upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/samsung/common/board.c

323 lines
6.7 KiB

/*
* (C) Copyright 2013 SAMSUNG Electronics
* Rajeshwari Shinde <rajeshwari.s@samsung.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <cros_ec.h>
#include <errno.h>
#include <fdtdec.h>
#include <spi.h>
#include <tmu.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/arch/board.h>
#include <asm/arch/cpu.h>
#include <asm/arch/dwmmc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/power.h>
#include <power/pmic.h>
#include <asm/arch/sromc.h>
#include <lcd.h>
#include <samsung/misc.h>
DECLARE_GLOBAL_DATA_PTR;
int __exynos_early_init_f(void)
{
return 0;
}
int exynos_early_init_f(void)
__attribute__((weak, alias("__exynos_early_init_f")));
int __exynos_power_init(void)
{
return 0;
}
int exynos_power_init(void)
__attribute__((weak, alias("__exynos_power_init")));
#if defined CONFIG_EXYNOS_TMU
/* Boot Time Thermal Analysis for SoC temperature threshold breach */
static void boot_temp_check(void)
{
int temp;
switch (tmu_monitor(&temp)) {
case TMU_STATUS_NORMAL:
break;
case TMU_STATUS_TRIPPED:
/*
* Status TRIPPED ans WARNING means corresponding threshold
* breach
*/
puts("EXYNOS_TMU: TRIPPING! Device power going down ...\n");
set_ps_hold_ctrl();
hang();
break;
case TMU_STATUS_WARNING:
puts("EXYNOS_TMU: WARNING! Temperature very high\n");
break;
case TMU_STATUS_INIT:
/*
* TMU_STATUS_INIT means something is wrong with temperature
* sensing and TMU status was changed back from NORMAL to INIT.
*/
puts("EXYNOS_TMU: WARNING! Temperature sensing not done\n");
break;
default:
debug("EXYNOS_TMU: Unknown TMU state\n");
}
}
#endif
int board_init(void)
{
gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
#if defined CONFIG_EXYNOS_TMU
if (tmu_init(gd->fdt_blob) != TMU_STATUS_NORMAL) {
debug("%s: Failed to init TMU\n", __func__);
return -1;
}
boot_temp_check();
#endif
#ifdef CONFIG_EXYNOS_SPI
spi_init();
#endif
return exynos_init();
}
int dram_init(void)
{
int i;
u32 addr;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
}
return 0;
}
void dram_init_banksize(void)
{
int i;
u32 addr, size;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
gd->bd->bi_dram[i].start = addr;
gd->bd->bi_dram[i].size = size;
}
}
static int board_uart_init(void)
{
int err, uart_id, ret = 0;
for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
if (err) {
debug("UART%d not configured\n",
(uart_id - PERIPH_ID_UART0));
ret |= err;
}
}
return ret;
}
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
int err;
err = board_uart_init();
if (err) {
debug("UART init failed\n");
return err;
}
#ifdef CONFIG_SYS_I2C_INIT_BOARD
board_i2c_init(gd->fdt_blob);
#endif
return exynos_early_init_f();
}
#endif
#if defined(CONFIG_POWER)
int power_init_board(void)
{
set_ps_hold_ctrl();
return exynos_power_init();
}
#endif
#ifdef CONFIG_OF_CONTROL
#ifdef CONFIG_SMC911X
static int decode_sromc(const void *blob, struct fdt_sromc *config)
{
int err;
int node;
node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
if (node < 0) {
debug("Could not find SROMC node\n");
return node;
}
config->bank = fdtdec_get_int(blob, node, "bank", 0);
config->width = fdtdec_get_int(blob, node, "width", 2);
err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
FDT_SROM_TIMING_COUNT);
if (err < 0) {
debug("Could not decode SROMC configuration Error: %s\n",
fdt_strerror(err));
return -FDT_ERR_NOTFOUND;
}
return 0;
}
#endif
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_SMC911X
u32 smc_bw_conf, smc_bc_conf;
struct fdt_sromc config;
fdt_addr_t base_addr;
int node;
node = decode_sromc(gd->fdt_blob, &config);
if (node < 0) {
debug("%s: Could not find sromc configuration\n", __func__);
return 0;
}
node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
if (node < 0) {
debug("%s: Could not find lan9215 configuration\n", __func__);
return 0;
}
/* We now have a node, so any problems from now on are errors */
base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
if (base_addr == FDT_ADDR_T_NONE) {
debug("%s: Could not find lan9215 address\n", __func__);
return -1;
}
/* Ethernet needs data bus width of 16 bits */
if (config.width != 2) {
debug("%s: Unsupported bus width %d\n", __func__,
config.width);
return -1;
}
smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
| SROMC_BYTE_ENABLE(config.bank);
smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) |
SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |
SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |
SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |
SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) |
SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |
SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
/* Select and configure the SROMC bank */
exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
return smc911x_initialize(0, base_addr);
#endif
return 0;
}
#ifdef CONFIG_GENERIC_MMC
int board_mmc_init(bd_t *bis)
{
int ret;
#ifdef CONFIG_DWMMC
/* dwmmc initializattion for available channels */
ret = exynos_dwmmc_init(gd->fdt_blob);
if (ret)
debug("dwmmc init failed\n");
#endif
#ifdef CONFIG_SDHCI
/* mmc initializattion for available channels */
ret = exynos_mmc_init(gd->fdt_blob);
if (ret)
debug("mmc init failed\n");
#endif
return ret;
}
#endif
#ifdef CONFIG_DISPLAY_BOARDINFO
int checkboard(void)
{
const char *board_name;
board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL);
printf("Board: %s\n", board_name ? board_name : "unknown");
return 0;
}
#endif
#endif /* CONFIG_OF_CONTROL */
#ifdef CONFIG_BOARD_LATE_INIT
int board_late_init(void)
{
stdio_print_current_devices();
if (cros_ec_get_error()) {
/* Force console on */
gd->flags &= ~GD_FLG_SILENT;
printf("cros-ec communications failure %d\n",
cros_ec_get_error());
puts("\nPlease reset with Power+Refresh\n\n");
panic("Cannot init cros-ec device");
return -1;
}
return 0;
}
#endif
int arch_early_init_r(void)
{
#ifdef CONFIG_CROS_EC
if (cros_ec_board_init()) {
printf("%s: Failed to init EC\n", __func__);
return 0;
}
#endif
return 0;
}
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
set_board_info();
#endif
#ifdef CONFIG_LCD_MENU
keys_init();
check_boot_mode();
#endif
#ifdef CONFIG_CMD_BMP
if (panel_info.logo_on)
draw_logo();
#endif
return 0;
}
#endif