upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
406 lines
16 KiB
406 lines
16 KiB
/*
|
|
* (C) Copyright 2005
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
|
|
/************************************************************************
|
|
* bamboo.h - configuration for BAMBOO board
|
|
***********************************************************************/
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* High Level Configuration Options
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_BAMBOO 1 /* Board is BAMBOO */
|
|
#define CONFIG_440EP 1 /* Specific PPC440EP support */
|
|
#define CONFIG_4xx 1 /* ... PPC4xx family */
|
|
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
|
|
|
|
/*
|
|
* Please note that, if NAND support is enabled, the 2nd ethernet port
|
|
* can't be used because of pin multiplexing. So, if you want to use the
|
|
* 2nd ethernet port you have to "undef" the following define.
|
|
*/
|
|
#define CONFIG_BAMBOO_NAND 1 /* enable nand flash support */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Base addresses -- Note these are effective addresses where the
|
|
* actual resources get mapped (not physical addresses)
|
|
*----------------------------------------------------------------------*/
|
|
#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
|
|
#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
|
|
#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
|
|
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
|
|
#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */
|
|
#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
|
|
#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
|
|
#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
|
|
#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
|
|
|
|
/*Don't change either of these*/
|
|
#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/
|
|
#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs*/
|
|
/*Don't change either of these*/
|
|
|
|
#define CFG_USB_DEVICE 0x50000000
|
|
#define CFG_NVRAM_BASE_ADDR 0x80000000
|
|
#define CFG_BOOT_BASE_ADDR 0xf0000000
|
|
#define CFG_NAND_ADDR 0x90000000
|
|
#define CFG_NAND2_ADDR 0x94000000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Initial RAM & stack pointer (placed in SDRAM)
|
|
*----------------------------------------------------------------------*/
|
|
#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */
|
|
#define CFG_INIT_RAM_END (4 << 10)
|
|
#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
|
|
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
|
|
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Serial Port
|
|
*----------------------------------------------------------------------*/
|
|
#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
|
|
#define CONFIG_BAUDRATE 115200
|
|
#define CONFIG_SERIAL_MULTI 1
|
|
/* define this if you want console on UART1 */
|
|
#undef CONFIG_UART1_CONSOLE
|
|
|
|
#define CFG_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* NVRAM/RTC
|
|
*
|
|
* NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF
|
|
* The DS1558 code assumes this condition
|
|
*
|
|
*----------------------------------------------------------------------*/
|
|
#define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */
|
|
#define CONFIG_RTC_DS1556 1 /* DS1556 RTC */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Environment
|
|
*----------------------------------------------------------------------*/
|
|
/*
|
|
* Define here the location of the environment variables (FLASH or EEPROM).
|
|
* Note: DENX encourages to use redundant environment in FLASH.
|
|
*/
|
|
#if 1
|
|
#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
|
|
#else
|
|
#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH related
|
|
*----------------------------------------------------------------------*/
|
|
#define CFG_MAX_FLASH_BANKS 3 /* number of banks */
|
|
#define CFG_MAX_FLASH_SECT 256 /* sectors per device */
|
|
|
|
#undef CFG_FLASH_CHECKSUM
|
|
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CFG_FLASH_ADDR0 0x555
|
|
#define CFG_FLASH_ADDR1 0x2aa
|
|
#define CFG_FLASH_WORD_SIZE unsigned char
|
|
|
|
#define CFG_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */
|
|
#define CFG_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */
|
|
|
|
#ifdef CFG_ENV_IS_IN_FLASH
|
|
#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
|
|
#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
|
|
#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
|
|
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
|
|
#endif /* CFG_ENV_IS_IN_FLASH */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* NAND-FLASH related
|
|
*----------------------------------------------------------------------*/
|
|
#define NAND_CMD_REG (0x00) /* NandFlash Command Register */
|
|
#define NAND_ADDR_REG (0x04) /* NandFlash Address Register */
|
|
#define NAND_DATA_REG (0x08) /* NandFlash Data Register */
|
|
#define NAND_ECC0_REG (0x10) /* NandFlash ECC Register0 */
|
|
#define NAND_ECC1_REG (0x14) /* NandFlash ECC Register1 */
|
|
#define NAND_ECC2_REG (0x18) /* NandFlash ECC Register2 */
|
|
#define NAND_ECC3_REG (0x1C) /* NandFlash ECC Register3 */
|
|
#define NAND_ECC4_REG (0x20) /* NandFlash ECC Register4 */
|
|
#define NAND_ECC5_REG (0x24) /* NandFlash ECC Register5 */
|
|
#define NAND_ECC6_REG (0x28) /* NandFlash ECC Register6 */
|
|
#define NAND_ECC7_REG (0x2C) /* NandFlash ECC Register7 */
|
|
#define NAND_CR0_REG (0x30) /* NandFlash Device Bank0 Config Register */
|
|
#define NAND_CR1_REG (0x34) /* NandFlash Device Bank1 Config Register */
|
|
#define NAND_CR2_REG (0x38) /* NandFlash Device Bank2 Config Register */
|
|
#define NAND_CR3_REG (0x3C) /* NandFlash Device Bank3 Config Register */
|
|
#define NAND_CCR_REG (0x40) /* NandFlash Core Configuration Register */
|
|
#define NAND_STAT_REG (0x44) /* NandFlash Device Status Register */
|
|
#define NAND_HWCTL_REG (0x48) /* NandFlash Direct Hwd Control Register */
|
|
#define NAND_REVID_REG (0x50) /* NandFlash Core Revision Id Register */
|
|
|
|
/* Nand Flash K9F1208U0A Command Set => Nand Flash 0 */
|
|
#define NAND0_CMD_READ1_HALF1 0x00 /* Starting addr for 1rst half of registers */
|
|
#define NAND0_CMD_READ1_HALF2 0x01 /* Starting addr for 2nd half of registers */
|
|
#define NAND0_CMD_READ2 0x50
|
|
#define NAND0_CMD_READ_ID 0x90
|
|
#define NAND0_CMD_READ_STATUS 0x70
|
|
#define NAND0_CMD_RESET 0xFF
|
|
#define NAND0_CMD_PAGE_PROG 0x80
|
|
#define NAND0_CMD_PAGE_PROG_TRUE 0x10
|
|
#define NAND0_CMD_PAGE_PROG_DUMMY 0x11
|
|
#define NAND0_CMD_BLOCK_ERASE 0x60
|
|
#define NAND0_CMD_BLOCK_ERASE_END 0xD0
|
|
|
|
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
|
|
#define SECTORSIZE 512
|
|
|
|
#define ADDR_COLUMN 1
|
|
#define ADDR_PAGE 2
|
|
#define ADDR_COLUMN_PAGE 3
|
|
|
|
#define NAND_ChipID_UNKNOWN 0x00
|
|
#define NAND_MAX_FLOORS 1
|
|
#define NAND_MAX_CHIPS 1
|
|
|
|
#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_CMD_REG) = d;} while(0)
|
|
#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_ADDR_REG) = d;} while(0)
|
|
#define WRITE_NAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_DATA_REG) = d;} while(0)
|
|
#define READ_NAND(adr) (*(volatile u8 *)((ulong)adr+NAND_DATA_REG))
|
|
#define NAND_WAIT_READY(nand) while (!(*(volatile u8 *)((ulong)nand->IO_ADDR+NAND_STAT_REG) & 0x01))
|
|
|
|
/* not needed with 440EP NAND controller */
|
|
#define NAND_CTL_CLRALE(nandptr)
|
|
#define NAND_CTL_SETALE(nandptr)
|
|
#define NAND_CTL_CLRCLE(nandptr)
|
|
#define NAND_CTL_SETCLE(nandptr)
|
|
#define NAND_DISABLE_CE(nand)
|
|
#define NAND_ENABLE_CE(nand)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* DDR SDRAM
|
|
*----------------------------------------------------------------------------- */
|
|
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
|
|
#undef CONFIG_DDR_ECC /* don't use ECC */
|
|
#define CFG_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */
|
|
#define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51}
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* I2C
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
|
|
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
|
|
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
|
|
#define CFG_I2C_SLAVE 0x7F
|
|
|
|
#define CFG_I2C_MULTI_EEPROMS
|
|
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
|
|
#define CFG_I2C_EEPROM_ADDR_LEN 1
|
|
#define CFG_EEPROM_PAGE_WRITE_ENABLE
|
|
#define CFG_EEPROM_PAGE_WRITE_BITS 3
|
|
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
|
|
|
|
#ifdef CFG_ENV_IS_IN_EEPROM
|
|
#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */
|
|
#define CFG_ENV_OFFSET 0x0
|
|
#endif /* CFG_ENV_IS_IN_EEPROM */
|
|
|
|
#define CONFIG_PREBOOT "echo;" \
|
|
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
|
|
"echo"
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"hostname=bamboo\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"addip=setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
|
":${hostname}:${netdev}:off panic=1\0" \
|
|
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
|
|
"flash_nfs=run nfsargs addip addtty;" \
|
|
"bootm ${kernel_addr}\0" \
|
|
"flash_self=run ramargs addip addtty;" \
|
|
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
|
|
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
|
|
"bootm\0" \
|
|
"rootpath=/opt/eldk/ppc_4xx\0" \
|
|
"bootfile=/tftpboot/bamboo/uImage\0" \
|
|
"kernel_addr=fff00000\0" \
|
|
"ramdisk_addr=fff10000\0" \
|
|
"load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \
|
|
"update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \
|
|
"cp.b 100000 fff80000 80000;" \
|
|
"setenv filesize;saveenv\0" \
|
|
"upd=run load;run update\0" \
|
|
""
|
|
#define CONFIG_BOOTCOMMAND "run flash_self"
|
|
|
|
#if 0
|
|
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
|
|
#else
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
#endif
|
|
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
|
|
#define CONFIG_PHY1_ADDR 1
|
|
|
|
#ifndef CONFIG_BAMBOO_NAND
|
|
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
|
|
#endif /* CONFIG_BAMBOO_NAND */
|
|
|
|
#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
|
|
|
|
#define CONFIG_NETCONSOLE /* include NetConsole support */
|
|
#define CONFIG_NET_MULTI 1 /* required for netconsole */
|
|
|
|
/* Partitions */
|
|
#define CONFIG_MAC_PARTITION
|
|
#define CONFIG_DOS_PARTITION
|
|
#define CONFIG_ISO_PARTITION
|
|
|
|
#ifdef CONFIG_440EP
|
|
/* USB */
|
|
#define CONFIG_USB_OHCI
|
|
#define CONFIG_USB_STORAGE
|
|
|
|
/*Comment this out to enable USB 1.1 device*/
|
|
#define USB_2_0_DEVICE
|
|
#endif /*CONFIG_440EP*/
|
|
|
|
#ifdef CONFIG_BAMBOO_NAND
|
|
#define _CFG_CMD_NAND CFG_CMD_NAND
|
|
#else
|
|
#define _CFG_CMD_NAND 0
|
|
#endif /* CONFIG_BAMBOO_NAND */
|
|
|
|
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
|
|
CFG_CMD_ASKENV | \
|
|
CFG_CMD_EEPROM | \
|
|
CFG_CMD_DATE | \
|
|
CFG_CMD_DHCP | \
|
|
CFG_CMD_DIAG | \
|
|
CFG_CMD_ELF | \
|
|
CFG_CMD_I2C | \
|
|
CFG_CMD_IRQ | \
|
|
CFG_CMD_MII | \
|
|
CFG_CMD_NET | \
|
|
CFG_CMD_NFS | \
|
|
CFG_CMD_PCI | \
|
|
CFG_CMD_PING | \
|
|
CFG_CMD_REGINFO | \
|
|
CFG_CMD_SDRAM | \
|
|
CFG_CMD_USB | \
|
|
CFG_CMD_FAT | \
|
|
CFG_CMD_EXT2 | \
|
|
_CFG_CMD_NAND | \
|
|
CFG_CMD_SNTP )
|
|
|
|
#define CONFIG_SUPPORT_VFAT
|
|
|
|
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
|
|
#include <cmd_confdefs.h>
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CFG_LONGHELP /* undef to save memory */
|
|
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
|
|
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
|
|
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
|
|
#define CFG_MAXARGS 16 /* max number of command args */
|
|
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CFG_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
|
|
#define CONFIG_LYNXKDI 1 /* support kdi files */
|
|
|
|
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCI stuff
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
/* General PCI */
|
|
#define CONFIG_PCI /* include pci support */
|
|
#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
|
|
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
|
|
|
|
/* Board-specific PCI */
|
|
#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
|
|
#define CFG_PCI_TARGET_INIT
|
|
#define CFG_PCI_MASTER_INIT
|
|
|
|
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
|
|
#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
|
|
#define CFG_CACHELINE_SIZE 32 /* ... */
|
|
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
|
|
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*
|
|
* Internal Definitions
|
|
*
|
|
* Boot Flags
|
|
*/
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
|
|
|
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
|
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
|
|
#endif
|
|
#endif /* __CONFIG_H */
|
|
|