upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
582 lines
20 KiB
582 lines
20 KiB
/*
|
|
* (C) Copyright 2001-2011
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* Modified during 2001 by
|
|
* Advanced Communications Technologies (Australia) Pty. Ltd.
|
|
* Howard Walker, Tuong Vu-Dinh
|
|
*
|
|
* (C) Copyright 2001, Stuart Hughes, Lineo Inc, stuarth@lineo.com
|
|
* Added support for the 16M dram simm on the 8260ads boards
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <ioports.h>
|
|
#include <i2c.h>
|
|
#include <mpc8260.h>
|
|
#include <pci.h>
|
|
|
|
/*
|
|
* PBI Page Based Interleaving
|
|
* PSDMR_PBI page based interleaving
|
|
* 0 bank based interleaving
|
|
* External Address Multiplexing (EAMUX) adds a clock to address cycles
|
|
* (this can help with marginal board layouts)
|
|
* PSDMR_EAMUX adds a clock
|
|
* 0 no extra clock
|
|
* Buffer Command (BUFCMD) adds a clock to command cycles.
|
|
* PSDMR_BUFCMD adds a clock
|
|
* 0 no extra clock
|
|
*/
|
|
#define CONFIG_PBI 0
|
|
#define PESSIMISTIC_SDRAM 0
|
|
#define EAMUX 0 /* EST requires EAMUX */
|
|
#define BUFCMD 0
|
|
|
|
|
|
/*
|
|
* I/O Port configuration table
|
|
*
|
|
* if conf is 1, then that port pin will be configured at boot time
|
|
* according to the five values podr/pdir/ppar/psor/pdat for that entry
|
|
*/
|
|
|
|
const iop_conf_t iop_conf_tab[4][32] = {
|
|
|
|
/* Port A configuration */
|
|
{ /* conf ppar psor pdir podr pdat */
|
|
/* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */
|
|
/* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */
|
|
/* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */
|
|
/* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */
|
|
/* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */
|
|
/* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */
|
|
/* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */
|
|
/* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */
|
|
/* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */
|
|
/* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */
|
|
/* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */
|
|
/* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */
|
|
/* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */
|
|
/* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */
|
|
/* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
|
|
/* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
|
|
/* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
|
|
/* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
|
|
/* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
|
|
/* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
|
|
/* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
|
|
/* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */
|
|
/* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */
|
|
/* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */
|
|
/* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */
|
|
/* PA6 */ { 1, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */
|
|
/* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */
|
|
/* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */
|
|
/* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */
|
|
/* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */
|
|
/* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FREERUN */
|
|
/* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */
|
|
},
|
|
|
|
/* Port B configuration */
|
|
{ /* conf ppar psor pdir podr pdat */
|
|
/* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
|
|
/* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
|
|
/* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
|
|
/* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
|
|
/* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
|
|
/* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
|
|
/* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
|
|
/* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
|
|
/* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
|
|
/* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
|
|
/* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
|
|
/* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
|
|
/* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
|
|
/* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
|
|
/* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
|
|
/* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
|
|
/* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
|
|
/* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */
|
|
/* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */
|
|
/* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */
|
|
/* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
|
|
/* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
|
|
/* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
|
|
/* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
|
|
/* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
|
|
/* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
|
|
/* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
|
|
/* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
|
|
/* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
|
|
/* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
|
|
/* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
|
|
/* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
|
|
},
|
|
|
|
/* Port C */
|
|
{ /* conf ppar psor pdir podr pdat */
|
|
/* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */
|
|
/* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */
|
|
/* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */
|
|
/* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */
|
|
/* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */
|
|
/* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */
|
|
/* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */
|
|
/* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */
|
|
/* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */
|
|
/* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */
|
|
/* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
|
|
/* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
|
|
/* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */
|
|
/* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */
|
|
/* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */
|
|
/* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */
|
|
/* PC15 */ { 0, 0, 0, 1, 0, 0 }, /* PC15 */
|
|
/* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */
|
|
/* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */
|
|
/* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */
|
|
/* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */
|
|
/* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* LXT970 FETHMDC */
|
|
/* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* LXT970 FETHMDIO */
|
|
/* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */
|
|
/* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */
|
|
/* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */
|
|
/* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */
|
|
/* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */
|
|
/* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */
|
|
/* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */
|
|
/* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */
|
|
/* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */
|
|
},
|
|
|
|
/* Port D */
|
|
{ /* conf ppar psor pdir podr pdat */
|
|
/* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */
|
|
/* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */
|
|
/* PD29 */ { 0, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */
|
|
/* PD28 */ { 0, 1, 0, 0, 0, 0 }, /* PD28 */
|
|
/* PD27 */ { 0, 1, 1, 1, 0, 0 }, /* PD27 */
|
|
/* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */
|
|
/* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */
|
|
/* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */
|
|
/* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */
|
|
/* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */
|
|
/* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */
|
|
/* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */
|
|
/* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */
|
|
/* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */
|
|
/* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */
|
|
/* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */
|
|
/* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */
|
|
/* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */
|
|
/* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
|
|
/* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
|
|
/* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
|
|
/* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
|
|
/* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
|
|
/* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
|
|
/* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */
|
|
/* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */
|
|
/* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */
|
|
/* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */
|
|
/* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
|
|
/* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
|
|
/* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
|
|
/* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
|
|
}
|
|
};
|
|
|
|
typedef struct bscr_ {
|
|
unsigned long bcsr0;
|
|
unsigned long bcsr1;
|
|
unsigned long bcsr2;
|
|
unsigned long bcsr3;
|
|
unsigned long bcsr4;
|
|
unsigned long bcsr5;
|
|
unsigned long bcsr6;
|
|
unsigned long bcsr7;
|
|
} bcsr_t;
|
|
|
|
typedef struct pci_ic_s {
|
|
unsigned long pci_int_stat;
|
|
unsigned long pci_int_mask;
|
|
} pci_ic_t;
|
|
|
|
void reset_phy(void)
|
|
{
|
|
volatile bcsr_t *bcsr = (bcsr_t *)CONFIG_SYS_BCSR;
|
|
|
|
/* reset the FEC port */
|
|
bcsr->bcsr1 &= ~FETH_RST;
|
|
bcsr->bcsr1 |= FETH_RST;
|
|
}
|
|
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
volatile bcsr_t *bcsr = (bcsr_t *)CONFIG_SYS_BCSR;
|
|
volatile pci_ic_t *pci_ic = (pci_ic_t *)CONFIG_SYS_PCI_INT;
|
|
|
|
bcsr->bcsr1 = ~FETHIEN & ~RS232EN_1 & ~RS232EN_2;
|
|
|
|
/* mask all PCI interrupts */
|
|
pci_ic->pci_int_mask |= 0xfff00000;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
puts("Board: Motorola MPC8266ADS\n");
|
|
return 0;
|
|
}
|
|
|
|
phys_size_t initdram(int board_type)
|
|
{
|
|
/* Autoinit part stolen from board/sacsng/sacsng.c */
|
|
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
|
|
volatile memctl8260_t *memctl = &immap->im_memctl;
|
|
volatile uchar c = 0xff;
|
|
volatile uchar *ramaddr = (uchar *) (CONFIG_SYS_SDRAM_BASE + 0x8);
|
|
uint psdmr = CONFIG_SYS_PSDMR;
|
|
int i;
|
|
|
|
uint psrt = 0x21; /* for no SPD */
|
|
uint chipselects = 1; /* for no SPD */
|
|
uint sdram_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; /* for no SPD */
|
|
uint or = CONFIG_SYS_OR2_PRELIM; /* for no SPD */
|
|
uint data_width;
|
|
uint rows;
|
|
uint banks;
|
|
uint cols;
|
|
uint caslatency;
|
|
uint width;
|
|
uint rowst;
|
|
uint sdam;
|
|
uint bsma;
|
|
uint sda10;
|
|
u_char data;
|
|
u_char cksum;
|
|
int j;
|
|
|
|
/*
|
|
* Keep the compiler from complaining about
|
|
* potentially uninitialized vars
|
|
*/
|
|
data_width = rows = banks = cols = caslatency = 0;
|
|
|
|
/*
|
|
* Read the SDRAM SPD EEPROM via I2C.
|
|
*/
|
|
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
|
|
|
|
i2c_read(SDRAM_SPD_ADDR, 0, 1, &data, 1);
|
|
cksum = data;
|
|
for (j = 1; j < 64; j++) { /* read only the checksummed bytes */
|
|
/* note: the I2C address autoincrements when alen == 0 */
|
|
i2c_read(SDRAM_SPD_ADDR, 0, 0, &data, 1);
|
|
/*printf("addr %d = 0x%02x\n", j, data); */
|
|
if (j == 5)
|
|
chipselects = data & 0x0F;
|
|
else if (j == 6)
|
|
data_width = data;
|
|
else if (j == 7)
|
|
data_width |= data << 8;
|
|
else if (j == 3)
|
|
rows = data & 0x0F;
|
|
else if (j == 4)
|
|
cols = data & 0x0F;
|
|
else if (j == 12) {
|
|
/*
|
|
* Refresh rate: this assumes the prescaler is set to
|
|
* approximately 0.39uSec per tick and the target
|
|
* refresh period is about 85% of maximum.
|
|
*/
|
|
switch (data & 0x7F) {
|
|
default:
|
|
case 0:
|
|
psrt = 0x21; /* 15.625uS */
|
|
break;
|
|
case 1:
|
|
psrt = 0x07; /* 3.9uS */
|
|
break;
|
|
case 2:
|
|
psrt = 0x0F; /* 7.8uS */
|
|
break;
|
|
case 3:
|
|
psrt = 0x43; /* 31.3uS */
|
|
break;
|
|
case 4:
|
|
psrt = 0x87; /* 62.5uS */
|
|
break;
|
|
case 5:
|
|
psrt = 0xFF; /* 125uS */
|
|
break;
|
|
}
|
|
} else if (j == 17)
|
|
banks = data;
|
|
else if (j == 18) {
|
|
caslatency = 3; /* default CL */
|
|
#if (PESSIMISTIC_SDRAM)
|
|
if ((data & 0x04) != 0)
|
|
caslatency = 3;
|
|
else if ((data & 0x02) != 0)
|
|
caslatency = 2;
|
|
else if ((data & 0x01) != 0)
|
|
caslatency = 1;
|
|
#else
|
|
if ((data & 0x01) != 0)
|
|
caslatency = 1;
|
|
else if ((data & 0x02) != 0)
|
|
caslatency = 2;
|
|
else if ((data & 0x04) != 0)
|
|
caslatency = 3;
|
|
#endif
|
|
else {
|
|
printf("WARNING: Unknown CAS latency 0x%02X, using 3\n",
|
|
data);
|
|
}
|
|
} else if (j == 63) {
|
|
if (data != cksum) {
|
|
printf("WARNING: Configuration data checksum failure:"
|
|
" is 0x%02x, calculated 0x%02x\n",
|
|
data, cksum);
|
|
}
|
|
}
|
|
cksum += data;
|
|
}
|
|
|
|
/* We don't trust CL less than 2 (only saw it on an old 16MByte DIMM) */
|
|
if (caslatency < 2) {
|
|
printf("CL was %d, forcing to 2\n", caslatency);
|
|
caslatency = 2;
|
|
}
|
|
if (rows > 14) {
|
|
printf("This doesn't look good, rows = %d, should be <= 14\n",
|
|
rows);
|
|
rows = 14;
|
|
}
|
|
if (cols > 11) {
|
|
printf("This doesn't look good, columns = %d, should be <= 11\n",
|
|
cols);
|
|
cols = 11;
|
|
}
|
|
|
|
if ((data_width != 64) && (data_width != 72)) {
|
|
printf("WARNING: SDRAM width unsupported, is %d, expected 64 or 72.\n",
|
|
data_width);
|
|
}
|
|
width = 3; /* 2^3 = 8 bytes = 64 bits wide */
|
|
/*
|
|
* Convert banks into log2(banks)
|
|
*/
|
|
if (banks == 2)
|
|
banks = 1;
|
|
else if (banks == 4)
|
|
banks = 2;
|
|
else if (banks == 8)
|
|
banks = 3;
|
|
|
|
|
|
sdram_size = 1 << (rows + cols + banks + width);
|
|
/* hack for high density memory (512MB per CS) */
|
|
/* !!!!! Will ONLY work with Page Based Interleave !!!!!
|
|
( PSDMR[PBI] = 1 )
|
|
*/
|
|
/*
|
|
* memory actually has 11 column addresses, but the memory
|
|
* controller doesn't really care.
|
|
*
|
|
* the calculations that follow will however move the rows so
|
|
* that they are muxed one bit off if you use 11 bit columns.
|
|
*
|
|
* The solution is to tell the memory controller the correct
|
|
* size of the memory but change the number of columns to 10
|
|
* afterwards.
|
|
*
|
|
* The 11th column addre will still be mucxed correctly onto
|
|
* the bus.
|
|
*
|
|
* Also be aware that the MPC8266ADS board Rev B has not
|
|
* connected Row address 13 to anything.
|
|
*
|
|
* The fix is to connect ADD16 (from U37-47) to SADDR12 (U28-126)
|
|
*/
|
|
if (cols > 10)
|
|
cols = 10;
|
|
|
|
#if (CONFIG_PBI == 0) /* bank-based interleaving */
|
|
rowst = ((32 - 6) - (rows + cols + width)) * 2;
|
|
#else
|
|
rowst = 32 - (rows + banks + cols + width);
|
|
#endif
|
|
|
|
or = ~(sdram_size - 1) | /* SDAM address mask */
|
|
((banks - 1) << 13) | /* banks per device */
|
|
(rowst << 9) | /* rowst */
|
|
((rows - 9) << 6); /* numr */
|
|
|
|
|
|
/*printf("memctl->memc_or2 = 0x%08x\n", or); */
|
|
|
|
/*
|
|
* SDAM specifies the number of columns that are multiplexed
|
|
* (reference AN2165/D), defined to be (columns - 6) for page
|
|
* interleave, (columns - 8) for bank interleave.
|
|
*
|
|
* BSMA is 14 - max(rows, cols). The bank select lines come
|
|
* into play above the highest "address" line going into the
|
|
* the SDRAM.
|
|
*/
|
|
#if (CONFIG_PBI == 0) /* bank-based interleaving */
|
|
sdam = cols - 8;
|
|
bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols);
|
|
sda10 = sdam + 2;
|
|
#else
|
|
sdam = cols + banks - 8;
|
|
bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols);
|
|
sda10 = sdam;
|
|
#endif
|
|
#if (PESSIMISTIC_SDRAM)
|
|
psdmr = (CONFIG_PBI | PSDMR_RFEN | PSDMR_RFRC_16_CLK |
|
|
PSDMR_PRETOACT_8W | PSDMR_ACTTORW_8W | PSDMR_WRC_4C |
|
|
PSDMR_EAMUX | PSDMR_BUFCMD) | caslatency |
|
|
((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */
|
|
(sdam << 24) | (bsma << 21) | (sda10 << 18);
|
|
#else
|
|
psdmr = (CONFIG_PBI | PSDMR_RFEN | PSDMR_RFRC_7_CLK |
|
|
PSDMR_PRETOACT_3W | /* 1 for 7E parts (fast PC-133) */
|
|
PSDMR_ACTTORW_2W | /* 1 for 7E parts (fast PC-133) */
|
|
PSDMR_WRC_1C | /* 1 clock + 7nSec */
|
|
EAMUX | BUFCMD) | caslatency |
|
|
((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */
|
|
(sdam << 24) | (bsma << 21) | (sda10 << 18);
|
|
#endif
|
|
/*printf("psdmr = 0x%08x\n", psdmr); */
|
|
|
|
/*
|
|
* Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
|
|
*
|
|
* "At system reset, initialization software must set up the
|
|
* programmable parameters in the memory controller banks registers
|
|
* (ORx, BRx, P/LSDMR). After all memory parameters are configured,
|
|
* system software should execute the following initialization sequence
|
|
* for each SDRAM device.
|
|
*
|
|
* 1. Issue a PRECHARGE-ALL-BANKS command
|
|
* 2. Issue eight CBR REFRESH commands
|
|
* 3. Issue a MODE-SET command to initialize the mode register
|
|
*
|
|
* Quote from Micron MT48LC8M16A2 data sheet:
|
|
*
|
|
* "...the SDRAM requires a 100uS delay prior to issuing any
|
|
* command other than a COMMAND INHIBIT or NOP. Starting at some
|
|
* point during this 100uS period and continuing at least through
|
|
* the end of this period, COMMAND INHIBIT or NOP commands should
|
|
* be applied."
|
|
*
|
|
* "Once the 100uS delay has been satisfied with at least one COMMAND
|
|
* INHIBIT or NOP command having been applied, a /PRECHARGE command/
|
|
* should be applied. All banks must then be precharged, thereby
|
|
* placing the device in the all banks idle state."
|
|
*
|
|
* "Once in the idle state, /two/ AUTO REFRESH cycles must be
|
|
* performed. After the AUTO REFRESH cycles are complete, the
|
|
* SDRAM is ready for mode register programming."
|
|
*
|
|
* (/emphasis/ mine, gvb)
|
|
*
|
|
* The way I interpret this, Micron start up sequence is:
|
|
* 1. Issue a PRECHARGE-BANK command (initial precharge)
|
|
* 2. Issue a PRECHARGE-ALL-BANKS command ("all banks ... precharged")
|
|
* 3. Issue two (presumably, doing eight is OK) CBR REFRESH commands
|
|
* 4. Issue a MODE-SET command to initialize the mode register
|
|
*
|
|
* --------
|
|
*
|
|
* The initial commands are executed by setting P/LSDMR[OP] and
|
|
* accessing the SDRAM with a single-byte transaction."
|
|
*
|
|
* The appropriate BRx/ORx registers have already been set
|
|
* when we get here. The SDRAM can be accessed at the address
|
|
* CONFIG_SYS_SDRAM_BASE.
|
|
*/
|
|
|
|
memctl->memc_mptpr = CONFIG_SYS_MPTPR;
|
|
memctl->memc_psrt = psrt;
|
|
|
|
memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM;
|
|
memctl->memc_or2 = or;
|
|
|
|
memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
|
|
*ramaddr = c;
|
|
|
|
memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
|
|
for (i = 0; i < 8; i++)
|
|
*ramaddr = c;
|
|
|
|
memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
|
|
*ramaddr = c;
|
|
|
|
memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
|
|
*ramaddr = c;
|
|
|
|
/*
|
|
* Do it a second time for the second set of chips if the DIMM has
|
|
* two chip selects (double sided).
|
|
*/
|
|
if (chipselects > 1) {
|
|
ramaddr += sdram_size;
|
|
|
|
memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM + sdram_size;
|
|
memctl->memc_or3 = or;
|
|
|
|
memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
|
|
*ramaddr = c;
|
|
|
|
memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
|
|
for (i = 0; i < 8; i++)
|
|
*ramaddr = c;
|
|
|
|
memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
|
|
*ramaddr = c;
|
|
|
|
memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
|
|
*ramaddr = c;
|
|
}
|
|
|
|
/* print info */
|
|
printf("SDRAM configuration read from SPD\n");
|
|
printf("\tSize per side = %dMB\n", sdram_size >> 20);
|
|
printf("\tOrganization: %d sides, %d banks, %d Columns, %d Rows, Data width = %d bits\n",
|
|
chipselects, 1 << (banks), cols, rows, data_width);
|
|
printf("\tRefresh rate = %d, CAS latency = %d", psrt, caslatency);
|
|
#if (CONFIG_PBI == 0) /* bank-based interleaving */
|
|
printf(", Using Bank Based Interleave\n");
|
|
#else
|
|
printf(", Using Page Based Interleave\n");
|
|
#endif
|
|
printf("\tTotal size: ");
|
|
|
|
/* this delay only needed for original 16MB DIMM...
|
|
* Not needed for any other memory configuration */
|
|
if ((sdram_size * chipselects) == (16 * 1024 * 1024))
|
|
udelay(250000);
|
|
|
|
return sdram_size * chipselects;
|
|
}
|
|
|
|
#ifdef CONFIG_PCI
|
|
struct pci_controller hose;
|
|
|
|
extern void pci_mpc8250_init(struct pci_controller *);
|
|
|
|
void pci_init_board(void)
|
|
{
|
|
pci_mpc8250_init(&hose);
|
|
}
|
|
#endif
|
|
|