upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/include/configs/cm_t3517.h

231 lines
6.4 KiB

/*
* (C) Copyright 2013 CompuLab, Ltd.
* Author: Igor Grinberg <grinberg@compulab.co.il>
*
* Configuration settings for the CompuLab CM-T3517 board
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_CM_T3517 /* working with CM-T3517 */
/*
* This is needed for the DMA stuff.
* Although the default iss 64, we still define it
* to be on the safe side once the default is changed.
*/
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap.h>
#define CONFIG_MACH_TYPE MACH_TYPE_CM_T3517
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
#define CONFIG_MISC_INIT_R
/*
* The early kernel mapping on ARM currently only maps from the base of DRAM
* to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000.
* The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000,
* so that leaves DRAM base to DRAM base + 0x4000 available.
*/
#define CONFIG_SYS_BOOTMAPSZ 0x4000
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SERIAL_TAG
/*
* Size of malloc() pool
*/
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
/*
* Hardware drivers
*/
/*
* NS16550 Configuration
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
/*
* select serial console configuration
*/
#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
#define CONFIG_SERIAL3 3 /* UART3 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
/* USB */
#ifndef CONFIG_USB_MUSB_AM35X
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 146
#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 147
#endif /* CONFIG_USB_MUSB_AM35X */
/* commands to include */
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_MTD_PARTITIONS
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_I2C_EEPROM_BUS 0
#define CONFIG_I2C_MULTI_BUS
/*
* Board NAND Info.
*/
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
/* Environment information */
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
"baudrate=115200\0" \
"console=ttyO2,115200n8\0" \
"netretry=yes\0" \
"mpurate=auto\0" \
"vram=12M\0" \
"dvimode=1024x768MR-16@60\0" \
"defaultdisplay=dvi\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
"mmcrootfstype=ext4\0" \
"nandroot=/dev/mtdblock4 rw\0" \
"nandrootfstype=ubifs\0" \
"mmcargs=setenv bootargs console=${console} " \
"mpurate=${mpurate} " \
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
"omapdss.def_disp=${defaultdisplay} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
"nandargs=setenv bootargs console=${console} " \
"mpurate=${mpurate} " \
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
"omapdss.def_disp=${defaultdisplay} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source ${loadaddr}\0" \
"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
"nand read ${loadaddr} 2a0000 400000; " \
"bootm ${loadaddr}\0" \
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"if run loaduimage; then " \
"run mmcboot; " \
"else run nandboot; " \
"fi; " \
"fi; " \
"else run nandboot; fi"
/*
* Miscellaneous configurable options
*/
#define CONFIG_TIMESTAMP
#define CONFIG_SYS_AUTOLOAD "no"
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000)
/*
* AM3517 has 12 GP timers, they can be driven by the system clock
* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
* This rate is divided by a local divisor.
*/
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
#define CONFIG_SYS_HZ 1000
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1 /* CM-T3517 DRAM is only on CS0 */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
#define CONFIG_SYS_CS0_SIZE (256 << 20)
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
/* **** PISMO SUPPORT *** */
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_ENV_OFFSET 0x260000
#define CONFIG_ENV_ADDR 0x260000
#if defined(CONFIG_CMD_NET)
#define CONFIG_DRIVER_TI_EMAC
#define CONFIG_DRIVER_TI_EMAC_USE_RMII
#define CONFIG_MII
#define CONFIG_ARP_TIMEOUT 200UL
#define CONFIG_NET_RETRY_COUNT 5
#endif /* CONFIG_CMD_NET */
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
/* Status LED */
#define GREEN_LED_GPIO 186 /* CM-T3517 Green LED is GPIO186 */
/* Display Configuration */
#define CONFIG_VIDEO_OMAP3
#define LCD_BPP LCD_COLOR16
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASHIMAGE_GUARD
#define CONFIG_BMP_16BPP
#define CONFIG_SCF0403_LCD
/* EEPROM */
#define CONFIG_ENV_EEPROM_IS_ON_I2C
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
#define CONFIG_SYS_EEPROM_SIZE 256
#endif /* __CONFIG_H */