upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/drivers/usb/host/ehci-mx6.c

196 lines
5.1 KiB

/*
* Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
* Copyright (C) 2010 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <usb.h>
#include <errno.h>
#include <linux/compiler.h>
#include <usb/ehci-fsl.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/clock.h>
#include <asm/imx-common/iomux-v3.h>
#include "ehci.h"
#define USB_OTGREGS_OFFSET 0x000
#define USB_H1REGS_OFFSET 0x200
#define USB_H2REGS_OFFSET 0x400
#define USB_H3REGS_OFFSET 0x600
#define USB_OTHERREGS_OFFSET 0x800
#define USB_H1_CTRL_OFFSET 0x04
#define USBPHY_CTRL 0x00000030
#define USBPHY_CTRL_SET 0x00000034
#define USBPHY_CTRL_CLR 0x00000038
#define USBPHY_CTRL_TOG 0x0000003c
#define USBPHY_PWD 0x00000000
#define USBPHY_CTRL_SFTRST 0x80000000
#define USBPHY_CTRL_CLKGATE 0x40000000
#define USBPHY_CTRL_ENUTMILEVEL3 0x00008000
#define USBPHY_CTRL_ENUTMILEVEL2 0x00004000
#define ANADIG_USB2_CHRG_DETECT_EN_B 0x00100000
#define ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B 0x00080000
#define ANADIG_USB2_PLL_480_CTRL_BYPASS 0x00010000
#define ANADIG_USB2_PLL_480_CTRL_ENABLE 0x00002000
#define ANADIG_USB2_PLL_480_CTRL_POWER 0x00001000
#define ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS 0x00000040
#define UCTRL_OVER_CUR_POL (1 << 8) /* OTG Polarity of Overcurrent */
#define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection */
/* USBCMD */
#define UH1_USBCMD_OFFSET 0x140
#define UCMD_RUN_STOP (1 << 0) /* controller run/stop */
#define UCMD_RESET (1 << 1) /* controller reset */
static void usbh1_internal_phy_clock_gate(int on)
{
void __iomem *phy_reg = (void __iomem *)USB_PHY1_BASE_ADDR;
phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET;
__raw_writel(USBPHY_CTRL_CLKGATE, phy_reg);
}
static void usbh1_power_config(void)
{
struct anatop_regs __iomem *anatop =
(struct anatop_regs __iomem *)ANATOP_BASE_ADDR;
/*
* Some phy and power's special controls for host1
* 1. The external charger detector needs to be disabled
* or the signal at DP will be poor
* 2. The PLL's power and output to usb for host 1
* is totally controlled by IC, so the Software only needs
* to enable them at initializtion.
*/
__raw_writel(ANADIG_USB2_CHRG_DETECT_EN_B |
ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B,
&anatop->usb2_chrg_detect);
__raw_writel(ANADIG_USB2_PLL_480_CTRL_BYPASS,
&anatop->usb2_pll_480_ctrl_clr);
__raw_writel(ANADIG_USB2_PLL_480_CTRL_ENABLE |
ANADIG_USB2_PLL_480_CTRL_POWER |
ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS,
&anatop->usb2_pll_480_ctrl_set);
}
static int usbh1_phy_enable(void)
{
void __iomem *phy_reg = (void __iomem *)USB_PHY1_BASE_ADDR;
void __iomem *phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
void __iomem *usb_cmd = (void __iomem *)(USBOH3_USB_BASE_ADDR +
USB_H1REGS_OFFSET +
UH1_USBCMD_OFFSET);
u32 val;
/* Stop then Reset */
val = __raw_readl(usb_cmd);
val &= ~UCMD_RUN_STOP;
__raw_writel(val, usb_cmd);
while (__raw_readl(usb_cmd) & UCMD_RUN_STOP)
;
val = __raw_readl(usb_cmd);
val |= UCMD_RESET;
__raw_writel(val, usb_cmd);
while (__raw_readl(usb_cmd) & UCMD_RESET)
;
/* Reset USBPHY module */
val = __raw_readl(phy_ctrl);
val |= USBPHY_CTRL_SFTRST;
__raw_writel(val, phy_ctrl);
udelay(10);
/* Remove CLKGATE and SFTRST */
val = __raw_readl(phy_ctrl);
val &= ~(USBPHY_CTRL_CLKGATE | USBPHY_CTRL_SFTRST);
__raw_writel(val, phy_ctrl);
udelay(10);
/* Power up the PHY */
__raw_writel(0, phy_reg + USBPHY_PWD);
/* enable FS/LS device */
val = __raw_readl(phy_reg + USBPHY_CTRL);
val |= (USBPHY_CTRL_ENUTMILEVEL2 | USBPHY_CTRL_ENUTMILEVEL3);
__raw_writel(val, phy_reg + USBPHY_CTRL);
return 0;
}
static void usbh1_oc_config(void)
{
void __iomem *usb_base = (void __iomem *)USBOH3_USB_BASE_ADDR;
void __iomem *usbother_base = usb_base + USB_OTHERREGS_OFFSET;
u32 val;
val = __raw_readl(usbother_base + USB_H1_CTRL_OFFSET);
#if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
/* mx6qarm2 seems to required a different setting*/
val &= ~UCTRL_OVER_CUR_POL;
#else
val |= UCTRL_OVER_CUR_POL;
#endif
__raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET);
val = __raw_readl(usbother_base + USB_H1_CTRL_OFFSET);
val |= UCTRL_OVER_CUR_DIS;
__raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET);
}
int __weak board_ehci_hcd_init(int port)
{
return 0;
}
int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
struct usb_ehci *ehci;
enable_usboh3_clk(1);
mdelay(1);
/* Do board specific initialization */
board_ehci_hcd_init(CONFIG_MXC_USB_PORT);
#if CONFIG_MXC_USB_PORT == 1
/* USB Host 1 */
usbh1_power_config();
usbh1_oc_config();
usbh1_internal_phy_clock_gate(1);
usbh1_phy_enable();
#else
#error "MXC USB port not yet supported"
#endif
ehci = (struct usb_ehci *)(USBOH3_USB_BASE_ADDR +
(0x200 * CONFIG_MXC_USB_PORT));
*hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
*hcor = (struct ehci_hcor *)((uint32_t)*hccr +
HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
setbits_le32(&ehci->usbmode, CM_HOST);
__raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
setbits_le32(&ehci->portsc, USB_EN);
mdelay(10);
return 0;
}
int ehci_hcd_stop(int index)
{
return 0;
}