upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
351 lines
13 KiB
351 lines
13 KiB
/*
|
|
* (C) Copyright 2001-2003
|
|
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
|
|
#define CONFIG_ASH405 1 /* ...on a ASH405 board */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
|
|
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
|
|
|
|
#define CONFIG_SYS_CLK_FREQ 33333300 /* external frequency to pll */
|
|
|
|
#define CONFIG_BAUDRATE 9600
|
|
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
#undef CONFIG_BOOTCOMMAND
|
|
|
|
#define CONFIG_PREBOOT /* enable preboot variable */
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
#undef CONFIG_HAS_ETH1
|
|
|
|
#define CONFIG_PPC4xx_EMAC
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_PHY_ADDR 0 /* PHY address */
|
|
#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
|
|
#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
|
|
|
|
#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_IRQ
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_NAND
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_EEPROM
|
|
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
|
|
#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
|
|
|
|
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
|
|
#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
|
|
|
|
#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
|
|
#define CONFIG_SYS_NS16550
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
|
|
|
|
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
|
|
#define CONFIG_SYS_BASE_BAUD 691200
|
|
|
|
/* The following table includes the supported baudrates */
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
|
|
57600, 115200, 230400, 460800, 921600 }
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
|
|
|
|
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
|
|
|
|
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
|
|
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* NAND-FLASH stuff
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
|
|
#define NAND_BIG_DELAY_US 25
|
|
|
|
#define CONFIG_SYS_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
|
|
#define CONFIG_SYS_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
|
|
#define CONFIG_SYS_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
|
|
#define CONFIG_SYS_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
|
|
|
|
#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
|
|
#define CONFIG_SYS_NAND_QUIET 1
|
|
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
|
|
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCI stuff
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
|
|
#define PCI_HOST_FORCE 1 /* configure as pci host */
|
|
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
|
|
|
|
#define CONFIG_PCI /* include pci support */
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
|
|
#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
|
|
#undef CONFIG_PCI_PNP /* do pci plug-and-play */
|
|
/* resource configuration */
|
|
|
|
#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
|
|
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
|
|
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
|
|
#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
|
|
#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
|
|
#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
|
|
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
|
|
#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
|
|
#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
|
|
#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE 0xFFFC0000
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
|
|
#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
|
|
#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
|
|
/*
|
|
* The following defines are added for buggy IOP480 byte interface.
|
|
* All other boards should use the standard values (CPCI405 etc.)
|
|
*/
|
|
#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
|
|
#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
|
|
#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
|
|
|
|
#if 0 /* test-only */
|
|
#define CONFIG_SYS_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
|
|
#define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Environment Variable setup
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
|
|
#define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
|
|
#define CONFIG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
|
|
/* total size of a CAT24WC16 is 2048 bytes */
|
|
|
|
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
|
|
#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* I2C EEPROM (CAT24WC16) for environment
|
|
*/
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_PPC4XX
|
|
#define CONFIG_SYS_I2C_PPC4XX_CH0
|
|
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
|
|
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
|
|
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
|
|
/* mask of address bits that overflow into the "EEPROM chip address" */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
|
|
/* 16 byte page write mode using*/
|
|
/* last 4 bits of the address */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* BR0/1 and OR0/1 (FLASH)
|
|
*/
|
|
|
|
#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* External Bus Controller (EBC) Setup
|
|
*/
|
|
|
|
/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
|
|
#define CONFIG_SYS_EBC_PB0AP 0x92015480
|
|
/*#define CONFIG_SYS_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
|
|
#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
|
|
|
|
/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
|
|
#define CONFIG_SYS_EBC_PB1AP 0x92015480
|
|
#define CONFIG_SYS_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
|
|
|
|
/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
|
|
#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
|
|
#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
|
|
|
|
/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
|
|
#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
|
|
#define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
|
|
|
|
#define CAN_BA 0xF0000000 /* CAN Base Address */
|
|
#define DUART0_BA 0xF0000400 /* DUART Base Address */
|
|
#define DUART1_BA 0xF0000408 /* DUART Base Address */
|
|
#define DUART2_BA 0xF0000410 /* DUART Base Address */
|
|
#define DUART3_BA 0xF0000418 /* DUART Base Address */
|
|
#define RTC_BA 0xF0000500 /* RTC Base Address */
|
|
#define CONFIG_SYS_NAND_BASE 0xF4000000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FPGA stuff
|
|
*/
|
|
#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
|
|
#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
|
|
|
|
/* FPGA program pin configuration */
|
|
#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
|
|
#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
|
|
#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
|
|
#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
|
|
#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in data cache)
|
|
*/
|
|
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
|
|
#define CONFIG_SYS_TEMP_STACK_OCM 1
|
|
|
|
/* On Chip Memory location */
|
|
#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
|
|
#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for GPIO setup (PPC405EP specific)
|
|
*
|
|
* GPIO0[0] - External Bus Controller BLAST output
|
|
* GPIO0[1-9] - Instruction trace outputs -> GPIO
|
|
* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
|
|
* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
|
|
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
|
|
* GPIO0[24-27] - UART0 control signal inputs/outputs
|
|
* GPIO0[28-29] - UART1 data signal input/output
|
|
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
|
|
*/
|
|
#define CONFIG_SYS_GPIO0_OSRL 0x40000550
|
|
#define CONFIG_SYS_GPIO0_OSRH 0x00000110
|
|
#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
|
|
#define CONFIG_SYS_GPIO0_ISR1H 0x15555445
|
|
#define CONFIG_SYS_GPIO0_TSRL 0x00000000
|
|
#define CONFIG_SYS_GPIO0_TSRH 0x00000000
|
|
#define CONFIG_SYS_GPIO0_TCR 0xF7FE0014
|
|
|
|
#define CONFIG_SYS_DUART_RST (0x80000000 >> 14)
|
|
|
|
/*
|
|
* Default speed selection (cpu_plb_opb_ebc) in mhz.
|
|
* This value will be set if iic boot eprom is disabled.
|
|
*/
|
|
#if 0
|
|
#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
|
|
#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
|
|
#endif
|
|
#if 1
|
|
#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
|
|
#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
|
|
#endif
|
|
#if 0
|
|
#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
|
|
#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
|
|
#endif
|
|
|
|
#endif /* __CONFIG_H */
|
|
|