upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/LEOX/elpt860/elpt860.c

348 lines
10 KiB

/*
**=====================================================================
**
** Copyright (C) 2000, 2001, 2002, 2003
** The LEOX team <team@leox.org>, http://www.leox.org
**
** LEOX.org is about the development of free hardware and software resources
** for system on chip.
**
** Description: U-Boot port on the LEOX's ELPT860 CPU board
** ~~~~~~~~~~~
**
**=====================================================================
**
** This program is free software; you can redistribute it and/or
** modify it under the terms of the GNU General Public License as
** published by the Free Software Foundation; either version 2 of
** the License, or (at your option) any later version.
**
** This program is distributed in the hope that it will be useful,
** but WITHOUT ANY WARRANTY; without even the implied warranty of
** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
** GNU General Public License for more details.
**
** You should have received a copy of the GNU General Public License
** along with this program; if not, write to the Free Software
** Foundation, Inc., 59 Temple Place, Suite 330, Boston,
** MA 02111-1307 USA
**
**=====================================================================
*/
/*
** Note 1: In this file, you have to provide the following functions:
** ------
** int board_early_init_f(void)
** int checkboard(void)
** phys_size_t initdram(int board_type)
** called from 'board_init_f()' into 'common/board.c'
**
** void reset_phy(void)
** called from 'board_init_r()' into 'common/board.c'
*/
#include <common.h>
#include <mpc8xx.h>
/* ------------------------------------------------------------------------- */
static long int dram_size (long int, long int *, long int);
/* ------------------------------------------------------------------------- */
#define _NOT_USED_ 0xFFFFFFFF
const uint init_sdram_table[] = {
/*
* Single Read. (Offset 0 in UPMA RAM)
*/
0x0FFCCC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04,
0xFFFFFC04, /* last */
/*
* SDRAM Initialization (offset 5 in UPMA RAM)
*
* This is no UPM entry point. The following definition uses
* the remaining space to establish an initialization
* sequence, which is executed by a RUN command.
*
*/
0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, /* last */
/*
* Burst Read. (Offset 8 in UPMA RAM)
*/
0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04,
0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, /* last */
/*
* Single Write. (Offset 18 in UPMA RAM)
*/
0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04,
0xFFFFFC04, 0xFFFFFC04, 0x0FFFFC04, 0xFFFFFC04, /* last */
/*
* Burst Write. (Offset 20 in UPMA RAM)
*/
0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04,
0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC34, 0x0FAC0C34,
0xFFFFFC05, 0xFFFFFC04, 0x0FFCFC04, 0xFFFFFC05, /* last */
};
const uint sdram_table[] = {
/*
* Single Read. (Offset 0 in UPMA RAM)
*/
0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04,
0xFF0FFC00, /* last */
/*
* SDRAM Initialization (offset 5 in UPMA RAM)
*
* This is no UPM entry point. The following definition uses
* the remaining space to establish an initialization
* sequence, which is executed by a RUN command.
*
*/
0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC05, /* last */
/*
* Burst Read. (Offset 8 in UPMA RAM)
*/
0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04,
0xF00FFC00, 0xF00FFC00, 0xF00FFC00, 0xFF0FFC00,
0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04,
0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */
/*
* Single Write. (Offset 18 in UPMA RAM)
*/
0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF0C00,
0xFF0FFC04, 0x0FFCCC04, 0xFFAFFC05, /* last */
_NOT_USED_,
/*
* Burst Write. (Offset 20 in UPMA RAM)
*/
0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC00, 0x00AF0C00,
0xF00FFC00, 0xF00FFC00, 0xF00FFC04, 0x0FFCCC04,
0xFFAFFC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04,
0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */
/*
* Refresh (Offset 30 in UPMA RAM)
*/
0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
0xFFFFFC05, 0xFFFFFC04, 0xFFFFFC05, _NOT_USED_,
0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */
/*
* Exception. (Offset 3c in UPMA RAM)
*/
0x0FFFFC34, 0x0FAC0C34, 0xFFFFFC05, 0xFFAFFC04, /* last */
};
/* ------------------------------------------------------------------------- */
#define CONFIG_SYS_PC4 0x0800
#define CONFIG_SYS_DS1 CONFIG_SYS_PC4
/*
* Very early board init code (fpga boot, etc.)
*/
int board_early_init_f (void)
{
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
/*
* Light up the red led on ELPT860 pcb (DS1) (PCDAT)
*/
immr->im_ioport.iop_pcdat &= ~CONFIG_SYS_DS1; /* PCDAT (DS1 = 0) */
immr->im_ioport.iop_pcpar &= ~CONFIG_SYS_DS1; /* PCPAR (0=general purpose I/O) */
immr->im_ioport.iop_pcdir |= CONFIG_SYS_DS1; /* PCDIR (I/O: 0=input, 1=output) */
return (0); /* success */
}
/*
* Check Board Identity:
*
* Test ELPT860 ID string
*
* Return 1 if no second DRAM bank, otherwise returns 0
*/
int checkboard (void)
{
char *s = getenv ("serial#");
if (!s || strncmp (s, "ELPT860", 7))
printf ("### No HW ID - assuming ELPT860\n");
return (0); /* success */
}
/* ------------------------------------------------------------------------- */
phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size8, size9;
long int size_b0 = 0;
/*
* This sequence initializes SDRAM chips on ELPT860 board
*/
upmconfig (UPMA, (uint *) init_sdram_table,
sizeof (init_sdram_table) / sizeof (uint));
memctl->memc_mptpr = 0x0200;
memctl->memc_mamr = 0x18002111;
memctl->memc_mar = 0x00000088;
memctl->memc_mcr = 0x80002000; /* CS1: SDRAM bank 0 */
upmconfig (UPMA, (uint *) sdram_table,
sizeof (sdram_table) / sizeof (uint));
/*
* Preliminary prescaler for refresh (depends on number of
* banks): This value is selected for four cycles every 62.4 us
* with two SDRAM banks or four cycles every 31.2 us with one
* bank. It will be adjusted after memory sizing.
*/
memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
/*
* The following value is used as an address (i.e. opcode) for
* the LOAD MODE REGISTER COMMAND during SDRAM initialisation. If
* the port size is 32bit the SDRAM does NOT "see" the lower two
* address lines, i.e. mar=0x00000088 -> opcode=0x00000022 for
* MICRON SDRAMs:
* -> 0 00 010 0 010
* | | | | +- Burst Length = 4
* | | | +----- Burst Type = Sequential
* | | +------- CAS Latency = 2
* | +----------- Operating Mode = Standard
* +-------------- Write Burst Mode = Programmed Burst Length
*/
memctl->memc_mar = 0x00000088;
/*
* Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at
* preliminary addresses - these have to be modified after the
* SDRAM size has been determined.
*/
memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
udelay (200);
/* perform SDRAM initializsation sequence */
memctl->memc_mcr = 0x80002105; /* CS1: SDRAM bank 0 */
udelay (1);
memctl->memc_mcr = 0x80002230; /* CS1: SDRAM bank 0 - execute twice */
udelay (1);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay (1000);
/*
* Check Bank 0 Memory Size for re-configuration
*
* try 8 column mode
*/
size8 = dram_size (CONFIG_SYS_MAMR_8COL,
SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE);
udelay (1000);
/*
* try 9 column mode
*/
size9 = dram_size (CONFIG_SYS_MAMR_9COL,
SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
size_b0 = size9;
/* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
} else { /* back to 8 columns */
size_b0 = size8;
memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
udelay (500);
/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
}
udelay (1000);
/*
* Adjust refresh rate depending on SDRAM type, both banks
* For types > 128 MBit leave it at the current (fast) rate
*/
if (size_b0 < 0x02000000) {
/* reduce to 15.6 us (62.4 us / quad) */
memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
udelay (1000);
}
/*
* Final mapping: map bigger bank first
*/
memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
{
unsigned long reg;
/* adjust refresh rate depending on SDRAM type, one bank */
reg = memctl->memc_mptpr;
reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
memctl->memc_mptpr = reg;
}
udelay (10000);
return (size_b0);
}
/* ------------------------------------------------------------------------- */
/*
* Check memory range for valid RAM. A simple memory test determines
* the actually available RAM size between addresses `base' and
* `base + maxsize'. Some (not all) hardware errors are detected:
* - short between address lines
* - short between data lines
*/
static long int
dram_size (long int mamr_value, long int *base, long int maxsize)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
memctl->memc_mamr = mamr_value;
return (get_ram_size (base, maxsize));
}
/* ------------------------------------------------------------------------- */
#define CONFIG_SYS_PA1 0x4000
#define CONFIG_SYS_PA2 0x2000
#define CONFIG_SYS_LBKs (CONFIG_SYS_PA2 | CONFIG_SYS_PA1)
void reset_phy (void)
{
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
/*
* Ensure LBK LXT901 ethernet 1 & 2 = 0 ... for normal loopback in effect
* and no AUI loopback
*/
immr->im_ioport.iop_padat &= ~CONFIG_SYS_LBKs; /* PADAT (LBK eth 1&2 = 0) */
immr->im_ioport.iop_papar &= ~CONFIG_SYS_LBKs; /* PAPAR (0=general purpose I/O) */
immr->im_ioport.iop_padir |= CONFIG_SYS_LBKs; /* PADIR (I/O: 0=input, 1=output) */
}