upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
146 lines
3.6 KiB
146 lines
3.6 KiB
/*
|
|
* (C) Copyright 2011
|
|
* eInfochips Ltd. <www.einfochips.com>
|
|
* Written-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
|
|
*
|
|
* Based on Aspenite:
|
|
* (C) Copyright 2010
|
|
* Marvell Semiconductor <www.marvell.com>
|
|
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
* Contributor: Mahavir Jain <mjain@marvell.com>
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
|
|
* MA 02110-1301 USA
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <mvmfp.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/mfp.h>
|
|
#include <asm/arch/armada100.h>
|
|
#include <asm/gpio.h>
|
|
#include <miiphy.h>
|
|
|
|
#ifdef CONFIG_ARMADA100_FEC
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#endif /* CONFIG_ARMADA100_FEC */
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
u32 mfp_cfg[] = {
|
|
/* I2C */
|
|
MFP105_CI2C_SDA,
|
|
MFP106_CI2C_SCL,
|
|
|
|
/* Enable Console on UART3 */
|
|
MFPO8_UART3_TXD,
|
|
MFPO9_UART3_RXD,
|
|
|
|
/* Ethernet PHY Interface */
|
|
MFP086_ETH_TXCLK,
|
|
MFP087_ETH_TXEN,
|
|
MFP088_ETH_TXDQ3,
|
|
MFP089_ETH_TXDQ2,
|
|
MFP090_ETH_TXDQ1,
|
|
MFP091_ETH_TXDQ0,
|
|
MFP092_ETH_CRS,
|
|
MFP093_ETH_COL,
|
|
MFP094_ETH_RXCLK,
|
|
MFP095_ETH_RXER,
|
|
MFP096_ETH_RXDQ3,
|
|
MFP097_ETH_RXDQ2,
|
|
MFP098_ETH_RXDQ1,
|
|
MFP099_ETH_RXDQ0,
|
|
MFP100_ETH_MDC,
|
|
MFP101_ETH_MDIO,
|
|
MFP103_ETH_RXDV,
|
|
|
|
/* SSP2 */
|
|
MFP107_SSP2_RXD,
|
|
MFP108_SSP2_TXD,
|
|
MFP110_SSP2_CS,
|
|
MFP111_SSP2_CLK,
|
|
|
|
MFP_EOC /*End of configuration*/
|
|
};
|
|
/* configure MFP's */
|
|
mfp_config(mfp_cfg);
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
struct armd1apb2_registers *apb2_regs =
|
|
(struct armd1apb2_registers *)ARMD1_APBC2_BASE;
|
|
|
|
/* arch number of Board */
|
|
gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD;
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100;
|
|
/* Assert PHY_RST# */
|
|
gpio_direction_output(CONFIG_SYS_GPIO_PHY_RST, GPIO_LOW);
|
|
udelay(10);
|
|
/* Deassert PHY_RST# */
|
|
gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_HIGH);
|
|
|
|
/* Enable SSP2 clock */
|
|
writel(SSP2_APBCLK | SSP2_FNCLK, &apb2_regs->ssp2_clkrst);
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_ARMADA100_FEC
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
struct armd1apmu_registers *apmu_regs =
|
|
(struct armd1apmu_registers *)ARMD1_APMU_BASE;
|
|
|
|
/* Enable clock of ethernet controller */
|
|
writel(FE_CLK_RST | FE_CLK_ENA, &apmu_regs->fecrc);
|
|
|
|
return armada100_fec_register(ARMD1_FEC_BASE);
|
|
}
|
|
|
|
#ifdef CONFIG_RESET_PHY_R
|
|
/* Configure and initialize PHY chip 88E3015 */
|
|
void reset_phy(void)
|
|
{
|
|
u16 phy_adr;
|
|
const char *name = "armd-fec0";
|
|
|
|
if (miiphy_set_current_dev(name))
|
|
return;
|
|
|
|
/* command to read PHY dev address */
|
|
if (miiphy_read(name, 0xff, 0xff, &phy_adr)) {
|
|
printf("Err..%s could not read PHY dev address\n", __func__);
|
|
return;
|
|
}
|
|
|
|
/* Set Ethernet LED in TX blink mode */
|
|
miiphy_write(name, phy_adr, PHY_LED_MAN_REG, 0x00);
|
|
miiphy_write(name, phy_adr, PHY_LED_PAR_SEL_REG, PHY_LED_VAL);
|
|
|
|
/* reset the phy */
|
|
miiphy_reset(name, phy_adr);
|
|
debug("88E3015 Initialized on %s\n", name);
|
|
}
|
|
#endif /* CONFIG_RESET_PHY_R */
|
|
#endif /* CONFIG_ARMADA100_FEC */
|
|
|