upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
595 lines
18 KiB
595 lines
18 KiB
/*
|
|
* Copyright (C) 2005 Sandburst Corporation
|
|
* Travis B. Sawyer
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <config.h>
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include "karef.h"
|
|
#include "karef_version.h"
|
|
#include <timestamp.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/io.h>
|
|
#include <spd_sdram.h>
|
|
#include <i2c.h>
|
|
#include "../common/sb_common.h"
|
|
#if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) || \
|
|
defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3)
|
|
#include <net.h>
|
|
#endif
|
|
|
|
void fpga_init (void);
|
|
|
|
KAREF_BOARD_ID_ST board_id_as[] =
|
|
{
|
|
{"Undefined"}, /* Not specified */
|
|
{"Kamino Reference Design"},
|
|
{"Reserved"}, /* Reserved for future use */
|
|
{"Reserved"}, /* Reserved for future use */
|
|
};
|
|
|
|
KAREF_BOARD_ID_ST ofem_board_id_as[] =
|
|
{
|
|
{"Undefined"},
|
|
{"1x10 + 10x2"},
|
|
{"Reserved"},
|
|
{"Reserved"},
|
|
};
|
|
|
|
/*************************************************************************
|
|
* board_early_init_f
|
|
*
|
|
* Setup chip selects, initialize the Opto-FPGA, initialize
|
|
* interrupt polarity and triggers.
|
|
************************************************************************/
|
|
int board_early_init_f (void)
|
|
{
|
|
ppc440_gpio_regs_t *gpio_regs;
|
|
|
|
/* Enable GPIO interrupts */
|
|
mtsdr(SDR0_PFC0, 0x00103E00);
|
|
|
|
/* Setup access for LEDs, and system topology info */
|
|
gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
|
|
gpio_regs->open_drain = SBCOMMON_GPIO_SYS_LEDS;
|
|
gpio_regs->tri_state = SBCOMMON_GPIO_DBGLEDS;
|
|
|
|
/* Turn on all the leds for now */
|
|
gpio_regs->out = SBCOMMON_GPIO_LEDS;
|
|
|
|
/*--------------------------------------------------------------------+
|
|
| Initialize EBC CONFIG
|
|
+-------------------------------------------------------------------*/
|
|
mtebc(EBC0_CFG,
|
|
EBC_CFG_LE_UNLOCK | EBC_CFG_PTD_ENABLE |
|
|
EBC_CFG_RTC_64PERCLK | EBC_CFG_ATC_PREVIOUS |
|
|
EBC_CFG_DTC_PREVIOUS | EBC_CFG_CTC_PREVIOUS |
|
|
EBC_CFG_EMC_DEFAULT | EBC_CFG_PME_DISABLE |
|
|
EBC_CFG_PR_32);
|
|
|
|
/*--------------------------------------------------------------------+
|
|
| 1/2 MB FLASH. Initialize bank 0 with default values.
|
|
+-------------------------------------------------------------------*/
|
|
mtebc(PB0AP,
|
|
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
|
|
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
|
|
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
|
|
EBC_BXAP_WBF_ENCODE(1)| EBC_BXAP_TH_ENCODE(1) |
|
|
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
|
|
EBC_BXAP_PEN_DISABLED);
|
|
|
|
mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
|
|
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
|
|
/*--------------------------------------------------------------------+
|
|
| 8KB NVRAM/RTC. Initialize bank 1 with default values.
|
|
+-------------------------------------------------------------------*/
|
|
mtebc(PB1AP,
|
|
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(10) |
|
|
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
|
|
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
|
|
EBC_BXAP_WBF_ENCODE(1)| EBC_BXAP_TH_ENCODE(1) |
|
|
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
|
|
EBC_BXAP_PEN_DISABLED);
|
|
|
|
mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x48000000) |
|
|
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
|
|
|
|
/*--------------------------------------------------------------------+
|
|
| Compact Flash, uses 2 Chip Selects (2 & 6)
|
|
+-------------------------------------------------------------------*/
|
|
mtebc(PB2AP,
|
|
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
|
|
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
|
|
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
|
|
EBC_BXAP_WBF_ENCODE(0)| EBC_BXAP_TH_ENCODE(1) |
|
|
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
|
|
EBC_BXAP_PEN_DISABLED);
|
|
|
|
mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(0xF0000000) |
|
|
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
|
|
|
|
/*--------------------------------------------------------------------+
|
|
| KaRef Scan FPGA. Initialize bank 3 with default values.
|
|
+-------------------------------------------------------------------*/
|
|
mtebc(PB5AP,
|
|
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
|
|
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
|
|
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
|
|
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
|
|
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
|
|
|
|
mtebc(PB5CR, EBC_BXCR_BAS_ENCODE(0x48200000) |
|
|
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
|
|
|
|
/*--------------------------------------------------------------------+
|
|
| MAC A & B for Kamino. OFEM FPGA decodes the addresses
|
|
| Initialize bank 4 with default values.
|
|
+-------------------------------------------------------------------*/
|
|
mtebc(PB4AP,
|
|
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
|
|
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
|
|
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
|
|
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
|
|
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
|
|
|
|
mtebc(PB4CR, EBC_BXCR_BAS_ENCODE(0x48600000) |
|
|
EBC_BXCR_BS_2MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
|
|
|
|
/*--------------------------------------------------------------------+
|
|
| OFEM FPGA Initialize bank 5 with default values.
|
|
+-------------------------------------------------------------------*/
|
|
mtebc(PB3AP,
|
|
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
|
|
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
|
|
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
|
|
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
|
|
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
|
|
|
|
|
|
mtebc(PB3CR, EBC_BXCR_BAS_ENCODE(0x48400000) |
|
|
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
|
|
|
|
|
|
/*--------------------------------------------------------------------+
|
|
| Compact Flash, uses 2 Chip Selects (2 & 6)
|
|
+-------------------------------------------------------------------*/
|
|
mtebc(PB6AP,
|
|
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
|
|
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
|
|
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
|
|
EBC_BXAP_WBF_ENCODE(0)| EBC_BXAP_TH_ENCODE(1) |
|
|
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
|
|
EBC_BXAP_PEN_DISABLED);
|
|
|
|
mtebc(PB6CR, EBC_BXCR_BAS_ENCODE(0xF0100000) |
|
|
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
|
|
|
|
/*--------------------------------------------------------------------+
|
|
| BME-32. Initialize bank 7 with default values.
|
|
+-------------------------------------------------------------------*/
|
|
mtebc(PB7AP,
|
|
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
|
|
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
|
|
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
|
|
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
|
|
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
|
|
|
|
mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48500000) |
|
|
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
|
|
|
|
/*--------------------------------------------------------------------+
|
|
* Setup the interrupt controller polarities, triggers, etc.
|
|
+-------------------------------------------------------------------*/
|
|
/*
|
|
* Because of the interrupt handling rework to handle 440GX interrupts
|
|
* with the common code, we needed to change names of the UIC registers.
|
|
* Here the new relationship:
|
|
*
|
|
* U-Boot name 440GX name
|
|
* -----------------------
|
|
* UIC0 UICB0
|
|
* UIC1 UIC0
|
|
* UIC2 UIC1
|
|
* UIC3 UIC2
|
|
*/
|
|
mtdcr (UIC1SR, 0xffffffff); /* clear all */
|
|
mtdcr (UIC1ER, 0x00000000); /* disable all */
|
|
mtdcr (UIC1CR, 0x00000000); /* all non- critical */
|
|
mtdcr (UIC1PR, 0xfffffe03); /* polarity */
|
|
mtdcr (UIC1TR, 0x01c00000); /* trigger edge vs level */
|
|
mtdcr (UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
|
|
mtdcr (UIC1SR, 0xffffffff); /* clear all */
|
|
|
|
mtdcr (UIC2SR, 0xffffffff); /* clear all */
|
|
mtdcr (UIC2ER, 0x00000000); /* disable all */
|
|
mtdcr (UIC2CR, 0x00000000); /* all non-critical */
|
|
mtdcr (UIC2PR, 0xffffc8ff); /* polarity */
|
|
mtdcr (UIC2TR, 0x00ff0000); /* trigger edge vs level */
|
|
mtdcr (UIC2VR, 0x00000001); /* int31 highest, base=0x000 */
|
|
mtdcr (UIC2SR, 0xffffffff); /* clear all */
|
|
|
|
mtdcr (UIC3SR, 0xffffffff); /* clear all */
|
|
mtdcr (UIC3ER, 0x00000000); /* disable all */
|
|
mtdcr (UIC3CR, 0x00000000); /* all non-critical */
|
|
mtdcr (UIC3PR, 0xffff83ff); /* polarity */
|
|
mtdcr (UIC3TR, 0x00ff8c0f); /* trigger edge vs level */
|
|
mtdcr (UIC3VR, 0x00000001); /* int31 highest, base=0x000 */
|
|
mtdcr (UIC3SR, 0xffffffff); /* clear all */
|
|
|
|
mtdcr (UIC0SR, 0xfc000000); /* clear all */
|
|
mtdcr (UIC0ER, 0x00000000); /* disable all */
|
|
mtdcr (UIC0CR, 0x00000000); /* all non-critical */
|
|
mtdcr (UIC0PR, 0xfc000000);
|
|
mtdcr (UIC0TR, 0x00000000);
|
|
mtdcr (UIC0VR, 0x00000001);
|
|
|
|
fpga_init();
|
|
|
|
return 0;
|
|
}
|
|
|
|
|
|
/*************************************************************************
|
|
* checkboard
|
|
*
|
|
* Dump pertinent info to the console
|
|
************************************************************************/
|
|
int checkboard (void)
|
|
{
|
|
sys_info_t sysinfo;
|
|
unsigned char brd_rev, brd_id;
|
|
unsigned short sernum;
|
|
unsigned char scan_rev, scan_id, ofem_rev=0, ofem_id=0;
|
|
unsigned char ofem_brd_rev, ofem_brd_id;
|
|
KAREF_FPGA_REGS_ST *karef_ps;
|
|
OFEM_FPGA_REGS_ST *ofem_ps;
|
|
|
|
karef_ps = (KAREF_FPGA_REGS_ST *)CONFIG_SYS_KAREF_FPGA_BASE;
|
|
ofem_ps = (OFEM_FPGA_REGS_ST *)CONFIG_SYS_OFEM_FPGA_BASE;
|
|
|
|
scan_id = (unsigned char)((karef_ps->revision_ul &
|
|
SAND_HAL_KA_SC_SCAN_REVISION_IDENTIFICATION_MASK)
|
|
>> SAND_HAL_KA_SC_SCAN_REVISION_IDENTIFICATION_SHIFT);
|
|
|
|
scan_rev = (unsigned char)((karef_ps->revision_ul & SAND_HAL_KA_SC_SCAN_REVISION_REVISION_MASK)
|
|
>> SAND_HAL_KA_SC_SCAN_REVISION_REVISION_SHIFT);
|
|
|
|
brd_rev = (unsigned char)((karef_ps->boardinfo_ul & SAND_HAL_KA_SC_SCAN_BRD_INFO_BRD_REV_MASK)
|
|
>> SAND_HAL_KA_SC_SCAN_BRD_INFO_BRD_REV_SHIFT);
|
|
|
|
brd_id = (unsigned char)((karef_ps->boardinfo_ul & SAND_HAL_KA_SC_SCAN_BRD_INFO_BRD_ID_MASK)
|
|
>> SAND_HAL_KA_SC_SCAN_BRD_INFO_BRD_ID_SHIFT);
|
|
|
|
ofem_brd_id = (unsigned char)((karef_ps->boardinfo_ul & SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_ID_MASK)
|
|
>> SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_ID_SHIFT);
|
|
|
|
ofem_brd_rev = (unsigned char)((karef_ps->boardinfo_ul & SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_REV_MASK)
|
|
>> SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_REV_SHIFT);
|
|
|
|
if (0xF != ofem_brd_id) {
|
|
ofem_id = (unsigned char)((ofem_ps->revision_ul &
|
|
SAND_HAL_KA_OF_OFEM_REVISION_IDENTIFICATION_MASK)
|
|
>> SAND_HAL_KA_OF_OFEM_REVISION_IDENTIFICATION_SHIFT);
|
|
|
|
ofem_rev = (unsigned char)((ofem_ps->revision_ul &
|
|
SAND_HAL_KA_OF_OFEM_REVISION_REVISION_MASK)
|
|
>> SAND_HAL_KA_OF_OFEM_REVISION_REVISION_SHIFT);
|
|
}
|
|
|
|
get_sys_info (&sysinfo);
|
|
|
|
sernum = sbcommon_get_serial_number();
|
|
|
|
printf ("Board: Sandburst Corporation Kamino Reference Design "
|
|
"Serial Number: %d\n", sernum);
|
|
printf ("%s\n", KAREF_U_BOOT_REL_STR);
|
|
|
|
printf ("Built %s %s by %s\n", U_BOOT_DATE, U_BOOT_TIME, BUILDUSER);
|
|
if (sbcommon_get_master()) {
|
|
printf("Slot 0 - Master\nSlave board");
|
|
if (sbcommon_secondary_present())
|
|
printf(" present\n");
|
|
else
|
|
printf(" not detected\n");
|
|
} else {
|
|
printf("Slot 1 - Slave\n\n");
|
|
}
|
|
|
|
printf ("ScanFPGA ID:\t0x%02X\tRev: 0x%02X\n", scan_id, scan_rev);
|
|
printf ("Board Rev:\t0x%02X\tID: 0x%02X\n", brd_rev, brd_id);
|
|
if(0xF != ofem_brd_id) {
|
|
printf("OFemFPGA ID:\t0x%02X\tRev: 0x%02X\n", ofem_id, ofem_rev);
|
|
printf("OFEM Board Rev:\t0x%02X\tID: 0x%02X\n", ofem_brd_id, ofem_brd_rev);
|
|
}
|
|
|
|
/* Fix the ack in the bme 32 */
|
|
udelay(5000);
|
|
out32(CONFIG_SYS_BME32_BASE + 0x0000000C, 0x00000001);
|
|
asm("eieio");
|
|
|
|
|
|
return (0);
|
|
}
|
|
|
|
/*************************************************************************
|
|
* misc_init_f
|
|
*
|
|
* Initialize I2C bus one to gain access to the fans
|
|
************************************************************************/
|
|
int misc_init_f (void)
|
|
{
|
|
/* Turn on fans 3 & 4 */
|
|
sbcommon_fans();
|
|
|
|
return (0);
|
|
}
|
|
|
|
/*************************************************************************
|
|
* misc_init_r
|
|
*
|
|
* Do nothing.
|
|
************************************************************************/
|
|
int misc_init_r (void)
|
|
{
|
|
unsigned short sernum;
|
|
char envstr[255];
|
|
uchar enetaddr[6];
|
|
KAREF_FPGA_REGS_ST *karef_ps;
|
|
OFEM_FPGA_REGS_ST *ofem_ps;
|
|
|
|
if(NULL != getenv("secondserial")) {
|
|
puts("secondserial is set, switching to second serial port\n");
|
|
setenv("stderr", "serial1");
|
|
setenv("stdout", "serial1");
|
|
setenv("stdin", "serial1");
|
|
}
|
|
|
|
setenv("ubrelver", KAREF_U_BOOT_REL_STR);
|
|
|
|
memset(envstr, 0, 255);
|
|
sprintf (envstr, "Built %s %s by %s",
|
|
U_BOOT_DATE, U_BOOT_TIME, BUILDUSER);
|
|
setenv("bldstr", envstr);
|
|
saveenv();
|
|
|
|
if( getenv("autorecover")) {
|
|
setenv("autorecover", NULL);
|
|
saveenv();
|
|
sernum = sbcommon_get_serial_number();
|
|
|
|
printf("\nSetting up environment for automatic filesystem recovery\n");
|
|
/*
|
|
* Setup default bootargs
|
|
*/
|
|
memset(envstr, 0, 255);
|
|
|
|
sprintf(envstr, "console=ttyS0,9600 root=/dev/ram0 "
|
|
"rw ip=10.100.70.%d:::255.255.0.0:karef%d:eth0:none idebus=33",
|
|
sernum, sernum);
|
|
setenv("bootargs", envstr);
|
|
|
|
/*
|
|
* Setup Default boot command
|
|
*/
|
|
setenv("bootcmd", "fatload ide 0 8000000 uimage.karef;"
|
|
"fatload ide 0 8100000 pramdisk;"
|
|
"bootm 8000000 8100000");
|
|
|
|
printf("Done. Please type allow the system to continue to boot\n");
|
|
}
|
|
|
|
if( getenv("fakeled")) {
|
|
karef_ps = (KAREF_FPGA_REGS_ST *)CONFIG_SYS_KAREF_FPGA_BASE;
|
|
ofem_ps = (OFEM_FPGA_REGS_ST *)CONFIG_SYS_OFEM_FPGA_BASE;
|
|
ofem_ps->control_ul &= ~SAND_HAL_KA_SC_SCAN_CNTL_FAULT_LED_MASK;
|
|
karef_ps->control_ul &= ~SAND_HAL_KA_OF_OFEM_CNTL_FAULT_LED_MASK;
|
|
setenv("bootdelay", "-1");
|
|
saveenv();
|
|
printf("fakeled is set. use 'setenv fakeled ; setenv bootdelay 5 ; saveenv' to recover\n");
|
|
}
|
|
|
|
#ifdef CONFIG_HAS_ETH0
|
|
if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
|
|
board_get_enetaddr(0, enetaddr);
|
|
eth_setenv_enetaddr("ethaddr", enetaddr);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_HAS_ETH1
|
|
if (!eth_getenv_enetaddr("eth1addr", enetaddr)) {
|
|
board_get_enetaddr(1, enetaddr);
|
|
eth_setenv_enetaddr("eth1addr", enetaddr);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_HAS_ETH2
|
|
if (!eth_getenv_enetaddr("eth2addr", enetaddr)) {
|
|
board_get_enetaddr(2, enetaddr);
|
|
eth_setenv_enetaddr("eth2addr", enetaddr);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_HAS_ETH3
|
|
if (!eth_getenv_enetaddr("eth3addr", enetaddr)) {
|
|
board_get_enetaddr(3, enetaddr);
|
|
eth_setenv_enetaddr("eth3addr", enetaddr);
|
|
}
|
|
#endif
|
|
|
|
return (0);
|
|
}
|
|
|
|
/*************************************************************************
|
|
* ide_set_reset
|
|
************************************************************************/
|
|
#ifdef CONFIG_IDE_RESET
|
|
void ide_set_reset(int on)
|
|
{
|
|
KAREF_FPGA_REGS_ST *karef_ps;
|
|
/* TODO: ide reset */
|
|
karef_ps = (KAREF_FPGA_REGS_ST *)CONFIG_SYS_KAREF_FPGA_BASE;
|
|
|
|
if (on) {
|
|
karef_ps->reset_ul &= ~SAND_HAL_KA_SC_SCAN_RESET_CF_RESET_N_MASK;
|
|
} else {
|
|
karef_ps->reset_ul |= SAND_HAL_KA_SC_SCAN_RESET_CF_RESET_N_MASK;
|
|
}
|
|
}
|
|
#endif /* CONFIG_IDE_RESET */
|
|
|
|
/*************************************************************************
|
|
* fpga_init
|
|
************************************************************************/
|
|
void fpga_init(void)
|
|
{
|
|
KAREF_FPGA_REGS_ST *karef_ps;
|
|
OFEM_FPGA_REGS_ST *ofem_ps;
|
|
unsigned char ofem_id;
|
|
unsigned long tmp;
|
|
|
|
/* Ensure we have power all around */
|
|
udelay(500);
|
|
|
|
karef_ps = (KAREF_FPGA_REGS_ST *)CONFIG_SYS_KAREF_FPGA_BASE;
|
|
tmp =
|
|
SAND_HAL_KA_SC_SCAN_RESET_CF_RESET_N_MASK |
|
|
SAND_HAL_KA_SC_SCAN_RESET_BME_RESET_N_MASK |
|
|
SAND_HAL_KA_SC_SCAN_RESET_KA_RESET_N_MASK |
|
|
SAND_HAL_KA_SC_SCAN_RESET_SLAVE_RESET_N_MASK |
|
|
SAND_HAL_KA_SC_SCAN_RESET_OFEM_RESET_N_MASK |
|
|
SAND_HAL_KA_SC_SCAN_RESET_IFE_A_RESET_N_MASK |
|
|
SAND_HAL_KA_SC_SCAN_RESET_I2C_MUX1_RESET_N_MASK |
|
|
SAND_HAL_KA_SC_SCAN_RESET_PHY0_RESET_N_MASK |
|
|
SAND_HAL_KA_SC_SCAN_RESET_PHY1_RESET_N_MASK;
|
|
|
|
karef_ps->reset_ul = tmp;
|
|
|
|
/*
|
|
* Wait a bit to allow the ofem fpga to get its brains
|
|
*/
|
|
udelay(5000);
|
|
|
|
/*
|
|
* Check to see if the ofem is there
|
|
*/
|
|
ofem_id = (unsigned char)((karef_ps->boardinfo_ul & SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_ID_MASK)
|
|
>> SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_ID_SHIFT);
|
|
if(0xF != ofem_id) {
|
|
tmp =
|
|
SAND_HAL_KA_OF_OFEM_RESET_I2C_MUX0_RESET_N_MASK |
|
|
SAND_HAL_KA_OF_OFEM_RESET_LOCH0_RESET_N_MASK |
|
|
SAND_HAL_KA_OF_OFEM_RESET_MAC0_RESET_N_MASK;
|
|
|
|
ofem_ps = (OFEM_FPGA_REGS_ST *)CONFIG_SYS_OFEM_FPGA_BASE;
|
|
ofem_ps->reset_ul = tmp;
|
|
|
|
ofem_ps->control_ul |= 1 < SAND_HAL_KA_OF_OFEM_CNTL_FAULT_LED_SHIFT;
|
|
}
|
|
|
|
karef_ps->control_ul |= 1 << SAND_HAL_KA_SC_SCAN_CNTL_FAULT_LED_SHIFT;
|
|
|
|
asm("eieio");
|
|
|
|
return;
|
|
}
|
|
|
|
int karefSetupVars(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
|
|
{
|
|
unsigned short sernum;
|
|
char envstr[255];
|
|
|
|
sernum = sbcommon_get_serial_number();
|
|
|
|
memset(envstr, 0, 255);
|
|
/*
|
|
* Setup our ip address
|
|
*/
|
|
sprintf(envstr, "10.100.70.%d", sernum);
|
|
|
|
setenv("ipaddr", envstr);
|
|
/*
|
|
* Setup the host ip address
|
|
*/
|
|
setenv("serverip", "10.100.17.10");
|
|
|
|
/*
|
|
* Setup default bootargs
|
|
*/
|
|
memset(envstr, 0, 255);
|
|
|
|
sprintf(envstr, "console=ttyS0,9600 root=/dev/nfs "
|
|
"rw nfsroot=10.100.17.10:/home/metrobox/mbc70.%d "
|
|
"nfsaddrs=10.100.70.%d:10.100.17.10:10.100.1.1:"
|
|
"255.255.0.0:karef%d.sandburst.com:eth0:none idebus=33",
|
|
sernum, sernum, sernum);
|
|
|
|
setenv("bootargs_nfs", envstr);
|
|
setenv("bootargs", envstr);
|
|
|
|
/*
|
|
* Setup CF bootargs
|
|
*/
|
|
memset(envstr, 0, 255);
|
|
|
|
sprintf(envstr, "console=ttyS0,9600 root=/dev/hda2 "
|
|
"rw ip=10.100.70.%d:::255.255.0.0:karef%d:eth0:none idebus=33",
|
|
sernum, sernum);
|
|
|
|
setenv("bootargs_cf", envstr);
|
|
|
|
/*
|
|
* Setup Default boot command
|
|
*/
|
|
setenv("bootcmd_tftp", "tftp 8000000 uImage.karef;bootm 8000000");
|
|
setenv("bootcmd", "tftp 8000000 uImage.karef;bootm 8000000");
|
|
|
|
/*
|
|
* Setup compact flash boot command
|
|
*/
|
|
setenv("bootcmd_cf", "fatload ide 0 8000000 uimage.karef;bootm 8000000");
|
|
|
|
saveenv();
|
|
|
|
return(1);
|
|
}
|
|
|
|
int karefRecover(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
|
|
{
|
|
unsigned short sernum;
|
|
char envstr[255];
|
|
|
|
sernum = sbcommon_get_serial_number();
|
|
|
|
printf("\nSetting up environment for filesystem recovery\n");
|
|
/*
|
|
* Setup default bootargs
|
|
*/
|
|
memset(envstr, 0, 255);
|
|
|
|
sprintf(envstr, "console=ttyS0,9600 root=/dev/ram0 "
|
|
"rw ip=10.100.70.%d:::255.255.0.0:karef%d:eth0:none",
|
|
sernum, sernum);
|
|
setenv("bootargs", envstr);
|
|
|
|
/*
|
|
* Setup Default boot command
|
|
*/
|
|
|
|
setenv("bootcmd", "fatload ide 0 8000000 uimage.karef;"
|
|
"fatload ide 0 8100000 pramdisk;"
|
|
"bootm 8000000 8100000");
|
|
|
|
printf("Done. Please type boot<cr>.\nWhen the kernel has booted"
|
|
" please type fsrecover.sh<cr>\n");
|
|
|
|
return(1);
|
|
}
|
|
|
|
U_BOOT_CMD(kasetup, 1, 1, karefSetupVars,
|
|
"Set environment to factory defaults", "");
|
|
|
|
U_BOOT_CMD(karecover, 1, 1, karefRecover,
|
|
"Set environment to allow for fs recovery", "");
|
|
|