upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
490 lines
16 KiB
490 lines
16 KiB
/*
|
|
* (C) Copyright 2001
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
|
|
#define CONFIG_ATC 1 /* ...on a ATC board */
|
|
#define CONFIG_CPM2 1 /* Has a CPM2 */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xFF000000
|
|
|
|
/*
|
|
* select serial console configuration
|
|
*
|
|
* if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
|
|
* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
|
|
* for SCC).
|
|
*
|
|
* if CONFIG_CONS_NONE is defined, then the serial console routines must
|
|
* defined elsewhere (for example, on the cogent platform, there are serial
|
|
* ports on the motherboard which are used for the serial console - see
|
|
* cogent/cma101/serial.[ch]).
|
|
*/
|
|
#define CONFIG_CONS_ON_SMC /* define if console on SMC */
|
|
#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
|
|
#undef CONFIG_CONS_NONE /* define if console on something else*/
|
|
#define CONFIG_CONS_INDEX 2 /* which serial channel for console */
|
|
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
/*
|
|
* select ethernet configuration
|
|
*
|
|
* if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
|
|
* CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
|
|
* for FCC)
|
|
*
|
|
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
|
|
* defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
|
|
*/
|
|
#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
|
|
#undef CONFIG_ETHER_NONE /* define if ether on something else */
|
|
#define CONFIG_ETHER_ON_FCC
|
|
|
|
#define CONFIG_ETHER_ON_FCC2
|
|
|
|
/*
|
|
* - Rx-CLK is CLK13
|
|
* - Tx-CLK is CLK14
|
|
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
|
|
* - Enable Full Duplex in FSMR
|
|
*/
|
|
# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
|
|
# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
|
|
# define CONFIG_SYS_CPMFCR_RAMTYPE 0
|
|
# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
|
|
|
|
#define CONFIG_ETHER_ON_FCC3
|
|
|
|
/*
|
|
* - Rx-CLK is CLK15
|
|
* - Tx-CLK is CLK16
|
|
* - RAM for BD/Buffers is on the local Bus (see 28-13)
|
|
* - Enable Half Duplex in FSMR
|
|
*/
|
|
# define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
|
|
# define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
|
|
|
|
/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
|
|
#define CONFIG_8260_CLKIN 64000000 /* in Hz */
|
|
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
|
|
#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in Hz */
|
|
|
|
#define CONFIG_PREBOOT \
|
|
"echo;" \
|
|
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;"\
|
|
"echo"
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"bootp;" \
|
|
"setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"\
|
|
"bootm"
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Miscellaneous configuration options
|
|
*/
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_PCI
|
|
#define CONFIG_CMD_PCMCIA
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_IDE
|
|
|
|
|
|
#define CONFIG_DOS_PARTITION
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
|
|
|
|
#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 /* "bad" address */
|
|
|
|
#define CONFIG_SYS_ALLOC_DPRAM
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
#define CONFIG_SPI
|
|
|
|
#define CONFIG_RTC_DS12887
|
|
|
|
#define RTC_BASE_ADDR 0xF5000000
|
|
#define RTC_PORT_ADDR RTC_BASE_ADDR + 0x800
|
|
#define RTC_PORT_DATA RTC_BASE_ADDR + 0x808
|
|
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Flash configuration
|
|
*/
|
|
|
|
#define CONFIG_SYS_FLASH_BASE 0xFF000000
|
|
#define CONFIG_SYS_FLASH_SIZE 0x00800000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
|
|
|
|
#define CONFIG_FLASH_16BIT
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Hard Reset Configuration Words
|
|
*
|
|
* if you change bits in the HRCW, you must also change the CONFIG_SYS_*
|
|
* defines for the various registers affected by the HRCW e.g. changing
|
|
* HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
|
|
*/
|
|
#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
|
|
HRCW_BPS10 |\
|
|
HRCW_APPC10)
|
|
|
|
/* no slaves so just fill with zeros */
|
|
#define CONFIG_SYS_HRCW_SLAVE1 0
|
|
#define CONFIG_SYS_HRCW_SLAVE2 0
|
|
#define CONFIG_SYS_HRCW_SLAVE3 0
|
|
#define CONFIG_SYS_HRCW_SLAVE4 0
|
|
#define CONFIG_SYS_HRCW_SLAVE5 0
|
|
#define CONFIG_SYS_HRCW_SLAVE6 0
|
|
#define CONFIG_SYS_HRCW_SLAVE7 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Internal Memory Mapped Register
|
|
*/
|
|
#define CONFIG_SYS_IMMR 0xF0000000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*
|
|
* 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE.
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
|
|
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
|
# define CONFIG_SYS_RAMBOOT
|
|
#endif
|
|
|
|
#define CONFIG_PCI
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE
|
|
#define CONFIG_PCI_PNP
|
|
#define CONFIG_SYS_PCI_MSTR_IO_BUS 0x00000000 /* PCI base */
|
|
|
|
#if 1
|
|
/* environment is in Flash */
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x30000)
|
|
# define CONFIG_ENV_SIZE 0x10000
|
|
# define CONFIG_ENV_SECT_SIZE 0x10000
|
|
#else
|
|
#define CONFIG_ENV_IS_IN_EEPROM 1
|
|
#define CONFIG_ENV_OFFSET 0
|
|
#define CONFIG_ENV_SIZE 2048
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* HIDx - Hardware Implementation-dependent Registers 2-11
|
|
*-----------------------------------------------------------------------
|
|
* HID0 also contains cache control - initially enable both caches and
|
|
* invalidate contents, then the final state leaves only the instruction
|
|
* cache enabled. Note that Power-On and Hard reset invalidate the caches,
|
|
* but Soft reset does not.
|
|
*
|
|
* HID1 has only read-only information - nothing to set.
|
|
*/
|
|
#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|\
|
|
HID0_DCI|HID0_IFEM|HID0_ABE)
|
|
#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE)
|
|
#define CONFIG_SYS_HID2 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RMR - Reset Mode Register 5-5
|
|
*-----------------------------------------------------------------------
|
|
* turn on Checkstop Reset Enable
|
|
*/
|
|
#define CONFIG_SYS_RMR RMR_CSRE
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* BCR - Bus Configuration 4-25
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define BCR_APD01 0x10000000
|
|
#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 4-31
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_BBD|SIUMCR_APPC10|\
|
|
SIUMCR_CS10PC00|SIUMCR_BCTLC10)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 4-35
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
|
|
*/
|
|
#if defined(CONFIG_WATCHDOG)
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
|
|
SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
|
|
#else
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
|
|
SYPCR_SWRI|SYPCR_SWP)
|
|
#endif /* CONFIG_WATCHDOG */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TMCNTSC - Time Counter Status and Control 4-40
|
|
*-----------------------------------------------------------------------
|
|
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
|
|
* and enable Time Counter
|
|
*/
|
|
#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 4-42
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
|
|
* Periodic timer
|
|
*/
|
|
#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SCCR - System Clock Control 9-8
|
|
*-----------------------------------------------------------------------
|
|
* Ensure DFBRG is Divide by 16
|
|
*/
|
|
#define CONFIG_SYS_SCCR SCCR_DFBRG01
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RCCR - RISC Controller Configuration 13-7
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_RCCR 0
|
|
|
|
#define CONFIG_SYS_MIN_AM_MASK 0xC0000000
|
|
/*-----------------------------------------------------------------------
|
|
* MPTPR - Memory Refresh Timer Prescaler Register 10-18
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_MPTPR 0x1F00
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PSRT - Refresh Timer Register 10-16
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_PSRT 0x0f
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PSRT - SDRAM Mode Register 10-10
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
/* SDRAM initialization values for 8-column chips
|
|
*/
|
|
#define CONFIG_SYS_OR2_8COL (CONFIG_SYS_MIN_AM_MASK |\
|
|
ORxS_BPD_4 |\
|
|
ORxS_ROWST_PBI1_A7 |\
|
|
ORxS_NUMR_12)
|
|
|
|
#define CONFIG_SYS_PSDMR_8COL (PSDMR_PBI |\
|
|
PSDMR_SDAM_A15_IS_A5 |\
|
|
PSDMR_BSMA_A15_A17 |\
|
|
PSDMR_SDA10_PBI1_A7 |\
|
|
PSDMR_RFRC_7_CLK |\
|
|
PSDMR_PRETOACT_3W |\
|
|
PSDMR_ACTTORW_2W |\
|
|
PSDMR_LDOTOPRE_1C |\
|
|
PSDMR_WRC_1C |\
|
|
PSDMR_CL_2)
|
|
|
|
/* SDRAM initialization values for 9-column chips
|
|
*/
|
|
#define CONFIG_SYS_OR2_9COL (CONFIG_SYS_MIN_AM_MASK |\
|
|
ORxS_BPD_4 |\
|
|
ORxS_ROWST_PBI1_A6 |\
|
|
ORxS_NUMR_12)
|
|
|
|
#define CONFIG_SYS_PSDMR_9COL (PSDMR_PBI |\
|
|
PSDMR_SDAM_A16_IS_A5 |\
|
|
PSDMR_BSMA_A15_A17 |\
|
|
PSDMR_SDA10_PBI1_A6 |\
|
|
PSDMR_RFRC_7_CLK |\
|
|
PSDMR_PRETOACT_3W |\
|
|
PSDMR_ACTTORW_2W |\
|
|
PSDMR_LDOTOPRE_1C |\
|
|
PSDMR_WRC_1C |\
|
|
PSDMR_CL_2)
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* Bank Bus Machine PortSz Device
|
|
* ---- --- ------- ------ ------
|
|
* 0 60x GPCM 8 bit Boot ROM
|
|
* 1 60x GPCM 64 bit FLASH
|
|
* 2 60x SDRAM 64 bit SDRAM
|
|
*
|
|
*/
|
|
|
|
#define CONFIG_SYS_MRS_OFFS 0x00000000
|
|
|
|
/* Bank 0 - FLASH
|
|
*/
|
|
#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_16 |\
|
|
BRx_MS_GPCM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
|
|
ORxG_CSNT |\
|
|
ORxG_ACS_DIV1 |\
|
|
ORxG_SCY_3_CLK |\
|
|
ORxU_EHTR_8IDLE)
|
|
|
|
|
|
/* Bank 2 - 60x bus SDRAM
|
|
*/
|
|
#ifndef CONFIG_SYS_RAMBOOT
|
|
#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_64 |\
|
|
BRx_MS_SDRAM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_8COL
|
|
|
|
#define CONFIG_SYS_PSDMR CONFIG_SYS_PSDMR_8COL
|
|
#endif /* CONFIG_SYS_RAMBOOT */
|
|
|
|
#define CONFIG_SYS_BR4_PRELIM ((RTC_BASE_ADDR & BRx_BA_MSK) |\
|
|
BRx_PS_8 |\
|
|
BRx_MS_UPMA |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR4_PRELIM (ORxU_AM_MSK | ORxU_BI)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCMCIA stuff
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
#define CONFIG_I82365
|
|
|
|
#define CONFIG_SYS_PCMCIA_MEM_ADDR 0x81000000
|
|
#define CONFIG_SYS_PCMCIA_MEM_SIZE 0x1000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
|
|
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
|
|
|
|
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
|
|
#undef CONFIG_IDE_LED /* LED for ide not supported */
|
|
#undef CONFIG_IDE_RESET /* reset for ide not supported */
|
|
|
|
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
|
|
#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
|
|
|
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
|
|
|
#define CONFIG_SYS_ATA_BASE_ADDR 0xa0000000
|
|
|
|
/* Offset for data I/O */
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET 0x100
|
|
|
|
/* Offset for normal register accesses */
|
|
#define CONFIG_SYS_ATA_REG_OFFSET 0x100
|
|
|
|
/* Offset for alternate registers */
|
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x108
|
|
|
|
#endif /* __CONFIG_H */
|
|
|