upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
621 lines
26 KiB
621 lines
26 KiB
/*
|
|
* (C) Copyright 2007-2008
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
|
|
/************************************************************************
|
|
* lwmon5.h - configuration for lwmon5 board
|
|
***********************************************************************/
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* High Level Configuration Options
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_LWMON5 1 /* Board is lwmon5 */
|
|
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
|
|
#define CONFIG_440 1 /* ... PPC440 family */
|
|
#define CONFIG_4xx 1 /* ... PPC4xx family */
|
|
#define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
|
|
#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */
|
|
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
|
|
#define CONFIG_BOARD_RESET 1 /* Call board_reset */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Base addresses -- Note these are effective addresses where the
|
|
* actual resources get mapped (not physical addresses)
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
|
|
|
|
#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
|
|
#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */
|
|
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
|
|
#define CONFIG_SYS_LIME_BASE_0 0xc0000000
|
|
#define CONFIG_SYS_LIME_BASE_1 0xc1000000
|
|
#define CONFIG_SYS_LIME_BASE_2 0xc2000000
|
|
#define CONFIG_SYS_LIME_BASE_3 0xc3000000
|
|
#define CONFIG_SYS_FPGA_BASE_0 0xc4000000
|
|
#define CONFIG_SYS_FPGA_BASE_1 0xc4200000
|
|
#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
|
|
#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
|
|
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
|
|
#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
|
|
#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
|
|
#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
|
|
|
|
/* Don't change either of these */
|
|
#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
|
|
|
|
#define CONFIG_SYS_USB2D0_BASE 0xe0000100
|
|
#define CONFIG_SYS_USB_DEVICE 0xe0000000
|
|
#define CONFIG_SYS_USB_HOST 0xe0000400
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Initial RAM & stack pointer
|
|
*----------------------------------------------------------------------*/
|
|
/*
|
|
* On LWMON5 we use D-cache as init-ram and stack pointer. We also move
|
|
* the POST_WORD from OCM to a 440EPx register that preserves it's
|
|
* content during reset (GPT0_COMP6). This way we reserve the OCM (16k)
|
|
* for logbuffer only. (GPT0_COMP1-COMP5 are reserved for logbuffer header.)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */
|
|
#define CONFIG_SYS_INIT_RAM_END (4 << 10)
|
|
#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data*/
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
#define CONFIG_SYS_POST_ALT_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
|
|
/* unused GPT0 COMP reg */
|
|
#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
|
|
/* 440EPx errata CHIP 11 */
|
|
#define CONFIG_SYS_OCM_SIZE (16 << 10)
|
|
|
|
/* Additional registers for watchdog timer post test */
|
|
|
|
#define CONFIG_SYS_WATCHDOG_TIME_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK2)
|
|
#define CONFIG_SYS_WATCHDOG_FLAGS_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK1)
|
|
#define CONFIG_SYS_DSPIC_TEST_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR
|
|
#define CONFIG_SYS_OCM_STATUS_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR
|
|
#define CONFIG_SYS_WATCHDOG_MAGIC 0x12480000
|
|
#define CONFIG_SYS_WATCHDOG_MAGIC_MASK 0xFFFF0000
|
|
#define CONFIG_SYS_DSPIC_TEST_MASK 0x00000001
|
|
#define CONFIG_SYS_OCM_STATUS_OK 0x00009A00
|
|
#define CONFIG_SYS_OCM_STATUS_FAIL 0x0000A300
|
|
#define CONFIG_SYS_OCM_STATUS_MASK 0x0000FF00
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Serial Port
|
|
*----------------------------------------------------------------------*/
|
|
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external clock provided */
|
|
#define CONFIG_BAUDRATE 115200
|
|
#define CONFIG_SERIAL_MULTI 1
|
|
/* define this if you want console on UART1 */
|
|
#define CONFIG_UART1_CONSOLE 1 /* use UART1 as console */
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Environment
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH related
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
|
|
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
|
|
|
|
#define CONFIG_SYS_FLASH0 0xFC000000
|
|
#define CONFIG_SYS_FLASH1 0xF8000000
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 }
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
|
|
#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
|
|
#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
|
|
|
|
#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
|
|
#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* DDR SDRAM
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */
|
|
#define CONFIG_SYS_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */
|
|
#define CONFIG_DDR_DATA_EYE 1 /* use DDR2 optimization */
|
|
#define CONFIG_DDR_ECC 1 /* enable ECC */
|
|
#define CONFIG_SYS_POST_ECC_ON CONFIG_SYS_POST_ECC
|
|
|
|
/* POST support */
|
|
#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
|
|
CONFIG_SYS_POST_CPU | \
|
|
CONFIG_SYS_POST_ECC_ON | \
|
|
CONFIG_SYS_POST_ETHER | \
|
|
CONFIG_SYS_POST_FPU | \
|
|
CONFIG_SYS_POST_I2C | \
|
|
CONFIG_SYS_POST_MEMORY | \
|
|
CONFIG_SYS_POST_OCM | \
|
|
CONFIG_SYS_POST_RTC | \
|
|
CONFIG_SYS_POST_SPR | \
|
|
CONFIG_SYS_POST_UART | \
|
|
CONFIG_SYS_POST_SYSMON | \
|
|
CONFIG_SYS_POST_WATCHDOG | \
|
|
CONFIG_SYS_POST_DSP | \
|
|
CONFIG_SYS_POST_BSPEC1 | \
|
|
CONFIG_SYS_POST_BSPEC2 | \
|
|
CONFIG_SYS_POST_BSPEC3 | \
|
|
CONFIG_SYS_POST_BSPEC4 | \
|
|
CONFIG_SYS_POST_BSPEC5)
|
|
|
|
#define CONFIG_POST_WATCHDOG {\
|
|
"Watchdog timer test", \
|
|
"watchdog", \
|
|
"This test checks the watchdog timer.", \
|
|
POST_RAM | POST_POWERON | POST_SLOWTEST | POST_MANUAL | POST_REBOOT, \
|
|
&lwmon5_watchdog_post_test, \
|
|
NULL, \
|
|
NULL, \
|
|
CONFIG_SYS_POST_WATCHDOG \
|
|
}
|
|
|
|
#define CONFIG_POST_BSPEC1 {\
|
|
"dsPIC init test", \
|
|
"dspic_init", \
|
|
"This test returns result of dsPIC READY test run earlier.", \
|
|
POST_RAM | POST_ALWAYS, \
|
|
&dspic_init_post_test, \
|
|
NULL, \
|
|
NULL, \
|
|
CONFIG_SYS_POST_BSPEC1 \
|
|
}
|
|
|
|
#define CONFIG_POST_BSPEC2 {\
|
|
"dsPIC test", \
|
|
"dspic", \
|
|
"This test gets result of dsPIC POST and dsPIC version.", \
|
|
POST_RAM | POST_ALWAYS, \
|
|
&dspic_post_test, \
|
|
NULL, \
|
|
NULL, \
|
|
CONFIG_SYS_POST_BSPEC2 \
|
|
}
|
|
|
|
#define CONFIG_POST_BSPEC3 {\
|
|
"FPGA test", \
|
|
"fpga", \
|
|
"This test checks FPGA registers and memory.", \
|
|
POST_RAM | POST_ALWAYS, \
|
|
&fpga_post_test, \
|
|
NULL, \
|
|
NULL, \
|
|
CONFIG_SYS_POST_BSPEC3 \
|
|
}
|
|
|
|
#define CONFIG_POST_BSPEC4 {\
|
|
"GDC test", \
|
|
"gdc", \
|
|
"This test checks GDC registers and memory.", \
|
|
POST_RAM | POST_ALWAYS, \
|
|
&gdc_post_test, \
|
|
NULL, \
|
|
NULL, \
|
|
CONFIG_SYS_POST_BSPEC4 \
|
|
}
|
|
|
|
#define CONFIG_POST_BSPEC5 {\
|
|
"SYSMON1 test", \
|
|
"sysmon1", \
|
|
"This test checks GPIO_62_EPX pin indicating power failure.", \
|
|
POST_RAM | POST_MANUAL | POST_NORMAL | POST_SLOWTEST, \
|
|
&sysmon1_post_test, \
|
|
NULL, \
|
|
NULL, \
|
|
CONFIG_SYS_POST_BSPEC5 \
|
|
}
|
|
|
|
#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
|
|
#define CONFIG_LOGBUFFER
|
|
/* Reserve GPT0_COMP1-COMP5 for logbuffer header */
|
|
#define CONFIG_ALT_LH_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP1)
|
|
#define CONFIG_ALT_LB_ADDR (CONFIG_SYS_OCM_BASE)
|
|
#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* I2C
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
|
|
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
|
|
#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F
|
|
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 /* EEPROM AT24C128 */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel AT24C128 has */
|
|
/* 64 byte page write mode using*/
|
|
/* last 6 bits of the address */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
|
|
|
|
#define CONFIG_RTC_PCF8563 1 /* enable Philips PCF8563 RTC */
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */
|
|
#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */
|
|
#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */
|
|
|
|
#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */
|
|
#if 0
|
|
#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */
|
|
#define CONFIG_AUTOBOOT_PROMPT \
|
|
"\nEnter password - autoboot in %d sec...\n", bootdelay
|
|
#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */
|
|
#endif
|
|
|
|
#define CONFIG_PREBOOT "setenv bootdelay 15"
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"hostname=lwmon5\0" \
|
|
"netdev=eth0\0" \
|
|
"unlock=yes\0" \
|
|
"logversion=2\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"addip=setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
|
":${hostname}:${netdev}:off panic=1\0" \
|
|
"addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\
|
|
"addmisc=setenv bootargs ${bootargs} rtc-pcf8563.probe=0,0x51\0"\
|
|
"flash_nfs=run nfsargs addip addtty addmisc;" \
|
|
"bootm ${kernel_addr}\0" \
|
|
"flash_self=run ramargs addip addtty addmisc;" \
|
|
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
|
|
"net_nfs=tftp 200000 ${bootfile};" \
|
|
"run nfsargs addip addtty addmisc;bootm\0" \
|
|
"rootpath=/opt/eldk/ppc_4xxFP\0" \
|
|
"bootfile=/tftpboot/lwmon5/uImage\0" \
|
|
"kernel_addr=FC000000\0" \
|
|
"ramdisk_addr=FC180000\0" \
|
|
"load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \
|
|
"update=protect off FFF80000 FFFFFFFF;era FFF80000 FFFFFFFF;" \
|
|
"cp.b 200000 FFF80000 80000\0" \
|
|
"upd=run load update\0" \
|
|
"lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;" \
|
|
"autoscr 200000\0" \
|
|
""
|
|
#define CONFIG_BOOTCOMMAND "run flash_self"
|
|
|
|
#if 0
|
|
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
|
|
#else
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
#endif
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
#define CONFIG_IBM_EMAC4_V4 1
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_PHY_ADDR 3 /* PHY address, See schematics */
|
|
|
|
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
|
|
#define CONFIG_PHY_RESET_DELAY 300
|
|
|
|
#define CONFIG_HAS_ETH0
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
|
|
|
|
#define CONFIG_NET_MULTI 1
|
|
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
|
|
#define CONFIG_PHY1_ADDR 1
|
|
|
|
/* Video console */
|
|
#define CONFIG_VIDEO
|
|
#define CONFIG_VIDEO_MB862xx
|
|
#define CONFIG_CFB_CONSOLE
|
|
#define CONFIG_VIDEO_LOGO
|
|
#define CONFIG_CONSOLE_EXTRA_INFO
|
|
#define VIDEO_FB_16BPP_PIXEL_SWAP
|
|
|
|
#define CONFIG_VGA_AS_SINGLE_DEVICE
|
|
#define CONFIG_VIDEO_SW_CURSOR
|
|
#define CONFIG_SPLASH_SCREEN
|
|
|
|
/* USB */
|
|
#ifdef CONFIG_440EPX
|
|
#define CONFIG_USB_OHCI
|
|
#define CONFIG_USB_STORAGE
|
|
|
|
/* Comment this out to enable USB 1.1 device */
|
|
#define USB_2_0_DEVICE
|
|
|
|
#endif /* CONFIG_440EPX */
|
|
|
|
/* Partitions */
|
|
#define CONFIG_MAC_PARTITION
|
|
#define CONFIG_DOS_PARTITION
|
|
#define CONFIG_ISO_PARTITION
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_ASKENV
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_DIAG
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_FAT
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_IRQ
|
|
#define CONFIG_CMD_LOG
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_NET
|
|
#define CONFIG_CMD_NFS
|
|
#define CONFIG_CMD_PCI
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_REGINFO
|
|
#define CONFIG_CMD_SDRAM
|
|
|
|
#ifdef CONFIG_VIDEO
|
|
#define CONFIG_CMD_BMP
|
|
#endif
|
|
|
|
#ifdef CONFIG_440EPX
|
|
#define CONFIG_CMD_USB
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Miscellaneous configurable options
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SUPPORT_VFAT
|
|
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
|
|
|
|
#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
|
|
#ifdef CONFIG_SYS_HUSH_PARSER
|
|
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
|
|
#endif
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
|
|
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
|
|
#define CONFIG_LOOPW 1 /* enable loopw command */
|
|
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
|
|
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCI stuff
|
|
*----------------------------------------------------------------------*/
|
|
/* General PCI */
|
|
#define CONFIG_PCI /* include pci support */
|
|
#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
|
|
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/
|
|
|
|
/* Board-specific PCI */
|
|
#define CONFIG_SYS_PCI_TARGET_INIT
|
|
#define CONFIG_SYS_PCI_MASTER_INIT
|
|
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
|
|
#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
|
|
|
|
#define CONFIG_HW_WATCHDOG 1 /* Use external HW-Watchdog */
|
|
#define CONFIG_WD_PERIOD 40000 /* in usec */
|
|
#define CONFIG_WD_MAX_RATE 66600 /* in ticks */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* External Bus Controller (EBC) Setup
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
|
|
|
|
/* Memory Bank 0 (NOR-FLASH) initialization */
|
|
#define CONFIG_SYS_EBC_PB0AP 0x03050200
|
|
#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xfc000)
|
|
|
|
/* Memory Bank 1 (Lime) initialization */
|
|
#define CONFIG_SYS_EBC_PB1AP 0x01004380
|
|
#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_LIME_BASE_0 | 0xdc000)
|
|
|
|
/* Memory Bank 2 (FPGA) initialization */
|
|
#define CONFIG_SYS_EBC_PB2AP 0x01004400
|
|
#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA_BASE_0 | 0x1c000)
|
|
|
|
/* Memory Bank 3 (FPGA2) initialization */
|
|
#define CONFIG_SYS_EBC_PB3AP 0x01004400
|
|
#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_FPGA_BASE_1 | 0x1c000)
|
|
|
|
#define CONFIG_SYS_EBC_CFG 0xb8400000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Graphics (Fujitsu Lime)
|
|
*----------------------------------------------------------------------*/
|
|
/* SDRAM Clock frequency adjustment register */
|
|
#define CONFIG_SYS_LIME_SDRAM_CLOCK 0xC1FC0038
|
|
/* Lime Clock frequency is to set 100MHz */
|
|
#define CONFIG_SYS_LIME_CLOCK_100MHZ 0x00000
|
|
#if 0
|
|
/* Lime Clock frequency for 133MHz */
|
|
#define CONFIG_SYS_LIME_CLOCK_133MHZ 0x10000
|
|
#endif
|
|
|
|
/* SDRAM Parameter register */
|
|
#define CONFIG_SYS_LIME_MMR 0xC1FCFFFC
|
|
/* SDRAM parameter value; was 0x414FB7F2, caused several vertical bars
|
|
and pixel flare on display when 133MHz was configured. According to
|
|
SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed Grade */
|
|
#ifdef CONFIG_SYS_LIME_CLOCK_133MHZ
|
|
#define CONFIG_SYS_LIME_MMR_VALUE 0x414FB7F3
|
|
#else
|
|
#define CONFIG_SYS_LIME_MMR_VALUE 0x414FB7F2
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* GPIO Setup
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_GPIO_PHY1_RST 12
|
|
#define CONFIG_SYS_GPIO_FLASH_WP 14
|
|
#define CONFIG_SYS_GPIO_PHY0_RST 22
|
|
#define CONFIG_SYS_GPIO_DSPIC_READY 51
|
|
#define CONFIG_SYS_GPIO_EEPROM_EXT_WP 55
|
|
#define CONFIG_SYS_GPIO_HIGHSIDE 56
|
|
#define CONFIG_SYS_GPIO_EEPROM_INT_WP 57
|
|
#define CONFIG_SYS_GPIO_BOARD_RESET 58
|
|
#define CONFIG_SYS_GPIO_LIME_S 59
|
|
#define CONFIG_SYS_GPIO_LIME_RST 60
|
|
#define CONFIG_SYS_GPIO_SYSMON_STATUS 62
|
|
#define CONFIG_SYS_GPIO_WATCHDOG 63
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PPC440 GPIO Configuration
|
|
*/
|
|
#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
|
|
{ \
|
|
/* GPIO Core 0 */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \
|
|
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO13 */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14 */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO15 */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 GMCTxD(4) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMCTxD(5) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMCTxD(6) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 GMCTxD(7) */ \
|
|
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \
|
|
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 SCPD0 */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 GMCTxD(2) */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 GMCTxD(3) */ \
|
|
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \
|
|
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 USB2D_TXVALID */ \
|
|
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \
|
|
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \
|
|
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \
|
|
}, \
|
|
{ \
|
|
/* GPIO Core 1 */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_0}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0) UART3_SIN*/ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO49 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO55 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO57 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
|
|
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
|
|
} \
|
|
}
|
|
|
|
/*
|
|
* Internal Definitions
|
|
*
|
|
* Boot Flags
|
|
*/
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
|
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
|
|
#endif
|
|
#endif /* __CONFIG_H */
|
|
|