upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/include/configs/M5249EVB.h

188 lines
6.5 KiB

/*
* Configuation settings for the esd TASREG board.
*
* (C) Copyright 2004
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef _M5249EVB_H
#define _M5249EVB_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MCFTMR
#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
#undef CONFIG_WATCHDOG
#undef CONFIG_MONITOR_IS_IN_RAM /* no pre-loader required!!! ;-) */
/*
* BOOTP options
*/
#undef CONFIG_BOOTP_BOOTFILESIZE
#undef CONFIG_BOOTP_BOOTPATH
#undef CONFIG_BOOTP_GATEWAY
#undef CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#define CONFIG_CMD_CACHE
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup */
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */
#define CONFIG_SYS_MEMTEST_START 0x400
#define CONFIG_SYS_MEMTEST_END 0x380000
/*
* Clock configuration: enable only one of the following options
*/
#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */
#define CONFIG_SYS_FAST_CLK 1 /* MCF5249 can run at 140MHz */
#define CONFIG_SYS_CLK 132025600 /* MCF5249 can run at 140MHz */
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */
#define CONFIG_SYS_MBAR2 0x80000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_ENV_IS_IN_FLASH 1
#define LDS_BOARD_TEXT \
. = DEFINED(env_offset) ? env_offset : .; \
common/env_embedded.o (.text);
#define CONFIG_ENV_OFFSET 0x4000 /* Address of Environment Sector*/
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
#define CONFIG_ENV_SECT_SIZE 0x2000 /* see README - env sector total size */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
#define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE)
#if 0 /* test-only */
#define CONFIG_PRAM 512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */
#endif
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
#define CONFIG_SYS_MONITOR_LEN 0x20000
#define CONFIG_SYS_MALLOC_LEN (1 * 1024*1024) /* Reserve 1 MB for malloc() */
#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_FLASH_CFI
#ifdef CONFIG_SYS_FLASH_CFI
# define CONFIG_FLASH_CFI_DRIVER 1
# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
# define CONFIG_SYS_FLASH_CHECKSUM
# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM)
#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \
CF_ADDRMASK(2) | \
CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \
CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \
CF_CACR_DBWE)
/*-----------------------------------------------------------------------
* Memory bank definitions
*/
/* CS0 - AMD Flash, address 0xffc00000 */
#define CONFIG_SYS_CS0_BASE 0xffe00000
#define CONFIG_SYS_CS0_CTRL 0x00001980 /* WS=0110, AA=1, PS=10 */
/** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/
#define CONFIG_SYS_CS0_MASK 0x003f0021 /* 4MB, AA=0, WP=0, C/I=1, V=1 */
/* CS1 - FPGA, address 0xe0000000 */
#define CONFIG_SYS_CS1_BASE 0xe0000000
#define CONFIG_SYS_CS1_CTRL 0x00000d80 /* WS=0011, AA=1, PS=10 */
#define CONFIG_SYS_CS1_MASK 0x00010001 /* 128kB, AA=0, WP=0, C/I=0, V=1*/
/*-----------------------------------------------------------------------
* Port configuration
*/
#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */
#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54*/
#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */
#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */
#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */
#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */
#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */
#endif /* M5249 */