTROL_REG, 1 << (16 + cs_num),
|
|
1 << (16 + cs_num)));
|
|
}
|
|
switch (cs_num) {
|
|
case 0:
|
|
case 1:
|
|
case 2:
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
DDR_CONTROL_LOW_REG, (enable << (cs_num + 11)),
|
|
1 << (cs_num + 11)));
|
|
break;
|
|
case 3:
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
DDR_CONTROL_LOW_REG, (enable << 15), 1 << 15));
|
|
break;
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Calculate number of CS
|
|
*/
|
|
static int calc_cs_num(u32 dev_num, u32 if_id, u32 *cs_num)
|
|
{
|
|
u32 cs;
|
|
u32 bus_cnt;
|
|
u32 cs_count;
|
|
u32 cs_bitmask;
|
|
u32 curr_cs_num = 0;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
for (bus_cnt = 0; bus_cnt < GET_TOPOLOGY_NUM_OF_BUSES(); bus_cnt++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_cnt);
|
|
cs_count = 0;
|
|
cs_bitmask = tm->interface_params[if_id].
|
|
as_bus_params[bus_cnt].cs_bitmask;
|
|
for (cs = 0; cs < MAX_CS_NUM; cs++) {
|
|
if ((cs_bitmask >> cs) & 1)
|
|
cs_count++;
|
|
}
|
|
|
|
if (curr_cs_num == 0) {
|
|
curr_cs_num = cs_count;
|
|
} else if (cs_count != curr_cs_num) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("CS number is different per bus (IF %d BUS %d cs_num %d curr_cs_num %d)\n",
|
|
if_id, bus_cnt, cs_count,
|
|
curr_cs_num));
|
|
return MV_NOT_SUPPORTED;
|
|
}
|
|
}
|
|
*cs_num = curr_cs_num;
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Init Controller Flow
|
|
*/
|
|
int hws_ddr3_tip_init_controller(u32 dev_num, struct init_cntr_param *init_cntr_prm)
|
|
{
|
|
u32 if_id;
|
|
u32 cs_num;
|
|
u32 t_refi = 0, t_hclk = 0, t_ckclk = 0, t_faw = 0, t_pd = 0,
|
|
t_wr = 0, t2t = 0, txpdll = 0;
|
|
u32 data_value = 0, bus_width = 0, page_size = 0, cs_cnt = 0,
|
|
mem_mask = 0, bus_index = 0;
|
|
enum hws_speed_bin speed_bin_index = SPEED_BIN_DDR_2133N;
|
|
enum hws_mem_size memory_size = MEM_2G;
|
|
enum hws_ddr_freq freq = init_freq;
|
|
u32 cs_mask = 0;
|
|
u32 cl_value = 0, cwl_val = 0;
|
|
u32 refresh_interval_cnt = 0, bus_cnt = 0, adll_tap = 0;
|
|
enum hws_access_type access_type = ACCESS_TYPE_UNICAST;
|
|
u32 data_read[MAX_INTERFACE_NUM];
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE,
|
|
("Init_controller, do_mrs_phy=%d, is_ctrl64_bit=%d\n",
|
|
init_cntr_prm->do_mrs_phy,
|
|
init_cntr_prm->is_ctrl64_bit));
|
|
|
|
if (init_cntr_prm->init_phy == 1) {
|
|
CHECK_STATUS(ddr3_tip_configure_phy(dev_num));
|
|
}
|
|
|
|
if (generic_init_controller == 1) {
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE,
|
|
("active IF %d\n", if_id));
|
|
mem_mask = 0;
|
|
for (bus_index = 0;
|
|
bus_index < GET_TOPOLOGY_NUM_OF_BUSES();
|
|
bus_index++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_index);
|
|
mem_mask |=
|
|
tm->interface_params[if_id].
|
|
as_bus_params[bus_index].mirror_enable_bitmask;
|
|
}
|
|
|
|
if (mem_mask != 0) {
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_MULTICAST,
|
|
if_id, CS_ENABLE_REG, 0,
|
|
0x8));
|
|
}
|
|
|
|
memory_size =
|
|
tm->interface_params[if_id].
|
|
memory_size;
|
|
speed_bin_index =
|
|
tm->interface_params[if_id].
|
|
speed_bin_index;
|
|
freq = init_freq;
|
|
t_refi =
|
|
(tm->interface_params[if_id].
|
|
interface_temp ==
|
|
HWS_TEMP_HIGH) ? TREFI_HIGH : TREFI_LOW;
|
|
t_refi *= 1000; /* psec */
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE,
|
|
("memy_size %d speed_bin_ind %d freq %d t_refi %d\n",
|
|
memory_size, speed_bin_index, freq,
|
|
t_refi));
|
|
/* HCLK & CK CLK in 2:1[ps] */
|
|
/* t_ckclk is external clock */
|
|
t_ckclk = (MEGA / freq_val[freq]);
|
|
/* t_hclk is internal clock */
|
|
t_hclk = 2 * t_ckclk;
|
|
refresh_interval_cnt = t_refi / t_hclk; /* no units */
|
|
bus_width =
|
|
(DDR3_IS_16BIT_DRAM_MODE(tm->bus_act_mask)
|
|
== 1) ? (16) : (32);
|
|
|
|
if (init_cntr_prm->is_ctrl64_bit)
|
|
bus_width = 64;
|
|
|
|
data_value =
|
|
(refresh_interval_cnt | 0x4000 |
|
|
((bus_width ==
|
|
32) ? 0x8000 : 0) | 0x1000000) & ~(1 << 26);
|
|
|
|
/* Interface Bus Width */
|
|
/* SRMode */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
SDRAM_CONFIGURATION_REG, data_value,
|
|
0x100ffff));
|
|
|
|
/* Interleave first command pre-charge enable (TBD) */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
SDRAM_OPEN_PAGE_CONTROL_REG, (1 << 10),
|
|
(1 << 10)));
|
|
|
|
/* PHY configuration */
|
|
/*
|
|
* Postamble Length = 1.5cc, Addresscntl to clk skew
|
|
* \BD, Preamble length normal, parralal ADLL enable
|
|
*/
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DRAM_PHY_CONFIGURATION, 0x28, 0x3e));
|
|
if (init_cntr_prm->is_ctrl64_bit) {
|
|
/* positive edge */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DRAM_PHY_CONFIGURATION, 0x0,
|
|
0xff80));
|
|
}
|
|
|
|
/* calibration block disable */
|
|
/* Xbar Read buffer select (for Internal access) */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
CALIB_MACHINE_CTRL_REG, 0x1200c,
|
|
0x7dffe01c));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
CALIB_MACHINE_CTRL_REG,
|
|
calibration_update_control << 3, 0x3 << 3));
|
|
|
|
/* Pad calibration control - enable */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
CALIB_MACHINE_CTRL_REG, 0x1, 0x1));
|
|
|
|
cs_mask = 0;
|
|
data_value = 0x7;
|
|
/*
|
|
* Address ctrl \96 Part of the Generic code
|
|
* The next configuration is done:
|
|
* 1) Memory Size
|
|
* 2) Bus_width
|
|
* 3) CS#
|
|
* 4) Page Number
|
|
* 5) t_faw
|
|
* Per Dunit get from the Map_topology the parameters:
|
|
* Bus_width
|
|
* t_faw is per Dunit not per CS
|
|
*/
|
|
page_size =
|
|
(tm->interface_params[if_id].
|
|
bus_width ==
|
|
BUS_WIDTH_8) ? page_param[memory_size].
|
|
page_size_8bit : page_param[memory_size].
|
|
page_size_16bit;
|
|
|
|
t_faw =
|
|
(page_size == 1) ? speed_bin_table(speed_bin_index,
|
|
SPEED_BIN_TFAW1K)
|
|
: speed_bin_table(speed_bin_index,
|
|
SPEED_BIN_TFAW2K);
|
|
|
|
data_value = TIME_2_CLOCK_CYCLES(t_faw, t_ckclk);
|
|
data_value = data_value << 24;
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
SDRAM_ACCESS_CONTROL_REG, data_value,
|
|
0x7f000000));
|
|
|
|
data_value =
|
|
(tm->interface_params[if_id].
|
|
bus_width == BUS_WIDTH_8) ? 0 : 1;
|
|
|
|
/* create merge cs mask for all cs available in dunit */
|
|
for (bus_cnt = 0;
|
|
bus_cnt < GET_TOPOLOGY_NUM_OF_BUSES();
|
|
bus_cnt++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_cnt);
|
|
cs_mask |=
|
|
tm->interface_params[if_id].
|
|
as_bus_params[bus_cnt].cs_bitmask;
|
|
}
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE,
|
|
("Init_controller IF %d cs_mask %d\n",
|
|
if_id, cs_mask));
|
|
/*
|
|
* Configure the next upon the Map Topology \96 If the
|
|
* Dunit is CS0 Configure CS0 if it is multi CS
|
|
* configure them both: The Bust_width it\92s the
|
|
* Memory Bus width \96 x8 or x16
|
|
*/
|
|
for (cs_cnt = 0; cs_cnt < NUM_OF_CS; cs_cnt++) {
|
|
ddr3_tip_configure_cs(dev_num, if_id, cs_cnt,
|
|
((cs_mask & (1 << cs_cnt)) ? 1
|
|
: 0));
|
|
}
|
|
|
|
if (init_cntr_prm->do_mrs_phy) {
|
|
/*
|
|
* MR0 \96 Part of the Generic code
|
|
* The next configuration is done:
|
|
* 1) Burst Length
|
|
* 2) CAS Latency
|
|
* get for each dunit what is it Speed_bin &
|
|
* Target Frequency. From those both parameters
|
|
* get the appropriate Cas_l from the CL table
|
|
*/
|
|
cl_value =
|
|
tm->interface_params[if_id].
|
|
cas_l;
|
|
cwl_val =
|
|
tm->interface_params[if_id].
|
|
cas_wl;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE,
|
|
("cl_value 0x%x cwl_val 0x%x\n",
|
|
cl_value, cwl_val));
|
|
|
|
data_value =
|
|
((cl_mask_table[cl_value] & 0x1) << 2) |
|
|
((cl_mask_table[cl_value] & 0xe) << 3);
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
MR0_REG, data_value,
|
|
(0x7 << 4) | (1 << 2)));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
MR0_REG, twr_mask_table[t_wr + 1],
|
|
0xe00));
|
|
|
|
/*
|
|
* MR1: Set RTT and DIC Design GL values
|
|
* configured by user
|
|
*/
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_MULTICAST,
|
|
PARAM_NOT_CARE, MR1_REG,
|
|
g_dic | g_rtt_nom, 0x266));
|
|
|
|
/* MR2 - Part of the Generic code */
|
|
/*
|
|
* The next configuration is done:
|
|
* 1) SRT
|
|
* 2) CAS Write Latency
|
|
*/
|
|
data_value = (cwl_mask_table[cwl_val] << 3);
|
|
data_value |=
|
|
((tm->interface_params[if_id].
|
|
interface_temp ==
|
|
HWS_TEMP_HIGH) ? (1 << 7) : 0);
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
MR2_REG, data_value,
|
|
(0x7 << 3) | (0x1 << 7) | (0x3 <<
|
|
9)));
|
|
}
|
|
|
|
ddr3_tip_write_odt(dev_num, access_type, if_id,
|
|
cl_value, cwl_val);
|
|
ddr3_tip_set_timing(dev_num, access_type, if_id, freq);
|
|
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DUNIT_CONTROL_HIGH_REG, 0x177,
|
|
0x1000177));
|
|
|
|
if (init_cntr_prm->is_ctrl64_bit) {
|
|
/* disable 0.25 cc delay */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DUNIT_CONTROL_HIGH_REG, 0x0,
|
|
0x800));
|
|
}
|
|
|
|
/* reset bit 7 */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DUNIT_CONTROL_HIGH_REG,
|
|
(init_cntr_prm->msys_init << 7), (1 << 7)));
|
|
|
|
if (mode2_t != 0xff) {
|
|
t2t = mode2_t;
|
|
} else {
|
|
/* calculate number of CS (per interface) */
|
|
CHECK_STATUS(calc_cs_num
|
|
(dev_num, if_id, &cs_num));
|
|
t2t = (cs_num == 1) ? 0 : 1;
|
|
}
|
|
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DDR_CONTROL_LOW_REG, t2t << 3,
|
|
0x3 << 3));
|
|
/* move the block to ddr3_tip_set_timing - start */
|
|
t_pd = GET_MAX_VALUE(t_ckclk * 3,
|
|
speed_bin_table(speed_bin_index,
|
|
SPEED_BIN_TPD));
|
|
t_pd = TIME_2_CLOCK_CYCLES(t_pd, t_ckclk);
|
|
txpdll = GET_MAX_VALUE(t_ckclk * 10, 24);
|
|
txpdll = CEIL_DIVIDE((txpdll - 1), t_ckclk);
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DDR_TIMING_REG, txpdll << 4,
|
|
0x1f << 4));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DDR_TIMING_REG, 0x28 << 9, 0x3f << 9));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DDR_TIMING_REG, 0xa << 21, 0xff << 21));
|
|
|
|
/* move the block to ddr3_tip_set_timing - end */
|
|
/* AUTO_ZQC_TIMING */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
TIMING_REG, (AUTO_ZQC_TIMING | (2 << 20)),
|
|
0x3fffff));
|
|
CHECK_STATUS(ddr3_tip_if_read
|
|
(dev_num, access_type, if_id,
|
|
DRAM_PHY_CONFIGURATION, data_read, 0x30));
|
|
data_value =
|
|
(data_read[if_id] == 0) ? (1 << 11) : 0;
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DUNIT_CONTROL_HIGH_REG, data_value,
|
|
(1 << 11)));
|
|
|
|
/* Set Active control for ODT write transactions */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_MULTICAST,
|
|
PARAM_NOT_CARE, 0x1494, g_odt_config,
|
|
MASK_ALL_BITS));
|
|
}
|
|
} else {
|
|
#ifdef STATIC_ALGO_SUPPORT
|
|
CHECK_STATUS(ddr3_tip_static_init_controller(dev_num));
|
|
#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)
|
|
CHECK_STATUS(ddr3_tip_static_phy_init_controller(dev_num));
|
|
#endif
|
|
#endif /* STATIC_ALGO_SUPPORT */
|
|
}
|
|
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
CHECK_STATUS(ddr3_tip_rank_control(dev_num, if_id));
|
|
|
|
if (init_cntr_prm->do_mrs_phy) {
|
|
CHECK_STATUS(ddr3_tip_pad_inv(dev_num, if_id));
|
|
}
|
|
|
|
/* Pad calibration control - disable */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
CALIB_MACHINE_CTRL_REG, 0x0, 0x1));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
CALIB_MACHINE_CTRL_REG,
|
|
calibration_update_control << 3, 0x3 << 3));
|
|
}
|
|
|
|
CHECK_STATUS(ddr3_tip_enable_init_sequence(dev_num));
|
|
|
|
if (delay_enable != 0) {
|
|
adll_tap = MEGA / (freq_val[freq] * 64);
|
|
ddr3_tip_cmd_addr_init_delay(dev_num, adll_tap);
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Load Topology map
|
|
*/
|
|
int hws_ddr3_tip_load_topology_map(u32 dev_num, struct hws_topology_map *tm)
|
|
{
|
|
enum hws_speed_bin speed_bin_index;
|
|
enum hws_ddr_freq freq = DDR_FREQ_LIMIT;
|
|
u32 if_id;
|
|
|
|
freq_val[DDR_FREQ_LOW_FREQ] = dfs_low_freq;
|
|
tm = ddr3_get_topology_map();
|
|
CHECK_STATUS(ddr3_tip_get_first_active_if
|
|
((u8)dev_num, tm->if_act_mask,
|
|
&first_active_if));
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE,
|
|
("board IF_Mask=0x%x num_of_bus_per_interface=0x%x\n",
|
|
tm->if_act_mask,
|
|
tm->num_of_bus_per_interface));
|
|
|
|
/*
|
|
* if CL, CWL values are missing in topology map, then fill them
|
|
* according to speedbin tables
|
|
*/
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
speed_bin_index =
|
|
tm->interface_params[if_id].speed_bin_index;
|
|
/* TBD memory frequency of interface 0 only is used ! */
|
|
freq = tm->interface_params[first_active_if].memory_freq;
|
|
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE,
|
|
("speed_bin_index =%d freq=%d cl=%d cwl=%d\n",
|
|
speed_bin_index, freq_val[freq],
|
|
tm->interface_params[if_id].
|
|
cas_l,
|
|
tm->interface_params[if_id].
|
|
cas_wl));
|
|
|
|
if (tm->interface_params[if_id].cas_l == 0) {
|
|
tm->interface_params[if_id].cas_l =
|
|
cas_latency_table[speed_bin_index].cl_val[freq];
|
|
}
|
|
|
|
if (tm->interface_params[if_id].cas_wl == 0) {
|
|
tm->interface_params[if_id].cas_wl =
|
|
cas_write_latency_table[speed_bin_index].cl_val[freq];
|
|
}
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* RANK Control Flow
|
|
*/
|
|
static int ddr3_tip_rank_control(u32 dev_num, u32 if_id)
|
|
{
|
|
u32 data_value = 0, bus_cnt;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
for (bus_cnt = 1; bus_cnt < GET_TOPOLOGY_NUM_OF_BUSES(); bus_cnt++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_cnt);
|
|
if ((tm->interface_params[if_id].
|
|
as_bus_params[0].cs_bitmask !=
|
|
tm->interface_params[if_id].
|
|
as_bus_params[bus_cnt].cs_bitmask) ||
|
|
(tm->interface_params[if_id].
|
|
as_bus_params[0].mirror_enable_bitmask !=
|
|
tm->interface_params[if_id].
|
|
as_bus_params[bus_cnt].mirror_enable_bitmask))
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("WARNING:Wrong configuration for pup #%d CS mask and CS mirroring for all pups should be the same\n",
|
|
bus_cnt));
|
|
}
|
|
|
|
data_value |= tm->interface_params[if_id].
|
|
as_bus_params[0].cs_bitmask;
|
|
data_value |= tm->interface_params[if_id].
|
|
as_bus_params[0].mirror_enable_bitmask << 4;
|
|
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id, RANK_CTRL_REG,
|
|
data_value, 0xff));
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* PAD Inverse Flow
|
|
*/
|
|
static int ddr3_tip_pad_inv(u32 dev_num, u32 if_id)
|
|
{
|
|
u32 bus_cnt, data_value, ck_swap_pup_ctrl;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
for (bus_cnt = 0; bus_cnt < GET_TOPOLOGY_NUM_OF_BUSES(); bus_cnt++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_cnt);
|
|
if (tm->interface_params[if_id].
|
|
as_bus_params[bus_cnt].is_dqs_swap == 1) {
|
|
/* dqs swap */
|
|
ddr3_tip_bus_read_modify_write(dev_num, ACCESS_TYPE_UNICAST,
|
|
if_id, bus_cnt,
|
|
DDR_PHY_DATA,
|
|
PHY_CONTROL_PHY_REG, 0xc0,
|
|
0xc0);
|
|
}
|
|
|
|
if (tm->interface_params[if_id].
|
|
as_bus_params[bus_cnt].is_ck_swap == 1) {
|
|
if (bus_cnt <= 1)
|
|
data_value = 0x5 << 2;
|
|
else
|
|
data_value = 0xa << 2;
|
|
|
|
/* mask equals data */
|
|
/* ck swap pup is only control pup #0 ! */
|
|
ck_swap_pup_ctrl = 0;
|
|
ddr3_tip_bus_read_modify_write(dev_num, ACCESS_TYPE_UNICAST,
|
|
if_id, ck_swap_pup_ctrl,
|
|
DDR_PHY_CONTROL,
|
|
PHY_CONTROL_PHY_REG,
|
|
data_value, data_value);
|
|
}
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Run Training Flow
|
|
*/
|
|
int hws_ddr3_tip_run_alg(u32 dev_num, enum hws_algo_type algo_type)
|
|
{
|
|
int ret = MV_OK, ret_tune = MV_OK;
|
|
|
|
#ifdef ODT_TEST_SUPPORT
|
|
if (finger_test == 1)
|
|
return odt_test(dev_num, algo_type);
|
|
#endif
|
|
|
|
if (algo_type == ALGO_TYPE_DYNAMIC) {
|
|
ret = ddr3_tip_ddr3_auto_tune(dev_num);
|
|
} else {
|
|
#ifdef STATIC_ALGO_SUPPORT
|
|
{
|
|
enum hws_ddr_freq freq;
|
|
freq = init_freq;
|
|
|
|
/* add to mask */
|
|
if (is_adll_calib_before_init != 0) {
|
|
printf("with adll calib before init\n");
|
|
adll_calibration(dev_num, ACCESS_TYPE_MULTICAST,
|
|
0, freq);
|
|
}
|
|
/*
|
|
* Frequency per interface is not relevant,
|
|
* only interface 0
|
|
*/
|
|
ret = ddr3_tip_run_static_alg(dev_num,
|
|
freq);
|
|
}
|
|
#endif
|
|
}
|
|
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("Run_alg: tuning failed %d\n", ret_tune));
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
#ifdef ODT_TEST_SUPPORT
|
|
/*
|
|
* ODT Test
|
|
*/
|
|
static int odt_test(u32 dev_num, enum hws_algo_type algo_type)
|
|
{
|
|
int ret = MV_OK, ret_tune = MV_OK;
|
|
int pfinger_val = 0, nfinger_val;
|
|
|
|
for (pfinger_val = p_finger_start; pfinger_val <= p_finger_end;
|
|
pfinger_val += p_finger_step) {
|
|
for (nfinger_val = n_finger_start; nfinger_val <= n_finger_end;
|
|
nfinger_val += n_finger_step) {
|
|
if (finger_test != 0) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("pfinger_val %d nfinger_val %d\n",
|
|
pfinger_val, nfinger_val));
|
|
p_finger = pfinger_val;
|
|
n_finger = nfinger_val;
|
|
}
|
|
|
|
if (algo_type == ALGO_TYPE_DYNAMIC) {
|
|
ret = ddr3_tip_ddr3_auto_tune(dev_num);
|
|
} else {
|
|
/*
|
|
* Frequency per interface is not relevant,
|
|
* only interface 0
|
|
*/
|
|
ret = ddr3_tip_run_static_alg(dev_num,
|
|
init_freq);
|
|
}
|
|
}
|
|
}
|
|
|
|
if (ret_tune != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("Run_alg: tuning failed %d\n", ret_tune));
|
|
ret = (ret == MV_OK) ? ret_tune : ret;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* Select Controller
|
|
*/
|
|
int hws_ddr3_tip_select_ddr_controller(u32 dev_num, int enable)
|
|
{
|
|
if (config_func_info[dev_num].tip_dunit_mux_select_func != NULL) {
|
|
return config_func_info[dev_num].
|
|
tip_dunit_mux_select_func((u8)dev_num, enable);
|
|
}
|
|
|
|
return MV_FAIL;
|
|
}
|
|
|
|
/*
|
|
* Dunit Register Write
|
|
*/
|
|
int ddr3_tip_if_write(u32 dev_num, enum hws_access_type interface_access,
|
|
u32 if_id, u32 reg_addr, u32 data_value, u32 mask)
|
|
{
|
|
if (config_func_info[dev_num].tip_dunit_write_func != NULL) {
|
|
return config_func_info[dev_num].
|
|
tip_dunit_write_func((u8)dev_num, interface_access,
|
|
if_id, reg_addr,
|
|
data_value, mask);
|
|
}
|
|
|
|
return MV_FAIL;
|
|
}
|
|
|
|
/*
|
|
* Dunit Register Read
|
|
*/
|
|
int ddr3_tip_if_read(u32 dev_num, enum hws_access_type interface_access,
|
|
u32 if_id, u32 reg_addr, u32 *data, u32 mask)
|
|
{
|
|
if (config_func_info[dev_num].tip_dunit_read_func != NULL) {
|
|
return config_func_info[dev_num].
|
|
tip_dunit_read_func((u8)dev_num, interface_access,
|
|
if_id, reg_addr,
|
|
data, mask);
|
|
}
|
|
|
|
return MV_FAIL;
|
|
}
|
|
|
|
/*
|
|
* Dunit Register Polling
|
|
*/
|
|
int ddr3_tip_if_polling(u32 dev_num, enum hws_access_type access_type,
|
|
u32 if_id, u32 exp_value, u32 mask, u32 offset,
|
|
u32 poll_tries)
|
|
{
|
|
u32 poll_cnt = 0, interface_num = 0, start_if, end_if;
|
|
u32 read_data[MAX_INTERFACE_NUM];
|
|
int ret;
|
|
int is_fail = 0, is_if_fail;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
if (access_type == ACCESS_TYPE_MULTICAST) {
|
|
start_if = 0;
|
|
end_if = MAX_INTERFACE_NUM - 1;
|
|
} else {
|
|
start_if = if_id;
|
|
end_if = if_id;
|
|
}
|
|
|
|
for (interface_num = start_if; interface_num <= end_if; interface_num++) {
|
|
/* polling bit 3 for n times */
|
|
VALIDATE_ACTIVE(tm->if_act_mask, interface_num);
|
|
|
|
is_if_fail = 0;
|
|
for (poll_cnt = 0; poll_cnt < poll_tries; poll_cnt++) {
|
|
ret =
|
|
ddr3_tip_if_read(dev_num, ACCESS_TYPE_UNICAST,
|
|
interface_num, offset, read_data,
|
|
mask);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
|
|
if (read_data[interface_num] == exp_value)
|
|
break;
|
|
}
|
|
|
|
if (poll_cnt >= poll_tries) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("max poll IF #%d\n", interface_num));
|
|
is_fail = 1;
|
|
is_if_fail = 1;
|
|
}
|
|
|
|
training_result[training_stage][interface_num] =
|
|
(is_if_fail == 1) ? TEST_FAILED : TEST_SUCCESS;
|
|
}
|
|
|
|
return (is_fail == 0) ? MV_OK : MV_FAIL;
|
|
}
|
|
|
|
/*
|
|
* Bus read access
|
|
*/
|
|
int ddr3_tip_bus_read(u32 dev_num, u32 if_id,
|
|
enum hws_access_type phy_access, u32 phy_id,
|
|
enum hws_ddr_phy phy_type, u32 reg_addr, u32 *data)
|
|
{
|
|
u32 bus_index = 0;
|
|
u32 data_read[MAX_INTERFACE_NUM];
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
if (phy_access == ACCESS_TYPE_MULTICAST) {
|
|
for (bus_index = 0; bus_index < GET_TOPOLOGY_NUM_OF_BUSES();
|
|
bus_index++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_index);
|
|
CHECK_STATUS(ddr3_tip_bus_access
|
|
(dev_num, ACCESS_TYPE_UNICAST,
|
|
if_id, ACCESS_TYPE_UNICAST,
|
|
bus_index, phy_type, reg_addr, 0,
|
|
OPERATION_READ));
|
|
CHECK_STATUS(ddr3_tip_if_read
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
PHY_REG_FILE_ACCESS, data_read,
|
|
MASK_ALL_BITS));
|
|
data[bus_index] = (data_read[if_id] & 0xffff);
|
|
}
|
|
} else {
|
|
CHECK_STATUS(ddr3_tip_bus_access
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
phy_access, phy_id, phy_type, reg_addr, 0,
|
|
OPERATION_READ));
|
|
CHECK_STATUS(ddr3_tip_if_read
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
PHY_REG_FILE_ACCESS, data_read, MASK_ALL_BITS));
|
|
|
|
/*
|
|
* only 16 lsb bit are valid in Phy (each register is different,
|
|
* some can actually be less than 16 bits)
|
|
*/
|
|
*data = (data_read[if_id] & 0xffff);
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Bus write access
|
|
*/
|
|
int ddr3_tip_bus_write(u32 dev_num, enum hws_access_type interface_access,
|
|
u32 if_id, enum hws_access_type phy_access,
|
|
u32 phy_id, enum hws_ddr_phy phy_type, u32 reg_addr,
|
|
u32 data_value)
|
|
{
|
|
CHECK_STATUS(ddr3_tip_bus_access
|
|
(dev_num, interface_access, if_id, phy_access,
|
|
phy_id, phy_type, reg_addr, data_value, OPERATION_WRITE));
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Bus access routine (relevant for both read & write)
|
|
*/
|
|
static int ddr3_tip_bus_access(u32 dev_num, enum hws_access_type interface_access,
|
|
u32 if_id, enum hws_access_type phy_access,
|
|
u32 phy_id, enum hws_ddr_phy phy_type, u32 reg_addr,
|
|
u32 data_value, enum hws_operation oper_type)
|
|
{
|
|
u32 addr_low = 0x3f & reg_addr;
|
|
u32 addr_hi = ((0xc0 & reg_addr) >> 6);
|
|
u32 data_p1 =
|
|
(oper_type << 30) + (addr_hi << 28) + (phy_access << 27) +
|
|
(phy_type << 26) + (phy_id << 22) + (addr_low << 16) +
|
|
(data_value & 0xffff);
|
|
u32 data_p2 = data_p1 + (1 << 31);
|
|
u32 start_if, end_if;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, interface_access, if_id, PHY_REG_FILE_ACCESS,
|
|
data_p1, MASK_ALL_BITS));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, interface_access, if_id, PHY_REG_FILE_ACCESS,
|
|
data_p2, MASK_ALL_BITS));
|
|
|
|
if (interface_access == ACCESS_TYPE_UNICAST) {
|
|
start_if = if_id;
|
|
end_if = if_id;
|
|
} else {
|
|
start_if = 0;
|
|
end_if = MAX_INTERFACE_NUM - 1;
|
|
}
|
|
|
|
/* polling for read/write execution done */
|
|
for (if_id = start_if; if_id <= end_if; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
CHECK_STATUS(is_bus_access_done
|
|
(dev_num, if_id, PHY_REG_FILE_ACCESS, 31));
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Check bus access done
|
|
*/
|
|
static int is_bus_access_done(u32 dev_num, u32 if_id, u32 dunit_reg_adrr,
|
|
u32 bit)
|
|
{
|
|
u32 rd_data = 1;
|
|
u32 cnt = 0;
|
|
u32 data_read[MAX_INTERFACE_NUM];
|
|
|
|
CHECK_STATUS(ddr3_tip_if_read
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id, dunit_reg_adrr,
|
|
data_read, MASK_ALL_BITS));
|
|
rd_data = data_read[if_id];
|
|
rd_data &= (1 << bit);
|
|
|
|
while (rd_data != 0) {
|
|
if (cnt++ >= MAX_POLLING_ITERATIONS)
|
|
break;
|
|
|
|
CHECK_STATUS(ddr3_tip_if_read
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
dunit_reg_adrr, data_read, MASK_ALL_BITS));
|
|
rd_data = data_read[if_id];
|
|
rd_data &= (1 << bit);
|
|
}
|
|
|
|
if (cnt < MAX_POLLING_ITERATIONS)
|
|
return MV_OK;
|
|
else
|
|
return MV_FAIL;
|
|
}
|
|
|
|
/*
|
|
* Phy read-modify-write
|
|
*/
|
|
int ddr3_tip_bus_read_modify_write(u32 dev_num, enum hws_access_type access_type,
|
|
u32 interface_id, u32 phy_id,
|
|
enum hws_ddr_phy phy_type, u32 reg_addr,
|
|
u32 data_value, u32 reg_mask)
|
|
{
|
|
u32 data_val = 0, if_id, start_if, end_if;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
if (access_type == ACCESS_TYPE_MULTICAST) {
|
|
start_if = 0;
|
|
end_if = MAX_INTERFACE_NUM - 1;
|
|
} else {
|
|
start_if = interface_id;
|
|
end_if = interface_id;
|
|
}
|
|
|
|
for (if_id = start_if; if_id <= end_if; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
CHECK_STATUS(ddr3_tip_bus_read
|
|
(dev_num, if_id, ACCESS_TYPE_UNICAST, phy_id,
|
|
phy_type, reg_addr, &data_val));
|
|
data_value = (data_val & (~reg_mask)) | (data_value & reg_mask);
|
|
CHECK_STATUS(ddr3_tip_bus_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
ACCESS_TYPE_UNICAST, phy_id, phy_type, reg_addr,
|
|
data_value));
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* ADLL Calibration
|
|
*/
|
|
int adll_calibration(u32 dev_num, enum hws_access_type access_type,
|
|
u32 if_id, enum hws_ddr_freq frequency)
|
|
{
|
|
struct hws_tip_freq_config_info freq_config_info;
|
|
u32 bus_cnt = 0;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
/* Reset Diver_b assert -> de-assert */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, SDRAM_CONFIGURATION_REG,
|
|
0, 0x10000000));
|
|
mdelay(10);
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, SDRAM_CONFIGURATION_REG,
|
|
0x10000000, 0x10000000));
|
|
|
|
if (config_func_info[dev_num].tip_get_freq_config_info_func != NULL) {
|
|
CHECK_STATUS(config_func_info[dev_num].
|
|
tip_get_freq_config_info_func((u8)dev_num, frequency,
|
|
&freq_config_info));
|
|
} else {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("tip_get_freq_config_info_func is NULL"));
|
|
return MV_NOT_INITIALIZED;
|
|
}
|
|
|
|
for (bus_cnt = 0; bus_cnt < GET_TOPOLOGY_NUM_OF_BUSES(); bus_cnt++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_cnt);
|
|
CHECK_STATUS(ddr3_tip_bus_read_modify_write
|
|
(dev_num, access_type, if_id, bus_cnt,
|
|
DDR_PHY_DATA, BW_PHY_REG,
|
|
freq_config_info.bw_per_freq << 8, 0x700));
|
|
CHECK_STATUS(ddr3_tip_bus_read_modify_write
|
|
(dev_num, access_type, if_id, bus_cnt,
|
|
DDR_PHY_DATA, RATE_PHY_REG,
|
|
freq_config_info.rate_per_freq, 0x7));
|
|
}
|
|
|
|
/* DUnit to Phy drive post edge, ADLL reset assert de-assert */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, DRAM_PHY_CONFIGURATION,
|
|
0, (0x80000000 | 0x40000000)));
|
|
mdelay(100 / (freq_val[frequency] / freq_val[DDR_FREQ_LOW_FREQ]));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, DRAM_PHY_CONFIGURATION,
|
|
(0x80000000 | 0x40000000), (0x80000000 | 0x40000000)));
|
|
|
|
/* polling for ADLL Done */
|
|
if (ddr3_tip_if_polling(dev_num, access_type, if_id,
|
|
0x3ff03ff, 0x3ff03ff, PHY_LOCK_STATUS_REG,
|
|
MAX_POLLING_ITERATIONS) != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("Freq_set: DDR3 poll failed(1)"));
|
|
}
|
|
|
|
/* pup data_pup reset assert-> deassert */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, SDRAM_CONFIGURATION_REG,
|
|
0, 0x60000000));
|
|
mdelay(10);
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, SDRAM_CONFIGURATION_REG,
|
|
0x60000000, 0x60000000));
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
int ddr3_tip_freq_set(u32 dev_num, enum hws_access_type access_type,
|
|
u32 if_id, enum hws_ddr_freq frequency)
|
|
{
|
|
u32 cl_value = 0, cwl_value = 0, mem_mask = 0, val = 0,
|
|
bus_cnt = 0, t_hclk = 0, t_wr = 0,
|
|
refresh_interval_cnt = 0, cnt_id;
|
|
u32 t_refi = 0, end_if, start_if;
|
|
u32 bus_index = 0;
|
|
int is_dll_off = 0;
|
|
enum hws_speed_bin speed_bin_index = 0;
|
|
struct hws_tip_freq_config_info freq_config_info;
|
|
enum hws_result *flow_result = training_result[training_stage];
|
|
u32 adll_tap = 0;
|
|
u32 cs_mask[MAX_INTERFACE_NUM];
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE,
|
|
("dev %d access %d IF %d freq %d\n", dev_num,
|
|
access_type, if_id, frequency));
|
|
|
|
if (frequency == DDR_FREQ_LOW_FREQ)
|
|
is_dll_off = 1;
|
|
if (access_type == ACCESS_TYPE_MULTICAST) {
|
|
start_if = 0;
|
|
end_if = MAX_INTERFACE_NUM - 1;
|
|
} else {
|
|
start_if = if_id;
|
|
end_if = if_id;
|
|
}
|
|
|
|
/* calculate interface cs mask - Oferb 4/11 */
|
|
/* speed bin can be different for each interface */
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
/* cs enable is active low */
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
cs_mask[if_id] = CS_BIT_MASK;
|
|
training_result[training_stage][if_id] = TEST_SUCCESS;
|
|
ddr3_tip_calc_cs_mask(dev_num, if_id, effective_cs,
|
|
&cs_mask[if_id]);
|
|
}
|
|
|
|
/* speed bin can be different for each interface */
|
|
/*
|
|
* moti b - need to remove the loop for multicas access functions
|
|
* and loop the unicast access functions
|
|
*/
|
|
for (if_id = start_if; if_id <= end_if; if_id++) {
|
|
if (IS_ACTIVE(tm->if_act_mask, if_id) == 0)
|
|
continue;
|
|
|
|
flow_result[if_id] = TEST_SUCCESS;
|
|
speed_bin_index =
|
|
tm->interface_params[if_id].speed_bin_index;
|
|
if (tm->interface_params[if_id].memory_freq ==
|
|
frequency) {
|
|
cl_value =
|
|
tm->interface_params[if_id].cas_l;
|
|
cwl_value =
|
|
tm->interface_params[if_id].cas_wl;
|
|
} else {
|
|
cl_value =
|
|
cas_latency_table[speed_bin_index].cl_val[frequency];
|
|
cwl_value =
|
|
cas_write_latency_table[speed_bin_index].
|
|
cl_val[frequency];
|
|
}
|
|
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE,
|
|
("Freq_set dev 0x%x access 0x%x if 0x%x freq 0x%x speed %d:\n\t",
|
|
dev_num, access_type, if_id,
|
|
frequency, speed_bin_index));
|
|
|
|
for (cnt_id = 0; cnt_id < DDR_FREQ_LIMIT; cnt_id++) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE,
|
|
("%d ",
|
|
cas_latency_table[speed_bin_index].
|
|
cl_val[cnt_id]));
|
|
}
|
|
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_TRACE, ("\n"));
|
|
mem_mask = 0;
|
|
for (bus_index = 0; bus_index < GET_TOPOLOGY_NUM_OF_BUSES();
|
|
bus_index++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_index);
|
|
mem_mask |=
|
|
tm->interface_params[if_id].
|
|
as_bus_params[bus_index].mirror_enable_bitmask;
|
|
}
|
|
|
|
if (mem_mask != 0) {
|
|
/* motib redundent in KW28 */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type,
|
|
if_id,
|
|
CS_ENABLE_REG, 0, 0x8));
|
|
}
|
|
|
|
/* dll state after exiting SR */
|
|
if (is_dll_off == 1) {
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DFS_REG, 0x1, 0x1));
|
|
} else {
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DFS_REG, 0, 0x1));
|
|
}
|
|
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DUNIT_MMASK_REG, 0, 0x1));
|
|
/* DFS - block transactions */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DFS_REG, 0x2, 0x2));
|
|
|
|
/* disable ODT in case of dll off */
|
|
if (is_dll_off == 1) {
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
0x1874, 0, 0x244));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
0x1884, 0, 0x244));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
0x1894, 0, 0x244));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
0x18a4, 0, 0x244));
|
|
}
|
|
|
|
/* DFS - Enter Self-Refresh */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, DFS_REG, 0x4,
|
|
0x4));
|
|
/* polling on self refresh entry */
|
|
if (ddr3_tip_if_polling(dev_num, ACCESS_TYPE_UNICAST,
|
|
if_id, 0x8, 0x8, DFS_REG,
|
|
MAX_POLLING_ITERATIONS) != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("Freq_set: DDR3 poll failed on SR entry\n"));
|
|
}
|
|
|
|
/* PLL configuration */
|
|
if (config_func_info[dev_num].tip_set_freq_divider_func != NULL) {
|
|
config_func_info[dev_num].
|
|
tip_set_freq_divider_func(dev_num, if_id,
|
|
frequency);
|
|
}
|
|
|
|
/* PLL configuration End */
|
|
|
|
/* adjust t_refi to new frequency */
|
|
t_refi = (tm->interface_params[if_id].interface_temp ==
|
|
HWS_TEMP_HIGH) ? TREFI_LOW : TREFI_HIGH;
|
|
t_refi *= 1000; /*psec */
|
|
|
|
/* HCLK in[ps] */
|
|
t_hclk = MEGA / (freq_val[frequency] / 2);
|
|
refresh_interval_cnt = t_refi / t_hclk; /* no units */
|
|
val = 0x4000 | refresh_interval_cnt;
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
SDRAM_CONFIGURATION_REG, val, 0x7fff));
|
|
|
|
/* DFS - CL/CWL/WR parameters after exiting SR */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, DFS_REG,
|
|
(cl_mask_table[cl_value] << 8), 0xf00));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, DFS_REG,
|
|
(cwl_mask_table[cwl_value] << 12), 0x7000));
|
|
t_wr = speed_bin_table(speed_bin_index, SPEED_BIN_TWR);
|
|
t_wr = (t_wr / 1000);
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, DFS_REG,
|
|
(twr_mask_table[t_wr + 1] << 16), 0x70000));
|
|
|
|
/* Restore original RTT values if returning from DLL OFF mode */
|
|
if (is_dll_off == 1) {
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, 0x1874,
|
|
g_dic | g_rtt_nom, 0x266));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, 0x1884,
|
|
g_dic | g_rtt_nom, 0x266));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, 0x1894,
|
|
g_dic | g_rtt_nom, 0x266));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, 0x18a4,
|
|
g_dic | g_rtt_nom, 0x266));
|
|
}
|
|
|
|
/* Reset Diver_b assert -> de-assert */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
SDRAM_CONFIGURATION_REG, 0, 0x10000000));
|
|
mdelay(10);
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
SDRAM_CONFIGURATION_REG, 0x10000000, 0x10000000));
|
|
|
|
/* Adll configuration function of process and Frequency */
|
|
if (config_func_info[dev_num].tip_get_freq_config_info_func != NULL) {
|
|
CHECK_STATUS(config_func_info[dev_num].
|
|
tip_get_freq_config_info_func(dev_num, frequency,
|
|
&freq_config_info));
|
|
}
|
|
/* TBD check milo5 using device ID ? */
|
|
for (bus_cnt = 0; bus_cnt < GET_TOPOLOGY_NUM_OF_BUSES();
|
|
bus_cnt++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_cnt);
|
|
CHECK_STATUS(ddr3_tip_bus_read_modify_write
|
|
(dev_num, ACCESS_TYPE_UNICAST,
|
|
if_id, bus_cnt, DDR_PHY_DATA,
|
|
0x92,
|
|
freq_config_info.
|
|
bw_per_freq << 8
|
|
/*freq_mask[dev_num][frequency] << 8 */
|
|
, 0x700));
|
|
CHECK_STATUS(ddr3_tip_bus_read_modify_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
bus_cnt, DDR_PHY_DATA, 0x94,
|
|
freq_config_info.rate_per_freq, 0x7));
|
|
}
|
|
|
|
/* DUnit to Phy drive post edge, ADLL reset assert de-assert */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DRAM_PHY_CONFIGURATION, 0,
|
|
(0x80000000 | 0x40000000)));
|
|
mdelay(100 / (freq_val[frequency] / freq_val[DDR_FREQ_LOW_FREQ]));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
DRAM_PHY_CONFIGURATION, (0x80000000 | 0x40000000),
|
|
(0x80000000 | 0x40000000)));
|
|
|
|
/* polling for ADLL Done */
|
|
if (ddr3_tip_if_polling
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id, 0x3ff03ff,
|
|
0x3ff03ff, PHY_LOCK_STATUS_REG,
|
|
MAX_POLLING_ITERATIONS) != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("Freq_set: DDR3 poll failed(1)\n"));
|
|
}
|
|
|
|
/* pup data_pup reset assert-> deassert */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
SDRAM_CONFIGURATION_REG, 0, 0x60000000));
|
|
mdelay(10);
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
SDRAM_CONFIGURATION_REG, 0x60000000, 0x60000000));
|
|
|
|
/* Set proper timing params before existing Self-Refresh */
|
|
ddr3_tip_set_timing(dev_num, access_type, if_id, frequency);
|
|
if (delay_enable != 0) {
|
|
adll_tap = MEGA / (freq_val[frequency] * 64);
|
|
ddr3_tip_cmd_addr_init_delay(dev_num, adll_tap);
|
|
}
|
|
|
|
/* Exit SR */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, DFS_REG, 0,
|
|
0x4));
|
|
if (ddr3_tip_if_polling
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id, 0, 0x8, DFS_REG,
|
|
MAX_POLLING_ITERATIONS) != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("Freq_set: DDR3 poll failed(2)"));
|
|
}
|
|
|
|
/* Refresh Command */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id,
|
|
SDRAM_OPERATION_REG, 0x2, 0xf1f));
|
|
if (ddr3_tip_if_polling
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id, 0, 0x1f,
|
|
SDRAM_OPERATION_REG, MAX_POLLING_ITERATIONS) != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("Freq_set: DDR3 poll failed(3)"));
|
|
}
|
|
|
|
/* Release DFS Block */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, DFS_REG, 0,
|
|
0x2));
|
|
/* Controller to MBUS Retry - normal */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, DUNIT_MMASK_REG,
|
|
0x1, 0x1));
|
|
|
|
/* MRO: Burst Length 8, CL , Auto_precharge 0x16cc */
|
|
val =
|
|
((cl_mask_table[cl_value] & 0x1) << 2) |
|
|
((cl_mask_table[cl_value] & 0xe) << 3);
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, access_type, if_id, MR0_REG,
|
|
val, (0x7 << 4) | (1 << 2)));
|
|
/* MR2: CWL = 10 , Auto Self-Refresh - disable */
|
|
val = (cwl_mask_table[cwl_value] << 3);
|
|
/*
|
|
* nklein 24.10.13 - should not be here - leave value as set in
|
|
* the init configuration val |= (1 << 9);
|
|
* val |= ((tm->interface_params[if_id].
|
|
* interface_temp == HWS_TEMP_HIGH) ? (1 << 7) : 0);
|
|
*/
|
|
/* nklein 24.10.13 - see above comment */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type,
|
|
if_id, MR2_REG,
|
|
val, (0x7 << 3)));
|
|
|
|
/* ODT TIMING */
|
|
val = ((cl_value - cwl_value + 1) << 4) |
|
|
((cl_value - cwl_value + 6) << 8) |
|
|
((cl_value - 1) << 12) | ((cl_value + 6) << 16);
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type,
|
|
if_id, ODT_TIMING_LOW,
|
|
val, 0xffff0));
|
|
val = 0x71 | ((cwl_value - 1) << 8) | ((cwl_value + 5) << 12);
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type,
|
|
if_id, ODT_TIMING_HI_REG,
|
|
val, 0xffff));
|
|
|
|
/* ODT Active */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type,
|
|
if_id,
|
|
DUNIT_ODT_CONTROL_REG,
|
|
0xf, 0xf));
|
|
|
|
/* re-write CL */
|
|
val = ((cl_mask_table[cl_value] & 0x1) << 2) |
|
|
((cl_mask_table[cl_value] & 0xe) << 3);
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
0, MR0_REG, val,
|
|
(0x7 << 4) | (1 << 2)));
|
|
|
|
/* re-write CWL */
|
|
val = (cwl_mask_table[cwl_value] << 3);
|
|
CHECK_STATUS(ddr3_tip_write_mrs_cmd(dev_num, cs_mask, MRS2_CMD,
|
|
val, (0x7 << 3)));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
0, MR2_REG, val, (0x7 << 3)));
|
|
|
|
if (mem_mask != 0) {
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type,
|
|
if_id,
|
|
CS_ENABLE_REG,
|
|
1 << 3, 0x8));
|
|
}
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Set ODT values
|
|
*/
|
|
static int ddr3_tip_write_odt(u32 dev_num, enum hws_access_type access_type,
|
|
u32 if_id, u32 cl_value, u32 cwl_value)
|
|
{
|
|
/* ODT TIMING */
|
|
u32 val = (cl_value - cwl_value + 6);
|
|
|
|
val = ((cl_value - cwl_value + 1) << 4) | ((val & 0xf) << 8) |
|
|
(((cl_value - 1) & 0xf) << 12) |
|
|
(((cl_value + 6) & 0xf) << 16) | (((val & 0x10) >> 4) << 21);
|
|
val |= (((cl_value - 1) >> 4) << 22) | (((cl_value + 6) >> 4) << 23);
|
|
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
ODT_TIMING_LOW, val, 0xffff0));
|
|
val = 0x71 | ((cwl_value - 1) << 8) | ((cwl_value + 5) << 12);
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
ODT_TIMING_HI_REG, val, 0xffff));
|
|
if (odt_additional == 1) {
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type,
|
|
if_id,
|
|
SDRAM_ODT_CONTROL_HIGH_REG,
|
|
0xf, 0xf));
|
|
}
|
|
|
|
/* ODT Active */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
DUNIT_ODT_CONTROL_REG, 0xf, 0xf));
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Set Timing values for training
|
|
*/
|
|
static int ddr3_tip_set_timing(u32 dev_num, enum hws_access_type access_type,
|
|
u32 if_id, enum hws_ddr_freq frequency)
|
|
{
|
|
u32 t_ckclk = 0, t_ras = 0;
|
|
u32 t_rcd = 0, t_rp = 0, t_wr = 0, t_wtr = 0, t_rrd = 0, t_rtp = 0,
|
|
t_rfc = 0, t_mod = 0;
|
|
u32 val = 0, page_size = 0;
|
|
enum hws_speed_bin speed_bin_index;
|
|
enum hws_mem_size memory_size = MEM_2G;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
speed_bin_index = tm->interface_params[if_id].speed_bin_index;
|
|
memory_size = tm->interface_params[if_id].memory_size;
|
|
page_size =
|
|
(tm->interface_params[if_id].bus_width ==
|
|
BUS_WIDTH_8) ? page_param[memory_size].
|
|
page_size_8bit : page_param[memory_size].page_size_16bit;
|
|
t_ckclk = (MEGA / freq_val[frequency]);
|
|
t_rrd = (page_size == 1) ? speed_bin_table(speed_bin_index,
|
|
SPEED_BIN_TRRD1K) :
|
|
speed_bin_table(speed_bin_index, SPEED_BIN_TRRD2K);
|
|
t_rrd = GET_MAX_VALUE(t_ckclk * 4, t_rrd);
|
|
t_rtp = GET_MAX_VALUE(t_ckclk * 4, speed_bin_table(speed_bin_index,
|
|
SPEED_BIN_TRTP));
|
|
t_wtr = GET_MAX_VALUE(t_ckclk * 4, speed_bin_table(speed_bin_index,
|
|
SPEED_BIN_TWTR));
|
|
t_ras = TIME_2_CLOCK_CYCLES(speed_bin_table(speed_bin_index,
|
|
SPEED_BIN_TRAS),
|
|
t_ckclk);
|
|
t_rcd = TIME_2_CLOCK_CYCLES(speed_bin_table(speed_bin_index,
|
|
SPEED_BIN_TRCD),
|
|
t_ckclk);
|
|
t_rp = TIME_2_CLOCK_CYCLES(speed_bin_table(speed_bin_index,
|
|
SPEED_BIN_TRP),
|
|
t_ckclk);
|
|
t_wr = TIME_2_CLOCK_CYCLES(speed_bin_table(speed_bin_index,
|
|
SPEED_BIN_TWR),
|
|
t_ckclk);
|
|
t_wtr = TIME_2_CLOCK_CYCLES(t_wtr, t_ckclk);
|
|
t_rrd = TIME_2_CLOCK_CYCLES(t_rrd, t_ckclk);
|
|
t_rtp = TIME_2_CLOCK_CYCLES(t_rtp, t_ckclk);
|
|
t_rfc = TIME_2_CLOCK_CYCLES(rfc_table[memory_size] * 1000, t_ckclk);
|
|
t_mod = GET_MAX_VALUE(t_ckclk * 24, 15000);
|
|
t_mod = TIME_2_CLOCK_CYCLES(t_mod, t_ckclk);
|
|
|
|
/* SDRAM Timing Low */
|
|
val = (t_ras & 0xf) | (t_rcd << 4) | (t_rp << 8) | (t_wr << 12) |
|
|
(t_wtr << 16) | (((t_ras & 0x30) >> 4) << 20) | (t_rrd << 24) |
|
|
(t_rtp << 28);
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_LOW_REG, val, 0xff3fffff));
|
|
|
|
/* SDRAM Timing High */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_HIGH_REG,
|
|
t_rfc & 0x7f, 0x7f));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_HIGH_REG,
|
|
0x180, 0x180));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_HIGH_REG,
|
|
0x600, 0x600));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_HIGH_REG,
|
|
0x1800, 0xf800));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_HIGH_REG,
|
|
((t_rfc & 0x380) >> 7) << 16, 0x70000));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_HIGH_REG, 0,
|
|
0x380000));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_HIGH_REG,
|
|
(t_mod & 0xf) << 25, 0x1e00000));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_HIGH_REG,
|
|
(t_mod >> 4) << 30, 0xc0000000));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_HIGH_REG,
|
|
0x16000000, 0x1e000000));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
SDRAM_TIMING_HIGH_REG,
|
|
0x40000000, 0xc0000000));
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Mode Read
|
|
*/
|
|
int hws_ddr3_tip_mode_read(u32 dev_num, struct mode_info *mode_info)
|
|
{
|
|
u32 ret;
|
|
|
|
ret = ddr3_tip_if_read(dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
|
|
MR0_REG, mode_info->reg_mr0, MASK_ALL_BITS);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
|
|
ret = ddr3_tip_if_read(dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
|
|
MR1_REG, mode_info->reg_mr1, MASK_ALL_BITS);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
|
|
ret = ddr3_tip_if_read(dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
|
|
MR2_REG, mode_info->reg_mr2, MASK_ALL_BITS);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
|
|
ret = ddr3_tip_if_read(dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
|
|
MR3_REG, mode_info->reg_mr2, MASK_ALL_BITS);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
|
|
ret = ddr3_tip_if_read(dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
|
|
READ_DATA_SAMPLE_DELAY, mode_info->read_data_sample,
|
|
MASK_ALL_BITS);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
|
|
ret = ddr3_tip_if_read(dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
|
|
READ_DATA_READY_DELAY, mode_info->read_data_ready,
|
|
MASK_ALL_BITS);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Get first active IF
|
|
*/
|
|
int ddr3_tip_get_first_active_if(u8 dev_num, u32 interface_mask,
|
|
u32 *interface_id)
|
|
{
|
|
u32 if_id;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
if (interface_mask & (1 << if_id)) {
|
|
*interface_id = if_id;
|
|
break;
|
|
}
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Write CS Result
|
|
*/
|
|
int ddr3_tip_write_cs_result(u32 dev_num, u32 offset)
|
|
{
|
|
u32 if_id, bus_num, cs_bitmask, data_val, cs_num;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
for (bus_num = 0; bus_num < tm->num_of_bus_per_interface;
|
|
bus_num++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_num);
|
|
cs_bitmask =
|
|
tm->interface_params[if_id].
|
|
as_bus_params[bus_num].cs_bitmask;
|
|
if (cs_bitmask != effective_cs) {
|
|
cs_num = GET_CS_FROM_MASK(cs_bitmask);
|
|
ddr3_tip_bus_read(dev_num, if_id,
|
|
ACCESS_TYPE_UNICAST, bus_num,
|
|
DDR_PHY_DATA,
|
|
offset +
|
|
CS_REG_VALUE(effective_cs),
|
|
&data_val);
|
|
ddr3_tip_bus_write(dev_num,
|
|
ACCESS_TYPE_UNICAST,
|
|
if_id,
|
|
ACCESS_TYPE_UNICAST,
|
|
bus_num, DDR_PHY_DATA,
|
|
offset +
|
|
CS_REG_VALUE(cs_num),
|
|
data_val);
|
|
}
|
|
}
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Write MRS
|
|
*/
|
|
int ddr3_tip_write_mrs_cmd(u32 dev_num, u32 *cs_mask_arr, u32 cmd,
|
|
u32 data, u32 mask)
|
|
{
|
|
u32 if_id, reg;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
reg = (cmd == MRS1_CMD) ? MR1_REG : MR2_REG;
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
PARAM_NOT_CARE, reg, data, mask));
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
SDRAM_OPERATION_REG,
|
|
(cs_mask_arr[if_id] << 8) | cmd, 0xf1f));
|
|
}
|
|
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
if (ddr3_tip_if_polling(dev_num, ACCESS_TYPE_UNICAST, if_id, 0,
|
|
0x1f, SDRAM_OPERATION_REG,
|
|
MAX_POLLING_ITERATIONS) != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("write_mrs_cmd: Poll cmd fail"));
|
|
}
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Reset XSB Read FIFO
|
|
*/
|
|
int ddr3_tip_reset_fifo_ptr(u32 dev_num)
|
|
{
|
|
u32 if_id = 0;
|
|
|
|
/* Configure PHY reset value to 0 in order to "clean" the FIFO */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
if_id, 0x15c8, 0, 0xff000000));
|
|
/*
|
|
* Move PHY to RL mode (only in RL mode the PHY overrides FIFO values
|
|
* during FIFO reset)
|
|
*/
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
if_id, TRAINING_SW_2_REG,
|
|
0x1, 0x9));
|
|
/* In order that above configuration will influence the PHY */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
if_id, 0x15b0,
|
|
0x80000000, 0x80000000));
|
|
/* Reset read fifo assertion */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
if_id, 0x1400, 0, 0x40000000));
|
|
/* Reset read fifo deassertion */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
if_id, 0x1400,
|
|
0x40000000, 0x40000000));
|
|
/* Move PHY back to functional mode */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
if_id, TRAINING_SW_2_REG,
|
|
0x8, 0x9));
|
|
/* Stop training machine */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
if_id, 0x15b4, 0x10000, 0x10000));
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Reset Phy registers
|
|
*/
|
|
int ddr3_tip_ddr3_reset_phy_regs(u32 dev_num)
|
|
{
|
|
u32 if_id, phy_id, cs;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
for (phy_id = 0; phy_id < tm->num_of_bus_per_interface;
|
|
phy_id++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, phy_id);
|
|
CHECK_STATUS(ddr3_tip_bus_write
|
|
(dev_num, ACCESS_TYPE_UNICAST,
|
|
if_id, ACCESS_TYPE_UNICAST,
|
|
phy_id, DDR_PHY_DATA,
|
|
WL_PHY_REG +
|
|
CS_REG_VALUE(effective_cs),
|
|
phy_reg0_val));
|
|
CHECK_STATUS(ddr3_tip_bus_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
ACCESS_TYPE_UNICAST, phy_id, DDR_PHY_DATA,
|
|
RL_PHY_REG + CS_REG_VALUE(effective_cs),
|
|
phy_reg2_val));
|
|
CHECK_STATUS(ddr3_tip_bus_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
ACCESS_TYPE_UNICAST, phy_id, DDR_PHY_DATA,
|
|
READ_CENTRALIZATION_PHY_REG +
|
|
CS_REG_VALUE(effective_cs), phy_reg3_val));
|
|
CHECK_STATUS(ddr3_tip_bus_write
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
ACCESS_TYPE_UNICAST, phy_id, DDR_PHY_DATA,
|
|
WRITE_CENTRALIZATION_PHY_REG +
|
|
CS_REG_VALUE(effective_cs), phy_reg3_val));
|
|
}
|
|
}
|
|
|
|
/* Set Receiver Calibration value */
|
|
for (cs = 0; cs < MAX_CS_NUM; cs++) {
|
|
/* PHY register 0xdb bits[5:0] - configure to 63 */
|
|
CHECK_STATUS(ddr3_tip_bus_write
|
|
(dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
|
|
ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
|
|
DDR_PHY_DATA, CSN_IOB_VREF_REG(cs), 63));
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Restore Dunit registers
|
|
*/
|
|
int ddr3_tip_restore_dunit_regs(u32 dev_num)
|
|
{
|
|
u32 index_cnt;
|
|
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
PARAM_NOT_CARE, CALIB_MACHINE_CTRL_REG,
|
|
0x1, 0x1));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
PARAM_NOT_CARE, CALIB_MACHINE_CTRL_REG,
|
|
calibration_update_control << 3,
|
|
0x3 << 3));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST,
|
|
PARAM_NOT_CARE,
|
|
ODPG_WRITE_READ_MODE_ENABLE_REG,
|
|
0xffff, MASK_ALL_BITS));
|
|
|
|
for (index_cnt = 0; index_cnt < ARRAY_SIZE(odpg_default_value);
|
|
index_cnt++) {
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
|
|
odpg_default_value[index_cnt].reg_addr,
|
|
odpg_default_value[index_cnt].reg_data,
|
|
odpg_default_value[index_cnt].reg_mask));
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Auto tune main flow
|
|
*/
|
|
static int ddr3_tip_ddr3_training_main_flow(u32 dev_num)
|
|
{
|
|
enum hws_ddr_freq freq = init_freq;
|
|
struct init_cntr_param init_cntr_prm;
|
|
int ret = MV_OK;
|
|
u32 if_id;
|
|
u32 max_cs = hws_ddr3_tip_max_cs_get();
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
#ifndef EXCLUDE_SWITCH_DEBUG
|
|
if (debug_training == DEBUG_LEVEL_TRACE) {
|
|
CHECK_STATUS(print_device_info((u8)dev_num));
|
|
}
|
|
#endif
|
|
|
|
for (effective_cs = 0; effective_cs < max_cs; effective_cs++) {
|
|
CHECK_STATUS(ddr3_tip_ddr3_reset_phy_regs(dev_num));
|
|
}
|
|
/* Set to 0 after each loop to avoid illegal value may be used */
|
|
effective_cs = 0;
|
|
|
|
freq = init_freq;
|
|
if (is_pll_before_init != 0) {
|
|
for (if_id = 0; if_id < MAX_INTERFACE_NUM; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
config_func_info[dev_num].tip_set_freq_divider_func(
|
|
(u8)dev_num, if_id, freq);
|
|
}
|
|
}
|
|
|
|
if (is_adll_calib_before_init != 0) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("with adll calib before init\n"));
|
|
adll_calibration(dev_num, ACCESS_TYPE_MULTICAST, 0, freq);
|
|
}
|
|
|
|
if (is_reg_dump != 0) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("Dump before init controller\n"));
|
|
ddr3_tip_reg_dump(dev_num);
|
|
}
|
|
|
|
if (mask_tune_func & INIT_CONTROLLER_MASK_BIT) {
|
|
training_stage = INIT_CONTROLLER;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("INIT_CONTROLLER_MASK_BIT\n"));
|
|
init_cntr_prm.do_mrs_phy = 1;
|
|
init_cntr_prm.is_ctrl64_bit = 0;
|
|
init_cntr_prm.init_phy = 1;
|
|
init_cntr_prm.msys_init = 0;
|
|
ret = hws_ddr3_tip_init_controller(dev_num, &init_cntr_prm);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("hws_ddr3_tip_init_controller failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
#ifdef STATIC_ALGO_SUPPORT
|
|
if (mask_tune_func & STATIC_LEVELING_MASK_BIT) {
|
|
training_stage = STATIC_LEVELING;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("STATIC_LEVELING_MASK_BIT\n"));
|
|
ret = ddr3_tip_run_static_alg(dev_num, freq);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_run_static_alg failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
if (mask_tune_func & SET_LOW_FREQ_MASK_BIT) {
|
|
training_stage = SET_LOW_FREQ;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("SET_LOW_FREQ_MASK_BIT %d\n",
|
|
freq_val[low_freq]));
|
|
ret = ddr3_tip_freq_set(dev_num, ACCESS_TYPE_MULTICAST,
|
|
PARAM_NOT_CARE, low_freq);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_freq_set failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
for (effective_cs = 0; effective_cs < max_cs; effective_cs++) {
|
|
if (mask_tune_func & LOAD_PATTERN_MASK_BIT) {
|
|
training_stage = LOAD_PATTERN;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("LOAD_PATTERN_MASK_BIT #%d\n",
|
|
effective_cs));
|
|
ret = ddr3_tip_load_all_pattern_to_mem(dev_num);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_load_all_pattern_to_mem failure CS #%d\n",
|
|
effective_cs));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
}
|
|
/* Set to 0 after each loop to avoid illegal value may be used */
|
|
effective_cs = 0;
|
|
|
|
if (mask_tune_func & SET_MEDIUM_FREQ_MASK_BIT) {
|
|
training_stage = SET_MEDIUM_FREQ;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("SET_MEDIUM_FREQ_MASK_BIT %d\n",
|
|
freq_val[medium_freq]));
|
|
ret =
|
|
ddr3_tip_freq_set(dev_num, ACCESS_TYPE_MULTICAST,
|
|
PARAM_NOT_CARE, medium_freq);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_freq_set failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
if (mask_tune_func & WRITE_LEVELING_MASK_BIT) {
|
|
training_stage = WRITE_LEVELING;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("WRITE_LEVELING_MASK_BIT\n"));
|
|
if ((rl_mid_freq_wa == 0) || (freq_val[medium_freq] == 533)) {
|
|
ret = ddr3_tip_dynamic_write_leveling(dev_num);
|
|
} else {
|
|
/* Use old WL */
|
|
ret = ddr3_tip_legacy_dynamic_write_leveling(dev_num);
|
|
}
|
|
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_dynamic_write_leveling failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
for (effective_cs = 0; effective_cs < max_cs; effective_cs++) {
|
|
if (mask_tune_func & LOAD_PATTERN_2_MASK_BIT) {
|
|
training_stage = LOAD_PATTERN_2;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("LOAD_PATTERN_2_MASK_BIT CS #%d\n",
|
|
effective_cs));
|
|
ret = ddr3_tip_load_all_pattern_to_mem(dev_num);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_load_all_pattern_to_mem failure CS #%d\n",
|
|
effective_cs));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
}
|
|
/* Set to 0 after each loop to avoid illegal value may be used */
|
|
effective_cs = 0;
|
|
|
|
if (mask_tune_func & READ_LEVELING_MASK_BIT) {
|
|
training_stage = READ_LEVELING;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("READ_LEVELING_MASK_BIT\n"));
|
|
if ((rl_mid_freq_wa == 0) || (freq_val[medium_freq] == 533)) {
|
|
ret = ddr3_tip_dynamic_read_leveling(dev_num, medium_freq);
|
|
} else {
|
|
/* Use old RL */
|
|
ret = ddr3_tip_legacy_dynamic_read_leveling(dev_num);
|
|
}
|
|
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_dynamic_read_leveling failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
if (mask_tune_func & WRITE_LEVELING_SUPP_MASK_BIT) {
|
|
training_stage = WRITE_LEVELING_SUPP;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("WRITE_LEVELING_SUPP_MASK_BIT\n"));
|
|
ret = ddr3_tip_dynamic_write_leveling_supp(dev_num);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_dynamic_write_leveling_supp failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
for (effective_cs = 0; effective_cs < max_cs; effective_cs++) {
|
|
if (mask_tune_func & PBS_RX_MASK_BIT) {
|
|
training_stage = PBS_RX;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("PBS_RX_MASK_BIT CS #%d\n",
|
|
effective_cs));
|
|
ret = ddr3_tip_pbs_rx(dev_num);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_pbs_rx failure CS #%d\n",
|
|
effective_cs));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
}
|
|
|
|
for (effective_cs = 0; effective_cs < max_cs; effective_cs++) {
|
|
if (mask_tune_func & PBS_TX_MASK_BIT) {
|
|
training_stage = PBS_TX;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("PBS_TX_MASK_BIT CS #%d\n",
|
|
effective_cs));
|
|
ret = ddr3_tip_pbs_tx(dev_num);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_pbs_tx failure CS #%d\n",
|
|
effective_cs));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
}
|
|
/* Set to 0 after each loop to avoid illegal value may be used */
|
|
effective_cs = 0;
|
|
|
|
if (mask_tune_func & SET_TARGET_FREQ_MASK_BIT) {
|
|
training_stage = SET_TARGET_FREQ;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("SET_TARGET_FREQ_MASK_BIT %d\n",
|
|
freq_val[tm->
|
|
interface_params[first_active_if].
|
|
memory_freq]));
|
|
ret = ddr3_tip_freq_set(dev_num, ACCESS_TYPE_MULTICAST,
|
|
PARAM_NOT_CARE,
|
|
tm->interface_params[first_active_if].
|
|
memory_freq);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_freq_set failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
if (mask_tune_func & WRITE_LEVELING_TF_MASK_BIT) {
|
|
training_stage = WRITE_LEVELING_TF;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("WRITE_LEVELING_TF_MASK_BIT\n"));
|
|
ret = ddr3_tip_dynamic_write_leveling(dev_num);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_dynamic_write_leveling TF failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
if (mask_tune_func & LOAD_PATTERN_HIGH_MASK_BIT) {
|
|
training_stage = LOAD_PATTERN_HIGH;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO, ("LOAD_PATTERN_HIGH\n"));
|
|
ret = ddr3_tip_load_all_pattern_to_mem(dev_num);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_load_all_pattern_to_mem failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
if (mask_tune_func & READ_LEVELING_TF_MASK_BIT) {
|
|
training_stage = READ_LEVELING_TF;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("READ_LEVELING_TF_MASK_BIT\n"));
|
|
ret = ddr3_tip_dynamic_read_leveling(dev_num, tm->
|
|
interface_params[first_active_if].
|
|
memory_freq);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_dynamic_read_leveling TF failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
if (mask_tune_func & DM_PBS_TX_MASK_BIT) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO, ("DM_PBS_TX_MASK_BIT\n"));
|
|
}
|
|
|
|
for (effective_cs = 0; effective_cs < max_cs; effective_cs++) {
|
|
if (mask_tune_func & VREF_CALIBRATION_MASK_BIT) {
|
|
training_stage = VREF_CALIBRATION;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO, ("VREF\n"));
|
|
ret = ddr3_tip_vref(dev_num);
|
|
if (is_reg_dump != 0) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("VREF Dump\n"));
|
|
ddr3_tip_reg_dump(dev_num);
|
|
}
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_vref failure\n"));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
}
|
|
/* Set to 0 after each loop to avoid illegal value may be used */
|
|
effective_cs = 0;
|
|
|
|
for (effective_cs = 0; effective_cs < max_cs; effective_cs++) {
|
|
if (mask_tune_func & CENTRALIZATION_RX_MASK_BIT) {
|
|
training_stage = CENTRALIZATION_RX;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("CENTRALIZATION_RX_MASK_BIT CS #%d\n",
|
|
effective_cs));
|
|
ret = ddr3_tip_centralization_rx(dev_num);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_centralization_rx failure CS #%d\n",
|
|
effective_cs));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
}
|
|
/* Set to 0 after each loop to avoid illegal value may be used */
|
|
effective_cs = 0;
|
|
|
|
for (effective_cs = 0; effective_cs < max_cs; effective_cs++) {
|
|
if (mask_tune_func & WRITE_LEVELING_SUPP_TF_MASK_BIT) {
|
|
training_stage = WRITE_LEVELING_SUPP_TF;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("WRITE_LEVELING_SUPP_TF_MASK_BIT CS #%d\n",
|
|
effective_cs));
|
|
ret = ddr3_tip_dynamic_write_leveling_supp(dev_num);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_dynamic_write_leveling_supp TF failure CS #%d\n",
|
|
effective_cs));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
}
|
|
/* Set to 0 after each loop to avoid illegal value may be used */
|
|
effective_cs = 0;
|
|
|
|
for (effective_cs = 0; effective_cs < max_cs; effective_cs++) {
|
|
if (mask_tune_func & CENTRALIZATION_TX_MASK_BIT) {
|
|
training_stage = CENTRALIZATION_TX;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("CENTRALIZATION_TX_MASK_BIT CS #%d\n",
|
|
effective_cs));
|
|
ret = ddr3_tip_centralization_tx(dev_num);
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
if (ret != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_centralization_tx failure CS #%d\n",
|
|
effective_cs));
|
|
if (debug_mode == 0)
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
}
|
|
/* Set to 0 after each loop to avoid illegal value may be used */
|
|
effective_cs = 0;
|
|
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO, ("restore registers to default\n"));
|
|
/* restore register values */
|
|
CHECK_STATUS(ddr3_tip_restore_dunit_regs(dev_num));
|
|
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* DDR3 Dynamic training flow
|
|
*/
|
|
static int ddr3_tip_ddr3_auto_tune(u32 dev_num)
|
|
{
|
|
u32 if_id, stage, ret;
|
|
int is_if_fail = 0, is_auto_tune_fail = 0;
|
|
|
|
training_stage = INIT_CONTROLLER;
|
|
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
for (stage = 0; stage < MAX_STAGE_LIMIT; stage++)
|
|
training_result[stage][if_id] = NO_TEST_DONE;
|
|
}
|
|
|
|
ret = ddr3_tip_ddr3_training_main_flow(dev_num);
|
|
|
|
/* activate XSB test */
|
|
if (xsb_validate_type != 0) {
|
|
run_xsb_test(dev_num, xsb_validation_base_address, 1, 1,
|
|
0x1024);
|
|
}
|
|
|
|
if (is_reg_dump != 0)
|
|
ddr3_tip_reg_dump(dev_num);
|
|
|
|
/* print log */
|
|
CHECK_STATUS(ddr3_tip_print_log(dev_num, window_mem_addr));
|
|
|
|
if (ret != MV_OK) {
|
|
CHECK_STATUS(ddr3_tip_print_stability_log(dev_num));
|
|
}
|
|
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
is_if_fail = 0;
|
|
for (stage = 0; stage < MAX_STAGE_LIMIT; stage++) {
|
|
if (training_result[stage][if_id] == TEST_FAILED)
|
|
is_if_fail = 1;
|
|
}
|
|
if (is_if_fail == 1) {
|
|
is_auto_tune_fail = 1;
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
|
|
("Auto Tune failed for IF %d\n",
|
|
if_id));
|
|
}
|
|
}
|
|
|
|
if ((ret == MV_FAIL) || (is_auto_tune_fail == 1))
|
|
return MV_FAIL;
|
|
else
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Enable init sequence
|
|
*/
|
|
int ddr3_tip_enable_init_sequence(u32 dev_num)
|
|
{
|
|
int is_fail = 0;
|
|
u32 if_id = 0, mem_mask = 0, bus_index = 0;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
/* Enable init sequence */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, ACCESS_TYPE_MULTICAST, 0,
|
|
SDRAM_INIT_CONTROL_REG, 0x1, 0x1));
|
|
|
|
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, if_id);
|
|
|
|
if (ddr3_tip_if_polling
|
|
(dev_num, ACCESS_TYPE_UNICAST, if_id, 0, 0x1,
|
|
SDRAM_INIT_CONTROL_REG,
|
|
MAX_POLLING_ITERATIONS) != MV_OK) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("polling failed IF %d\n",
|
|
if_id));
|
|
is_fail = 1;
|
|
continue;
|
|
}
|
|
|
|
mem_mask = 0;
|
|
for (bus_index = 0; bus_index < GET_TOPOLOGY_NUM_OF_BUSES();
|
|
bus_index++) {
|
|
VALIDATE_ACTIVE(tm->bus_act_mask, bus_index);
|
|
mem_mask |=
|
|
tm->interface_params[if_id].
|
|
as_bus_params[bus_index].mirror_enable_bitmask;
|
|
}
|
|
|
|
if (mem_mask != 0) {
|
|
/* Disable Multi CS */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num, ACCESS_TYPE_MULTICAST,
|
|
if_id, CS_ENABLE_REG, 1 << 3,
|
|
1 << 3));
|
|
}
|
|
}
|
|
|
|
return (is_fail == 0) ? MV_OK : MV_FAIL;
|
|
}
|
|
|
|
int ddr3_tip_register_dq_table(u32 dev_num, u32 *table)
|
|
{
|
|
dq_map_table = table;
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Check if pup search is locked
|
|
*/
|
|
int ddr3_tip_is_pup_lock(u32 *pup_buf, enum hws_training_result read_mode)
|
|
{
|
|
u32 bit_start = 0, bit_end = 0, bit_id;
|
|
|
|
if (read_mode == RESULT_PER_BIT) {
|
|
bit_start = 0;
|
|
bit_end = BUS_WIDTH_IN_BITS - 1;
|
|
} else {
|
|
bit_start = 0;
|
|
bit_end = 0;
|
|
}
|
|
|
|
for (bit_id = bit_start; bit_id <= bit_end; bit_id++) {
|
|
if (GET_LOCK_RESULT(pup_buf[bit_id]) == 0)
|
|
return 0;
|
|
}
|
|
|
|
return 1;
|
|
}
|
|
|
|
/*
|
|
* Get minimum buffer value
|
|
*/
|
|
u8 ddr3_tip_get_buf_min(u8 *buf_ptr)
|
|
{
|
|
u8 min_val = 0xff;
|
|
u8 cnt = 0;
|
|
|
|
for (cnt = 0; cnt < BUS_WIDTH_IN_BITS; cnt++) {
|
|
if (buf_ptr[cnt] < min_val)
|
|
min_val = buf_ptr[cnt];
|
|
}
|
|
|
|
return min_val;
|
|
}
|
|
|
|
/*
|
|
* Get maximum buffer value
|
|
*/
|
|
u8 ddr3_tip_get_buf_max(u8 *buf_ptr)
|
|
{
|
|
u8 max_val = 0;
|
|
u8 cnt = 0;
|
|
|
|
for (cnt = 0; cnt < BUS_WIDTH_IN_BITS; cnt++) {
|
|
if (buf_ptr[cnt] > max_val)
|
|
max_val = buf_ptr[cnt];
|
|
}
|
|
|
|
return max_val;
|
|
}
|
|
|
|
/*
|
|
* The following functions return memory parameters:
|
|
* bus and device width, device size
|
|
*/
|
|
|
|
u32 hws_ddr3_get_bus_width(void)
|
|
{
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
return (DDR3_IS_16BIT_DRAM_MODE(tm->bus_act_mask) ==
|
|
1) ? 16 : 32;
|
|
}
|
|
|
|
u32 hws_ddr3_get_device_width(u32 if_id)
|
|
{
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
return (tm->interface_params[if_id].bus_width ==
|
|
BUS_WIDTH_8) ? 8 : 16;
|
|
}
|
|
|
|
u32 hws_ddr3_get_device_size(u32 if_id)
|
|
{
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
if (tm->interface_params[if_id].memory_size >=
|
|
MEM_SIZE_LAST) {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("Error: Wrong device size of Cs: %d",
|
|
tm->interface_params[if_id].memory_size));
|
|
return 0;
|
|
} else {
|
|
return 1 << tm->interface_params[if_id].memory_size;
|
|
}
|
|
}
|
|
|
|
int hws_ddr3_calc_mem_cs_size(u32 if_id, u32 cs, u32 *cs_size)
|
|
{
|
|
u32 cs_mem_size, dev_size;
|
|
|
|
dev_size = hws_ddr3_get_device_size(if_id);
|
|
if (dev_size != 0) {
|
|
cs_mem_size = ((hws_ddr3_get_bus_width() /
|
|
hws_ddr3_get_device_width(if_id)) * dev_size);
|
|
|
|
/* the calculated result in Gbytex16 to avoid float using */
|
|
|
|
if (cs_mem_size == 2) {
|
|
*cs_size = _128M;
|
|
} else if (cs_mem_size == 4) {
|
|
*cs_size = _256M;
|
|
} else if (cs_mem_size == 8) {
|
|
*cs_size = _512M;
|
|
} else if (cs_mem_size == 16) {
|
|
*cs_size = _1G;
|
|
} else if (cs_mem_size == 32) {
|
|
*cs_size = _2G;
|
|
} else {
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("Error: Wrong Memory size of Cs: %d", cs));
|
|
return MV_FAIL;
|
|
}
|
|
return MV_OK;
|
|
} else {
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
int hws_ddr3_cs_base_adr_calc(u32 if_id, u32 cs, u32 *cs_base_addr)
|
|
{
|
|
u32 cs_mem_size = 0;
|
|
#ifdef DEVICE_MAX_DRAM_ADDRESS_SIZE
|
|
u32 physical_mem_size;
|
|
u32 max_mem_size = DEVICE_MAX_DRAM_ADDRESS_SIZE;
|
|
#endif
|
|
|
|
if (hws_ddr3_calc_mem_cs_size(if_id, cs, &cs_mem_size) != MV_OK)
|
|
return MV_FAIL;
|
|
|
|
#ifdef DEVICE_MAX_DRAM_ADDRESS_SIZE
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
/*
|
|
* if number of address pins doesn't allow to use max mem size that
|
|
* is defined in topology mem size is defined by
|
|
* DEVICE_MAX_DRAM_ADDRESS_SIZE
|
|
*/
|
|
physical_mem_size =
|
|
mv_hwsmem_size[tm->interface_params[0].memory_size];
|
|
|
|
if (hws_ddr3_get_device_width(cs) == 16) {
|
|
/*
|
|
* 16bit mem device can be twice more - no need in less
|
|
* significant pin
|
|
*/
|
|
max_mem_size = DEVICE_MAX_DRAM_ADDRESS_SIZE * 2;
|
|
}
|
|
|
|
if (physical_mem_size > max_mem_size) {
|
|
cs_mem_size = max_mem_size *
|
|
(hws_ddr3_get_bus_width() /
|
|
hws_ddr3_get_device_width(if_id));
|
|
DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
|
|
("Updated Physical Mem size is from 0x%x to %x\n",
|
|
physical_mem_size,
|
|
DEVICE_MAX_DRAM_ADDRESS_SIZE));
|
|
}
|
|
#endif
|
|
|
|
/* calculate CS base addr */
|
|
*cs_base_addr = ((cs_mem_size) * cs) & 0xffff0000;
|
|
|
|
return MV_OK;
|
|
}
|
|
|