upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/include/configs/stxssa.h

441 lines
14 KiB

/*
* (C) Copyright 2005 Embedded Alley Solutions, Inc.
* Dan Malek <dan@embeddedalley.com>
* Copied from STx GP3.
* Updates for Silicon Tx GP3 SSA board.
*
* (C) Copyright 2002,2003 Motorola,Inc.
* Xianghua Xiao <X.Xiao@motorola.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/* mpc8560ads board configuration file */
/* please refer to doc/README.mpc85xx for more info */
/* make sure you change the MAC address and other network params first,
* search for CONFIG_SERVERIP, etc. in this file
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_CPM2 1 /* has CPM2 */
#define CONFIG_STXSSA 1 /* Silicon Tx GPPP SSA board specific*/
#define CONFIG_MPC8560 1
#define CONFIG_SYS_TEXT_BASE 0xFFF80000
#define CONFIG_PCI /* PCI ethernet support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_TSEC_ENET /* tsec ethernet support*/
#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
/* sysclk for MPC85xx
*/
#define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */
/* Blinkin' LEDs for Robert :-)
*/
#define CONFIG_SHOW_ACTIVITY 1
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x00400000
/* Localbus connector. There are many options that can be
* connected here, including sdram or lots of flash.
* This address, however, is used to configure a 256M local bus
* window that includes the Config latch below.
*/
#define CONFIG_SYS_LBC_OPTION_BASE 0xF0000000 /* Localbus Extension */
#define CONFIG_SYS_LBC_OPTION_SIZE 256 /* 256MB */
/* There are various flash options used, we configure for the largest,
* which is 64Mbytes. The CFI works fine and will discover the proper
* sizes.
*/
#ifdef CONFIG_STXSSA_4M
#define CONFIG_SYS_FLASH_BASE 0xFFC00000 /* start of 4 MiB flash */
#else
#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* start of 64 MiB flash */
#endif
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | 0x1801) /* port size 32bit */
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_FLASH_BASE | 0x0FF7)
#define CONFIG_SYS_FLASH_CFI 1
#define CONFIG_FLASH_CFI_DRIVER 1
#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#define CONFIG_SYS_FLASH_PROTECTION
/* The configuration latch is Chip Select 1.
* It's an 8-bit latch in the lower 8 bits of the word.
*/
#define CONFIG_SYS_LBC_CFGLATCH_BASE 0xFB000000 /* Base of config latch */
#define CONFIG_SYS_BR1_PRELIM 0xFB001801 /* 32-bit port */
#define CONFIG_SYS_OR1_PRELIM 0xFFFF0FF7 /* 64K is enough */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef CONFIG_SYS_RAMBOOT
#endif
#ifdef CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */
#endif
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
/* I2C addresses of SPD EEPROMs */
#define SPD_EEPROM_ADDRESS 0x54 /* CTLR 0 DIMM 0 */
#undef CONFIG_CLOCKS_IN_MHZ
/* local bus definitions */
#define CONFIG_SYS_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
#define CONFIG_SYS_OR2_PRELIM 0xfc006901
#define CONFIG_SYS_LBC_LCRR 0x00030004 /* local bus freq */
#define CONFIG_SYS_LBC_LBCR 0x00000000
#define CONFIG_SYS_LBC_LSRT 0x20000000
#define CONFIG_SYS_LBC_MRTPR 0x20000000
#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723
#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723
#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723
#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723
#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 2
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/*
* I2C
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#undef CONFIG_SYS_I2C_NOPROBES
/* I2C RTC */
#define CONFIG_RTC_DS1337 /* This is really a DS1339 RTC */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/* I2C EEPROM. AT24C32, we keep our environment in here.
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51 /* 1010001x */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
/*
* Standard 8555 PCI mapping.
* Addresses are mapped 1-1.
*/
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */
#define CONFIG_SYS_PCI2_MEM_BASE 0xa0000000
#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
#define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
#define CONFIG_SYS_PCI2_IO_PHYS 0xe3000000
#define CONFIG_SYS_PCI2_IO_SIZE 0x01000000 /* 16M */
#if defined(CONFIG_PCI) /* PCI Ethernet card */
#define CONFIG_MPC85XX_PCI2 1
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_EEPRO100
#define CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 4
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC1_FLAGS TSEC_GIGABIT
#define TSEC2_FLAGS TSEC_GIGABIT
#define CONFIG_ETHPRIME "TSEC0"
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
#define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */
#undef CONFIG_ETHER_NONE /* define if ether on something else */
#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
#if (CONFIG_ETHER_INDEX == 2)
/*
* - Rx-CLK is CLK13
* - Tx-CLK is CLK14
* - Select bus for bd/buffers
* - Full duplex
*/
#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
#define CONFIG_SYS_CPMFCR_RAMTYPE 0
#if 0
#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE)
#else
#define CONFIG_SYS_FCC_PSMR 0
#endif
#define FETH2_RST 0x01
#elif (CONFIG_ETHER_INDEX == 3)
/* need more definitions here for FE3 */
#define FETH3_RST 0x80
#endif /* CONFIG_ETHER_INDEX */
/* MDIO is done through the TSEC0 control.
*/
#define CONFIG_MII /* MII PHY management */
#undef CONFIG_BITBANGMII /* bit-bang MII PHY management */
#endif
/* Environment - default config is in flash, see below */
#if 0 /* in EEPROM */
# define CONFIG_ENV_IS_IN_EEPROM 1
# define CONFIG_ENV_OFFSET 0
# define CONFIG_ENV_SIZE 2048
#else /* in flash */
# define CONFIG_ENV_IS_IN_FLASH 1
# ifdef CONFIG_STXSSA_4M
# define CONFIG_ENV_SECT_SIZE 0x20000
# else /* default configuration - 64 MiB flash */
# define CONFIG_ENV_SECT_SIZE 0x40000
# endif
# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
# define CONFIG_ENV_SIZE 0x4000
# define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
# define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_TIMESTAMP /* Print image info with ts */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_I2C
#define CONFIG_CMD_PING
#define CONFIG_CMD_SNTP
#define CONFIG_CMD_REGINFO
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
#define CONFIG_CMD_MII
#endif
#if !defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_CMD_ELF
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "SSA=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#endif
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#endif
/*
* Environment in EEPROM is compatible with different flash sector sizes,
* but only little space is available, so we use a very simple setup.
* With environment in flash, we use a more powerful default configuration.
*/
#ifdef CONFIG_ENV_IS_IN_EEPROM /* use restricted "standard" environment */
#define CONFIG_BAUDRATE 38400
#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
#define CONFIG_BOOTCOMMAND "bootm 0xffc00000 0xffd00000"
#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,$baudrate"
#define CONFIG_SERVERIP 192.168.85.1
#define CONFIG_IPADDR 192.168.85.60
#define CONFIG_GATEWAYIP 192.168.85.1
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_HOSTNAME STX_SSA
#define CONFIG_ROOTPATH "/gppproot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_LOADADDR 0x1000000
#else /* ENV IS IN FLASH -- use a full-blown envionment */
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */
#define CONFIG_PREBOOT "echo;" \
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hostname=gp3ssa\0" \
"bootfile=/tftpboot/gp3ssa/uImage\0" \
"loadaddr=400000\0" \
"netdev=eth0\0" \
"consdev=ttyS1\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs $bootargs " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask" \
":$hostname:$netdev:off panic=1\0" \
"addcons=setenv bootargs $bootargs " \
"console=$consdev,$baudrate\0" \
"flash_nfs=run nfsargs addip addcons;" \
"bootm $kernel_addr\0" \
"flash_self=run ramargs addip addcons;" \
"bootm $kernel_addr $ramdisk_addr\0" \
"net_nfs=tftp $loadaddr $bootfile;" \
"run nfsargs addip addcons;bootm\0" \
"rootpath=/opt/eldk/ppc_85xx\0" \
"kernel_addr=FC000000\0" \
"ramdisk_addr=FC200000\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#endif /* CONFIG_ENV_IS_IN_EEPROM */
#endif /* __CONFIG_H */