upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
323 lines
9.3 KiB
323 lines
9.3 KiB
/*
|
|
* (C) Copyright 2008
|
|
* Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
|
|
*
|
|
* Based on board/amcc/yosemite/yosemite.c
|
|
* (C) Copyright 2006-2007
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <ppc4xx.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/io.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/* info for FLASH chips */
|
|
extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
register uint reg;
|
|
|
|
/*
|
|
* Setup the external bus controller/chip selects
|
|
*/
|
|
mfebc(xbcfg, reg);
|
|
mtebc(xbcfg, reg | 0x04000000); /* Set ATC */
|
|
|
|
/*
|
|
* Setup the GPIO pins
|
|
*/
|
|
|
|
/* setup Address lines for flash size 64Meg. */
|
|
out32(GPIO0_OSRL, in32(GPIO0_OSRL) | 0x54000000);
|
|
out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x54000000);
|
|
out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x54000000);
|
|
|
|
/* setup emac */
|
|
out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xC080);
|
|
out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x40);
|
|
out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x55);
|
|
out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0x50004000);
|
|
out32(GPIO0_ISR1H, in32(GPIO0_ISR1H) | 0x00440000);
|
|
|
|
/* UART0 and UART1*/
|
|
out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x16000000);
|
|
out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x02180000);
|
|
out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00400000);
|
|
out32(GPIO1_ISR2L, in32(GPIO1_ISR2L) | 0x04010000);
|
|
|
|
/* disable boot-eeprom WP */
|
|
out32(GPIO0_OSRL, in32(GPIO0_OSRL) & ~0x00C00000);
|
|
out32(GPIO0_TSRL, in32(GPIO0_TSRL) & ~0x00C00000);
|
|
out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) & ~0x00C00000);
|
|
out32(GPIO0_TCR, in32(GPIO0_TCR) | 0x08000000);
|
|
out32(GPIO0_OR, in32(GPIO0_OR) & ~0x08000000);
|
|
|
|
/* external interrupts IRQ0...3 */
|
|
out32(GPIO1_TCR, in32(GPIO1_TCR) & ~0x00f00000);
|
|
out32(GPIO1_TSRL, in32(GPIO1_TSRL) & ~0x00005500);
|
|
out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00005500);
|
|
|
|
|
|
/*
|
|
* Setup the interrupt controller polarities, triggers, etc.
|
|
*/
|
|
mtdcr(uic0sr, 0xffffffff); /* clear all */
|
|
mtdcr(uic0er, 0x00000000); /* disable all */
|
|
mtdcr(uic0cr, 0x00000009); /* ATI & UIC1 crit are critical */
|
|
mtdcr(uic0pr, 0xfffffe13); /* per ref-board manual */
|
|
mtdcr(uic0tr, 0x01c00008); /* per ref-board manual */
|
|
mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */
|
|
mtdcr(uic0sr, 0xffffffff); /* clear all */
|
|
|
|
mtdcr(uic1sr, 0xffffffff); /* clear all */
|
|
mtdcr(uic1er, 0x00000000); /* disable all */
|
|
mtdcr(uic1cr, 0x00000000); /* all non-critical */
|
|
mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */
|
|
mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */
|
|
mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */
|
|
mtdcr(uic1sr, 0xffffffff); /* clear all */
|
|
|
|
/*
|
|
* Setup other serial configuration
|
|
*/
|
|
mfsdr(sdr_pci0, reg);
|
|
mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */
|
|
mtsdr(sdr_pfc0, 0x00003e00); /* Pin function */
|
|
mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins */
|
|
|
|
return 0;
|
|
}
|
|
|
|
int misc_init_r(void)
|
|
{
|
|
uint pbcr;
|
|
int size_val;
|
|
uint sz;
|
|
|
|
/* Re-do sizing to get full correct info */
|
|
mfebc(pb0cr, pbcr);
|
|
|
|
if (gd->bd->bi_flashsize > 0x08000000)
|
|
panic("Max. flash banksize is 128 MB!\n");
|
|
|
|
for (sz = gd->bd->bi_flashsize, size_val = 7;
|
|
((sz & 0x08000000) == 0) && (size_val > 0); --size_val)
|
|
sz <<= 1;
|
|
|
|
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
|
|
mtebc(pb0cr, pbcr);
|
|
|
|
/* adjust flash start and offset */
|
|
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
|
|
gd->bd->bi_flashoffset = 0;
|
|
|
|
/* Monitor protection ON by default */
|
|
(void)flash_protect(FLAG_PROTECT_SET,
|
|
-CONFIG_SYS_MONITOR_LEN,
|
|
0xffffffff,
|
|
&flash_info[0]);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
char *s = getenv("serial#");
|
|
|
|
printf("Board: GDPPC440ETX - G&D PPC440EP/GR ETX-module");
|
|
|
|
if (s != NULL) {
|
|
puts(", serial# ");
|
|
puts(s);
|
|
}
|
|
putc('\n');
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* pci_pre_init
|
|
*
|
|
* This routine is called just prior to registering the hose and gives
|
|
* the board the opportunity to check things. Returning a value of zero
|
|
* indicates that things are bad & PCI initialization should be aborted.
|
|
*
|
|
* Different boards may wish to customize the pci controller structure
|
|
* (add regions, override default access routines, etc) or perform
|
|
* certain pre-initialization actions.
|
|
*
|
|
*/
|
|
#if defined(CONFIG_PCI)
|
|
int pci_pre_init(struct pci_controller *hose)
|
|
{
|
|
unsigned long addr;
|
|
|
|
/*
|
|
* Set priority for all PLB3 devices to 0.
|
|
* Set PLB3 arbiter to fair mode.
|
|
*/
|
|
mfsdr(sdr_amp1, addr);
|
|
mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
|
|
addr = mfdcr(plb3_acr);
|
|
mtdcr(plb3_acr, addr | 0x80000000);
|
|
|
|
/*
|
|
* Set priority for all PLB4 devices to 0.
|
|
*/
|
|
mfsdr(sdr_amp0, addr);
|
|
mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
|
|
addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
|
|
mtdcr(plb4_acr, addr);
|
|
|
|
/*
|
|
* Set Nebula PLB4 arbiter to fair mode.
|
|
*/
|
|
/* Segment0 */
|
|
addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
|
|
addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
|
|
addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
|
|
addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
|
|
mtdcr(plb0_acr, addr);
|
|
|
|
/* Segment1 */
|
|
addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
|
|
addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
|
|
addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
|
|
addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
|
|
mtdcr(plb1_acr, addr);
|
|
|
|
/* enable 66 MHz ext. Clock */
|
|
out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x00008000);
|
|
out32(GPIO1_OR, in32(GPIO1_OR) | 0x00008000);
|
|
|
|
return 1;
|
|
}
|
|
#endif /* defined(CONFIG_PCI) */
|
|
|
|
/*
|
|
* pci_target_init
|
|
*
|
|
* The bootstrap configuration provides default settings for the pci
|
|
* inbound map (PIM). But the bootstrap config choices are limited and
|
|
* may not be sufficient for a given board.
|
|
*
|
|
*/
|
|
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
|
|
void pci_target_init(struct pci_controller *hose)
|
|
{
|
|
/*
|
|
* Set up Direct MMIO registers
|
|
*/
|
|
|
|
/*
|
|
* PowerPC440 EP PCI Master configuration.
|
|
* Map one 1Gig range of PLB/processor addresses to PCI memory space.
|
|
* PLB address 0xA0000000-0xDFFFFFFF
|
|
* ==> PCI address 0xA0000000-0xDFFFFFFF
|
|
* Use byte reversed out routines to handle endianess.
|
|
* Make this region non-prefetchable.
|
|
*/
|
|
out32r(PCIX0_PMM0MA, 0x00000000); /* disabled b4 setting */
|
|
out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);
|
|
out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
|
|
out32r(PCIX0_PMM0PCIHA, 0x00000000);
|
|
out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M, no prefetch, enable region */
|
|
|
|
out32r(PCIX0_PMM1MA, 0x00000000); /* disabled b4 setting */
|
|
out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);
|
|
out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
|
|
out32r(PCIX0_PMM1PCIHA, 0x00000000);
|
|
out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M, no prefetch, enable region */
|
|
|
|
out32r(PCIX0_PTM1MS, 0x00000001);
|
|
out32r(PCIX0_PTM1LA, 0);
|
|
out32r(PCIX0_PTM2MS, 0);
|
|
out32r(PCIX0_PTM2LA, 0);
|
|
|
|
/*
|
|
* Set up Configuration registers
|
|
*/
|
|
|
|
/* Program the board's subsystem id/vendor id */
|
|
pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
|
|
CONFIG_SYS_PCI_SUBSYS_VENDORID);
|
|
pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
|
|
|
|
/* Configure command register as bus master */
|
|
pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
|
|
|
|
/* 240nS PCI clock */
|
|
pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
|
|
|
|
/* No error reporting */
|
|
pci_write_config_word(0, PCI_ERREN, 0);
|
|
|
|
pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
|
|
|
|
}
|
|
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
|
|
|
|
/*
|
|
* pci_master_init
|
|
*
|
|
*/
|
|
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
|
|
void pci_master_init(struct pci_controller *hose)
|
|
{
|
|
unsigned short temp_short;
|
|
|
|
/*
|
|
* Write the PowerPC440 EP PCI Configuration regs.
|
|
* Enable PowerPC440 EP to be a master on the PCI bus (PMM).
|
|
* Enable PowerPC440 EP to act as a PCI memory target (PTM).
|
|
*/
|
|
pci_read_config_word(0, PCI_COMMAND, &temp_short);
|
|
pci_write_config_word(0, PCI_COMMAND,
|
|
temp_short | PCI_COMMAND_MASTER |
|
|
PCI_COMMAND_MEMORY);
|
|
}
|
|
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
|
|
|
|
/*
|
|
* is_pci_host
|
|
*
|
|
* This routine is called to determine if a pci scan should be
|
|
* performed. With various hardware environments (especially cPCI and
|
|
* PPMC) it's insufficient to depend on the state of the arbiter enable
|
|
* bit in the strap register, or generic host/adapter assumptions.
|
|
*
|
|
* Rather than hard-code a bad assumption in the general 440 code, the
|
|
* 440 pci code requires the board to decide at runtime.
|
|
*
|
|
* Return 0 for adapter mode, non-zero for host (monarch) mode.
|
|
*
|
|
*
|
|
*/
|
|
#if defined(CONFIG_PCI)
|
|
int is_pci_host(struct pci_controller *hose)
|
|
{
|
|
return 1;
|
|
}
|
|
#endif /* defined(CONFIG_PCI) */
|
|
|