upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
1055 lines
31 KiB
1055 lines
31 KiB
/*
|
|
* Copyright 2008 Freescale Semiconductor, Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* Version 2 as published by the Free Software Foundation.
|
|
*/
|
|
|
|
/*
|
|
* Generic driver for Freescale DDR/DDR2/DDR3 memory controller.
|
|
* Based on code from spd_sdram.c
|
|
* Author: James Yang [at freescale.com]
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/fsl_ddr_sdram.h>
|
|
|
|
#include "ddr.h"
|
|
|
|
extern unsigned int picos_to_mclk(unsigned int picos);
|
|
/*
|
|
* Determine Rtt value.
|
|
*
|
|
* This should likely be either board or controller specific.
|
|
*
|
|
* Rtt(nominal):
|
|
* 0 = Rtt disabled
|
|
* 1 = 75 ohm
|
|
* 2 = 150 ohm
|
|
* 3 = 50 ohm
|
|
*
|
|
* FIXME: Apparently 8641 needs a value of 2
|
|
* FIXME: Old code seys if 667 MHz or higher, use 3 on 8572
|
|
*
|
|
* FIXME: There was some effort down this line earlier:
|
|
*
|
|
* unsigned int i;
|
|
* for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL/2; i++) {
|
|
* if (popts->dimmslot[i].num_valid_cs
|
|
* && (popts->cs_local_opts[2*i].odt_rd_cfg
|
|
* || popts->cs_local_opts[2*i].odt_wr_cfg)) {
|
|
* rtt = 2;
|
|
* break;
|
|
* }
|
|
* }
|
|
*/
|
|
static inline int fsl_ddr_get_rtt(void)
|
|
{
|
|
int rtt;
|
|
|
|
#if defined(CONFIG_FSL_DDR1)
|
|
rtt = 0;
|
|
#elif defined(CONFIG_FSL_DDR2)
|
|
rtt = 3;
|
|
#else
|
|
#error "Need Rtt value for DDR3"
|
|
#endif
|
|
|
|
return rtt;
|
|
}
|
|
|
|
/* Chip Select Configuration (CSn_CONFIG) */
|
|
static void set_csn_config(int i, fsl_ddr_cfg_regs_t *ddr,
|
|
const memctl_options_t *popts,
|
|
const dimm_params_t *dimm_params)
|
|
{
|
|
unsigned int cs_n_en = 0; /* Chip Select enable */
|
|
unsigned int intlv_en = 0; /* Memory controller interleave enable */
|
|
unsigned int intlv_ctl = 0; /* Interleaving control */
|
|
unsigned int ap_n_en = 0; /* Chip select n auto-precharge enable */
|
|
unsigned int odt_rd_cfg = 0; /* ODT for reads configuration */
|
|
unsigned int odt_wr_cfg = 0; /* ODT for writes configuration */
|
|
unsigned int ba_bits_cs_n = 0; /* Num of bank bits for SDRAM on CSn */
|
|
unsigned int row_bits_cs_n = 0; /* Num of row bits for SDRAM on CSn */
|
|
unsigned int col_bits_cs_n = 0; /* Num of ocl bits for SDRAM on CSn */
|
|
|
|
/* Compute CS_CONFIG only for existing ranks of each DIMM. */
|
|
if ((((i&1) == 0)
|
|
&& (dimm_params[i/2].n_ranks == 1))
|
|
|| (dimm_params[i/2].n_ranks == 2)) {
|
|
unsigned int n_banks_per_sdram_device;
|
|
cs_n_en = 1;
|
|
if (i == 0) {
|
|
/* These fields only available in CS0_CONFIG */
|
|
intlv_en = popts->memctl_interleaving;
|
|
intlv_ctl = popts->memctl_interleaving_mode;
|
|
}
|
|
ap_n_en = popts->cs_local_opts[i].auto_precharge;
|
|
odt_rd_cfg = popts->cs_local_opts[i].odt_rd_cfg;
|
|
odt_wr_cfg = popts->cs_local_opts[i].odt_wr_cfg;
|
|
n_banks_per_sdram_device
|
|
= dimm_params[i/2].n_banks_per_sdram_device;
|
|
ba_bits_cs_n = __ilog2(n_banks_per_sdram_device) - 2;
|
|
row_bits_cs_n = dimm_params[i/2].n_row_addr - 12;
|
|
col_bits_cs_n = dimm_params[i/2].n_col_addr - 8;
|
|
}
|
|
|
|
ddr->cs[i].config = (0
|
|
| ((cs_n_en & 0x1) << 31)
|
|
| ((intlv_en & 0x3) << 29)
|
|
| ((intlv_ctl & 0xf) << 24)
|
|
| ((ap_n_en & 0x1) << 23)
|
|
|
|
/* XXX: some implementation only have 1 bit starting at left */
|
|
| ((odt_rd_cfg & 0x7) << 20)
|
|
|
|
/* XXX: Some implementation only have 1 bit starting at left */
|
|
| ((odt_wr_cfg & 0x7) << 16)
|
|
|
|
| ((ba_bits_cs_n & 0x3) << 14)
|
|
| ((row_bits_cs_n & 0x7) << 8)
|
|
| ((col_bits_cs_n & 0x7) << 0)
|
|
);
|
|
debug("FSLDDR: cs[%d]_config = 0x%08x\n", i,ddr->cs[i].config);
|
|
}
|
|
|
|
/* Chip Select Configuration 2 (CSn_CONFIG_2) */
|
|
/* FIXME: 8572 */
|
|
static void set_csn_config_2(int i, fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int pasr_cfg = 0; /* Partial array self refresh config */
|
|
|
|
ddr->cs[i].config_2 = ((pasr_cfg & 7) << 24);
|
|
debug("FSLDDR: cs[%d]_config_2 = 0x%08x\n", i, ddr->cs[i].config_2);
|
|
}
|
|
|
|
/* -3E = 667 CL5, -25 = CL6 800, -25E = CL5 800 */
|
|
|
|
#if defined(CONFIG_FSL_DDR2)
|
|
/*
|
|
* DDR SDRAM Timing Configuration 0 (TIMING_CFG_0)
|
|
*
|
|
* Avoid writing for DDR I. The new PQ38 DDR controller
|
|
* dreams up non-zero default values to be backwards compatible.
|
|
*/
|
|
static void set_timing_cfg_0(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned char trwt_mclk = 0; /* Read-to-write turnaround */
|
|
unsigned char twrt_mclk = 0; /* Write-to-read turnaround */
|
|
/* 7.5 ns on -3E; 0 means WL - CL + BL/2 + 1 */
|
|
unsigned char trrt_mclk = 0; /* Read-to-read turnaround */
|
|
unsigned char twwt_mclk = 0; /* Write-to-write turnaround */
|
|
|
|
/* Active powerdown exit timing (tXARD and tXARDS). */
|
|
unsigned char act_pd_exit_mclk;
|
|
/* Precharge powerdown exit timing (tXP). */
|
|
unsigned char pre_pd_exit_mclk;
|
|
/* Precharge powerdown exit timing (tAXPD). */
|
|
unsigned char taxpd_mclk;
|
|
/* Mode register set cycle time (tMRD). */
|
|
unsigned char tmrd_mclk;
|
|
|
|
/* (tXARD and tXARDS). Empirical? */
|
|
act_pd_exit_mclk = 2;
|
|
|
|
/* XXX: tXARD = 2, tXARDS = 7 - AL. * Empirical? */
|
|
pre_pd_exit_mclk = 6;
|
|
|
|
/* FIXME: tXP = 2 on Micron 667 MHz DIMM */
|
|
taxpd_mclk = 8;
|
|
|
|
tmrd_mclk = 2;
|
|
|
|
ddr->timing_cfg_0 = (0
|
|
| ((trwt_mclk & 0x3) << 30) /* RWT */
|
|
| ((twrt_mclk & 0x3) << 28) /* WRT */
|
|
| ((trrt_mclk & 0x3) << 26) /* RRT */
|
|
| ((twwt_mclk & 0x3) << 24) /* WWT */
|
|
| ((act_pd_exit_mclk & 0x7) << 20) /* ACT_PD_EXIT */
|
|
| ((pre_pd_exit_mclk & 0xF) << 16) /* PRE_PD_EXIT */
|
|
| ((taxpd_mclk & 0xf) << 8) /* ODT_PD_EXIT */
|
|
| ((tmrd_mclk & 0xf) << 0) /* MRS_CYC */
|
|
);
|
|
debug("FSLDDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0);
|
|
}
|
|
#endif /* defined(CONFIG_FSL_DDR2) */
|
|
|
|
/* DDR SDRAM Timing Configuration 3 (TIMING_CFG_3) */
|
|
static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr,
|
|
const common_timing_params_t *common_dimm)
|
|
{
|
|
/* Extended Activate to precharge interval (tRAS) */
|
|
unsigned int ext_acttopre = 0;
|
|
unsigned int ext_refrec; /* Extended refresh recovery time (tRFC) */
|
|
unsigned int ext_caslat = 0; /* Extended MCAS latency from READ cmd */
|
|
unsigned int cntl_adj = 0; /* Control Adjust */
|
|
|
|
/* If the tRAS > 19 MCLK, we use the ext mode */
|
|
if (picos_to_mclk(common_dimm->tRAS_ps) > 0x13)
|
|
ext_acttopre = 1;
|
|
|
|
ext_refrec = (picos_to_mclk(common_dimm->tRFC_ps) - 8) >> 4;
|
|
ddr->timing_cfg_3 = (0
|
|
| ((ext_acttopre & 0x1) << 24)
|
|
| ((ext_refrec & 0xF) << 16)
|
|
| ((ext_caslat & 0x1) << 12)
|
|
| ((cntl_adj & 0x7) << 0)
|
|
);
|
|
debug("FSLDDR: timing_cfg_3 = 0x%08x\n", ddr->timing_cfg_3);
|
|
}
|
|
|
|
/* DDR SDRAM Timing Configuration 1 (TIMING_CFG_1) */
|
|
static void set_timing_cfg_1(fsl_ddr_cfg_regs_t *ddr,
|
|
const common_timing_params_t *common_dimm,
|
|
unsigned int cas_latency)
|
|
{
|
|
/* Precharge-to-activate interval (tRP) */
|
|
unsigned char pretoact_mclk;
|
|
/* Activate to precharge interval (tRAS) */
|
|
unsigned char acttopre_mclk;
|
|
/* Activate to read/write interval (tRCD) */
|
|
unsigned char acttorw_mclk;
|
|
/* CASLAT */
|
|
unsigned char caslat_ctrl;
|
|
/* Refresh recovery time (tRFC) ; trfc_low */
|
|
unsigned char refrec_ctrl;
|
|
/* Last data to precharge minimum interval (tWR) */
|
|
unsigned char wrrec_mclk;
|
|
/* Activate-to-activate interval (tRRD) */
|
|
unsigned char acttoact_mclk;
|
|
/* Last write data pair to read command issue interval (tWTR) */
|
|
unsigned char wrtord_mclk;
|
|
|
|
pretoact_mclk = picos_to_mclk(common_dimm->tRP_ps);
|
|
acttopre_mclk = picos_to_mclk(common_dimm->tRAS_ps);
|
|
acttorw_mclk = picos_to_mclk(common_dimm->tRCD_ps);
|
|
|
|
/*
|
|
* Translate CAS Latency to a DDR controller field value:
|
|
*
|
|
* CAS Lat DDR I DDR II Ctrl
|
|
* Clocks SPD Bit SPD Bit Value
|
|
* ------- ------- ------- -----
|
|
* 1.0 0 0001
|
|
* 1.5 1 0010
|
|
* 2.0 2 2 0011
|
|
* 2.5 3 0100
|
|
* 3.0 4 3 0101
|
|
* 3.5 5 0110
|
|
* 4.0 4 0111
|
|
* 4.5 1000
|
|
* 5.0 5 1001
|
|
*/
|
|
#if defined(CONFIG_FSL_DDR1)
|
|
caslat_ctrl = (cas_latency + 1) & 0x07;
|
|
#elif defined(CONFIG_FSL_DDR2)
|
|
caslat_ctrl = 2 * cas_latency - 1;
|
|
#else
|
|
#error "Need CAS Latency help for DDR3 in fsl_ddr_sdram.c"
|
|
#endif
|
|
|
|
refrec_ctrl = picos_to_mclk(common_dimm->tRFC_ps) - 8;
|
|
wrrec_mclk = picos_to_mclk(common_dimm->tWR_ps);
|
|
acttoact_mclk = picos_to_mclk(common_dimm->tRRD_ps);
|
|
wrtord_mclk = picos_to_mclk(common_dimm->tWTR_ps);
|
|
|
|
ddr->timing_cfg_1 = (0
|
|
| ((pretoact_mclk & 0x0F) << 28)
|
|
| ((acttopre_mclk & 0x0F) << 24)
|
|
| ((acttorw_mclk & 0xF) << 20)
|
|
| ((caslat_ctrl & 0xF) << 16)
|
|
| ((refrec_ctrl & 0xF) << 12)
|
|
| ((wrrec_mclk & 0x0F) << 8)
|
|
| ((acttoact_mclk & 0x07) << 4)
|
|
| ((wrtord_mclk & 0x07) << 0)
|
|
);
|
|
debug("FSLDDR: timing_cfg_1 = 0x%08x\n", ddr->timing_cfg_1);
|
|
}
|
|
|
|
/* DDR SDRAM Timing Configuration 2 (TIMING_CFG_2) */
|
|
static void set_timing_cfg_2(fsl_ddr_cfg_regs_t *ddr,
|
|
const memctl_options_t *popts,
|
|
const common_timing_params_t *common_dimm,
|
|
unsigned int cas_latency,
|
|
unsigned int additive_latency)
|
|
{
|
|
/* Additive latency */
|
|
unsigned char add_lat_mclk;
|
|
/* CAS-to-preamble override */
|
|
unsigned short cpo;
|
|
/* Write latency */
|
|
unsigned char wr_lat;
|
|
/* Read to precharge (tRTP) */
|
|
unsigned char rd_to_pre;
|
|
/* Write command to write data strobe timing adjustment */
|
|
unsigned char wr_data_delay;
|
|
/* Minimum CKE pulse width (tCKE) */
|
|
unsigned char cke_pls;
|
|
/* Window for four activates (tFAW) */
|
|
unsigned short four_act;
|
|
|
|
/* FIXME add check that this must be less than acttorw_mclk */
|
|
add_lat_mclk = additive_latency;
|
|
cpo = popts->cpo_override;
|
|
|
|
#if defined(CONFIG_FSL_DDR1)
|
|
/*
|
|
* This is a lie. It should really be 1, but if it is
|
|
* set to 1, bits overlap into the old controller's
|
|
* otherwise unused ACSM field. If we leave it 0, then
|
|
* the HW will magically treat it as 1 for DDR 1. Oh Yea.
|
|
*/
|
|
wr_lat = 0;
|
|
#elif defined(CONFIG_FSL_DDR2)
|
|
wr_lat = cas_latency + additive_latency - 1;
|
|
#else
|
|
#error "Fix WR_LAT for DDR3"
|
|
#endif
|
|
|
|
rd_to_pre = picos_to_mclk(common_dimm->tRTP_ps);
|
|
wr_data_delay = popts->write_data_delay;
|
|
cke_pls = picos_to_mclk(popts->tCKE_clock_pulse_width_ps);
|
|
four_act = picos_to_mclk(popts->tFAW_window_four_activates_ps);
|
|
|
|
ddr->timing_cfg_2 = (0
|
|
| ((add_lat_mclk & 0xf) << 28)
|
|
| ((cpo & 0x1f) << 23)
|
|
| ((wr_lat & 0xf) << 19)
|
|
| ((rd_to_pre & 0x7) << 13)
|
|
| ((wr_data_delay & 0x7) << 10)
|
|
| ((cke_pls & 0x7) << 6)
|
|
| ((four_act & 0x3f) << 0)
|
|
);
|
|
debug("FSLDDR: timing_cfg_2 = 0x%08x\n", ddr->timing_cfg_2);
|
|
}
|
|
|
|
/* DDR SDRAM control configuration (DDR_SDRAM_CFG) */
|
|
static void set_ddr_sdram_cfg(fsl_ddr_cfg_regs_t *ddr,
|
|
const memctl_options_t *popts,
|
|
const common_timing_params_t *common_dimm)
|
|
{
|
|
unsigned int mem_en; /* DDR SDRAM interface logic enable */
|
|
unsigned int sren; /* Self refresh enable (during sleep) */
|
|
unsigned int ecc_en; /* ECC enable. */
|
|
unsigned int rd_en; /* Registered DIMM enable */
|
|
unsigned int sdram_type; /* Type of SDRAM */
|
|
unsigned int dyn_pwr; /* Dynamic power management mode */
|
|
unsigned int dbw; /* DRAM dta bus width */
|
|
unsigned int eight_be = 0; /* 8-beat burst enable, DDR2 is zero */
|
|
unsigned int ncap = 0; /* Non-concurrent auto-precharge */
|
|
unsigned int threeT_en; /* Enable 3T timing */
|
|
unsigned int twoT_en; /* Enable 2T timing */
|
|
unsigned int ba_intlv_ctl; /* Bank (CS) interleaving control */
|
|
unsigned int x32_en = 0; /* x32 enable */
|
|
unsigned int pchb8 = 0; /* precharge bit 8 enable */
|
|
unsigned int hse; /* Global half strength override */
|
|
unsigned int mem_halt = 0; /* memory controller halt */
|
|
unsigned int bi = 0; /* Bypass initialization */
|
|
|
|
mem_en = 1;
|
|
sren = popts->self_refresh_in_sleep;
|
|
if (common_dimm->all_DIMMs_ECC_capable) {
|
|
/* Allow setting of ECC only if all DIMMs are ECC. */
|
|
ecc_en = popts->ECC_mode;
|
|
} else {
|
|
ecc_en = 0;
|
|
}
|
|
|
|
rd_en = (common_dimm->all_DIMMs_registered
|
|
&& !common_dimm->all_DIMMs_unbuffered);
|
|
|
|
sdram_type = CONFIG_FSL_SDRAM_TYPE;
|
|
|
|
dyn_pwr = popts->dynamic_power;
|
|
dbw = popts->data_bus_width;
|
|
/* DDR3 must use 8-beat bursts when using 32-bit bus mode */
|
|
if ((sdram_type == SDRAM_TYPE_DDR3) && (dbw == 0x1))
|
|
eight_be = 1;
|
|
threeT_en = popts->threeT_en;
|
|
twoT_en = popts->twoT_en;
|
|
ba_intlv_ctl = popts->ba_intlv_ctl;
|
|
hse = popts->half_strength_driver_enable;
|
|
|
|
ddr->ddr_sdram_cfg = (0
|
|
| ((mem_en & 0x1) << 31)
|
|
| ((sren & 0x1) << 30)
|
|
| ((ecc_en & 0x1) << 29)
|
|
| ((rd_en & 0x1) << 28)
|
|
| ((sdram_type & 0x7) << 24)
|
|
| ((dyn_pwr & 0x1) << 21)
|
|
| ((dbw & 0x3) << 19)
|
|
| ((eight_be & 0x1) << 18)
|
|
| ((ncap & 0x1) << 17)
|
|
| ((threeT_en & 0x1) << 16)
|
|
| ((twoT_en & 0x1) << 15)
|
|
| ((ba_intlv_ctl & 0x7F) << 8)
|
|
| ((x32_en & 0x1) << 5)
|
|
| ((pchb8 & 0x1) << 4)
|
|
| ((hse & 0x1) << 3)
|
|
| ((mem_halt & 0x1) << 1)
|
|
| ((bi & 0x1) << 0)
|
|
);
|
|
debug("FSLDDR: ddr_sdram_cfg = 0x%08x\n", ddr->ddr_sdram_cfg);
|
|
}
|
|
|
|
/* DDR SDRAM control configuration 2 (DDR_SDRAM_CFG_2) */
|
|
static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr,
|
|
const memctl_options_t *popts)
|
|
{
|
|
unsigned int frc_sr = 0; /* Force self refresh */
|
|
unsigned int sr_ie = 0; /* Self-refresh interrupt enable */
|
|
unsigned int dll_rst_dis; /* DLL reset disable */
|
|
unsigned int dqs_cfg; /* DQS configuration */
|
|
unsigned int odt_cfg; /* ODT configuration */
|
|
unsigned int num_pr; /* Number of posted refreshes */
|
|
unsigned int obc_cfg; /* On-The-Fly Burst Chop Cfg */
|
|
unsigned int ap_en; /* Address Parity Enable */
|
|
unsigned int d_init; /* DRAM data initialization */
|
|
unsigned int rcw_en = 0; /* Register Control Word Enable */
|
|
unsigned int md_en = 0; /* Mirrored DIMM Enable */
|
|
|
|
dll_rst_dis = 1; /* Make this configurable */
|
|
dqs_cfg = popts->DQS_config;
|
|
if (popts->cs_local_opts[0].odt_rd_cfg
|
|
|| popts->cs_local_opts[0].odt_wr_cfg) {
|
|
/* FIXME */
|
|
odt_cfg = 2;
|
|
} else {
|
|
odt_cfg = 0;
|
|
}
|
|
|
|
num_pr = 1; /* Make this configurable */
|
|
|
|
/*
|
|
* 8572 manual says
|
|
* {TIMING_CFG_1[PRETOACT]
|
|
* + [DDR_SDRAM_CFG_2[NUM_PR]
|
|
* * ({EXT_REFREC || REFREC} + 8 + 2)]}
|
|
* << DDR_SDRAM_INTERVAL[REFINT]
|
|
*/
|
|
|
|
obc_cfg = 0; /* Make this configurable? */
|
|
ap_en = 0; /* Make this configurable? */
|
|
|
|
#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
|
|
/* Use the DDR controller to auto initialize memory. */
|
|
d_init = 1;
|
|
ddr->ddr_data_init = CONFIG_MEM_INIT_VALUE;
|
|
debug("DDR: ddr_data_init = 0x%08x\n", ddr->ddr_data_init);
|
|
#else
|
|
/* Memory will be initialized via DMA, or not at all. */
|
|
d_init = 0;
|
|
#endif
|
|
|
|
ddr->ddr_sdram_cfg_2 = (0
|
|
| ((frc_sr & 0x1) << 31)
|
|
| ((sr_ie & 0x1) << 30)
|
|
| ((dll_rst_dis & 0x1) << 29)
|
|
| ((dqs_cfg & 0x3) << 26)
|
|
| ((odt_cfg & 0x3) << 21)
|
|
| ((num_pr & 0xf) << 12)
|
|
| ((obc_cfg & 0x1) << 6)
|
|
| ((ap_en & 0x1) << 5)
|
|
| ((d_init & 0x1) << 4)
|
|
| ((rcw_en & 0x1) << 2)
|
|
| ((md_en & 0x1) << 0)
|
|
);
|
|
debug("FSLDDR: ddr_sdram_cfg_2 = 0x%08x\n", ddr->ddr_sdram_cfg_2);
|
|
}
|
|
|
|
/* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */
|
|
static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned short esdmode2 = 0; /* Extended SDRAM mode 2 */
|
|
unsigned short esdmode3 = 0; /* Extended SDRAM mode 3 */
|
|
|
|
ddr->ddr_sdram_mode_2 = (0
|
|
| ((esdmode2 & 0xFFFF) << 16)
|
|
| ((esdmode3 & 0xFFFF) << 0)
|
|
);
|
|
debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2);
|
|
}
|
|
|
|
/* DDR SDRAM Interval Configuration (DDR_SDRAM_INTERVAL) */
|
|
static void set_ddr_sdram_interval(fsl_ddr_cfg_regs_t *ddr,
|
|
const memctl_options_t *popts,
|
|
const common_timing_params_t *common_dimm)
|
|
{
|
|
unsigned int refint; /* Refresh interval */
|
|
unsigned int bstopre; /* Precharge interval */
|
|
|
|
refint = picos_to_mclk(common_dimm->refresh_rate_ps);
|
|
|
|
bstopre = popts->bstopre;
|
|
|
|
/* refint field used 0x3FFF in earlier controllers */
|
|
ddr->ddr_sdram_interval = (0
|
|
| ((refint & 0xFFFF) << 16)
|
|
| ((bstopre & 0x3FFF) << 0)
|
|
);
|
|
debug("FSLDDR: ddr_sdram_interval = 0x%08x\n", ddr->ddr_sdram_interval);
|
|
}
|
|
|
|
/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */
|
|
static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr,
|
|
const memctl_options_t *popts,
|
|
const common_timing_params_t *common_dimm,
|
|
unsigned int cas_latency,
|
|
unsigned int additive_latency)
|
|
{
|
|
unsigned short esdmode; /* Extended SDRAM mode */
|
|
unsigned short sdmode; /* SDRAM mode */
|
|
|
|
/*
|
|
* FIXME: This ought to be pre-calculated in a
|
|
* technology-specific routine,
|
|
* e.g. compute_DDR2_mode_register(), and then the
|
|
* sdmode and esdmode passed in as part of common_dimm.
|
|
*/
|
|
|
|
/* Extended Mode Register */
|
|
unsigned int mrs = 0; /* Mode Register Set */
|
|
unsigned int outputs = 0; /* 0=Enabled, 1=Disabled */
|
|
unsigned int rdqs_en = 0; /* RDQS Enable: 0=no, 1=yes */
|
|
unsigned int dqs_en = 0; /* DQS# Enable: 0=enable, 1=disable */
|
|
unsigned int ocd = 0; /* 0x0=OCD not supported,
|
|
0x7=OCD default state */
|
|
unsigned int rtt;
|
|
unsigned int al; /* Posted CAS# additive latency (AL) */
|
|
unsigned int ods = 0; /* Output Drive Strength:
|
|
0 = Full strength (18ohm)
|
|
1 = Reduced strength (4ohm) */
|
|
unsigned int dll_en = 0; /* DLL Enable 0=Enable (Normal),
|
|
1=Disable (Test/Debug) */
|
|
|
|
/* Mode Register (MR) */
|
|
unsigned int mr; /* Mode Register Definition */
|
|
unsigned int pd; /* Power-Down Mode */
|
|
unsigned int wr; /* Write Recovery */
|
|
unsigned int dll_res; /* DLL Reset */
|
|
unsigned int mode; /* Normal=0 or Test=1 */
|
|
unsigned int caslat = 0;/* CAS# latency */
|
|
/* BT: Burst Type (0=Sequential, 1=Interleaved) */
|
|
unsigned int bt;
|
|
unsigned int bl; /* BL: Burst Length */
|
|
|
|
#if defined(CONFIG_FSL_DDR2)
|
|
const unsigned int mclk_ps = get_memory_clk_period_ps();
|
|
#endif
|
|
|
|
rtt = fsl_ddr_get_rtt();
|
|
|
|
al = additive_latency;
|
|
|
|
esdmode = (0
|
|
| ((mrs & 0x3) << 14)
|
|
| ((outputs & 0x1) << 12)
|
|
| ((rdqs_en & 0x1) << 11)
|
|
| ((dqs_en & 0x1) << 10)
|
|
| ((ocd & 0x7) << 7)
|
|
| ((rtt & 0x2) << 5) /* rtt field is split */
|
|
| ((al & 0x7) << 3)
|
|
| ((rtt & 0x1) << 2) /* rtt field is split */
|
|
| ((ods & 0x1) << 1)
|
|
| ((dll_en & 0x1) << 0)
|
|
);
|
|
|
|
mr = 0; /* FIXME: CHECKME */
|
|
|
|
/*
|
|
* 0 = Fast Exit (Normal)
|
|
* 1 = Slow Exit (Low Power)
|
|
*/
|
|
pd = 0;
|
|
|
|
#if defined(CONFIG_FSL_DDR1)
|
|
wr = 0; /* Historical */
|
|
#elif defined(CONFIG_FSL_DDR2)
|
|
wr = (common_dimm->tWR_ps + mclk_ps - 1) / mclk_ps - 1;
|
|
#else
|
|
#error "Write tWR_auto for DDR3"
|
|
#endif
|
|
dll_res = 0;
|
|
mode = 0;
|
|
|
|
#if defined(CONFIG_FSL_DDR1)
|
|
if (1 <= cas_latency && cas_latency <= 4) {
|
|
unsigned char mode_caslat_table[4] = {
|
|
0x5, /* 1.5 clocks */
|
|
0x2, /* 2.0 clocks */
|
|
0x6, /* 2.5 clocks */
|
|
0x3 /* 3.0 clocks */
|
|
};
|
|
caslat = mode_caslat_table[cas_latency - 1];
|
|
} else {
|
|
printf("Warning: unknown cas_latency %d\n", cas_latency);
|
|
}
|
|
#elif defined(CONFIG_FSL_DDR2)
|
|
caslat = cas_latency;
|
|
#else
|
|
#error "Fix the mode CAS Latency for DDR3"
|
|
#endif
|
|
bt = 0;
|
|
|
|
switch (popts->burst_length) {
|
|
case 4:
|
|
bl = 2;
|
|
break;
|
|
case 8:
|
|
bl = 3;
|
|
break;
|
|
default:
|
|
printf("Error: invalid burst length of %u specified. "
|
|
" Defaulting to 4 beats.\n",
|
|
popts->burst_length);
|
|
bl = 2;
|
|
break;
|
|
}
|
|
|
|
sdmode = (0
|
|
| ((mr & 0x3) << 14)
|
|
| ((pd & 0x1) << 12)
|
|
| ((wr & 0x7) << 9)
|
|
| ((dll_res & 0x1) << 8)
|
|
| ((mode & 0x1) << 7)
|
|
| ((caslat & 0x7) << 4)
|
|
| ((bt & 0x1) << 3)
|
|
| ((bl & 0x7) << 0)
|
|
);
|
|
|
|
ddr->ddr_sdram_mode = (0
|
|
| ((esdmode & 0xFFFF) << 16)
|
|
| ((sdmode & 0xFFFF) << 0)
|
|
);
|
|
debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode);
|
|
}
|
|
|
|
|
|
/* DDR SDRAM Data Initialization (DDR_DATA_INIT) */
|
|
static void set_ddr_data_init(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int init_value; /* Initialization value */
|
|
|
|
init_value = 0xDEADBEEF;
|
|
ddr->ddr_data_init = init_value;
|
|
}
|
|
|
|
/*
|
|
* DDR SDRAM Clock Control (DDR_SDRAM_CLK_CNTL)
|
|
* The old controller on the 8540/60 doesn't have this register.
|
|
* Hope it's OK to set it (to 0) anyway.
|
|
*/
|
|
static void set_ddr_sdram_clk_cntl(fsl_ddr_cfg_regs_t *ddr,
|
|
const memctl_options_t *popts)
|
|
{
|
|
unsigned int clk_adjust; /* Clock adjust */
|
|
|
|
clk_adjust = popts->clk_adjust;
|
|
ddr->ddr_sdram_clk_cntl = (clk_adjust & 0xF) << 23;
|
|
}
|
|
|
|
/* DDR Initialization Address (DDR_INIT_ADDR) */
|
|
static void set_ddr_init_addr(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int init_addr = 0; /* Initialization address */
|
|
|
|
ddr->ddr_init_addr = init_addr;
|
|
}
|
|
|
|
/* DDR Initialization Address (DDR_INIT_EXT_ADDR) */
|
|
static void set_ddr_init_ext_addr(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int uia = 0; /* Use initialization address */
|
|
unsigned int init_ext_addr = 0; /* Initialization address */
|
|
|
|
ddr->ddr_init_ext_addr = (0
|
|
| ((uia & 0x1) << 31)
|
|
| (init_ext_addr & 0xF)
|
|
);
|
|
}
|
|
|
|
/* DDR SDRAM Timing Configuration 4 (TIMING_CFG_4) */
|
|
static void set_timing_cfg_4(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int rwt = 0; /* Read-to-write turnaround for same CS */
|
|
unsigned int wrt = 0; /* Write-to-read turnaround for same CS */
|
|
unsigned int rrt = 0; /* Read-to-read turnaround for same CS */
|
|
unsigned int wwt = 0; /* Write-to-write turnaround for same CS */
|
|
unsigned int dll_lock = 0; /* DDR SDRAM DLL Lock Time */
|
|
|
|
ddr->timing_cfg_4 = (0
|
|
| ((rwt & 0xf) << 28)
|
|
| ((wrt & 0xf) << 24)
|
|
| ((rrt & 0xf) << 20)
|
|
| ((wwt & 0xf) << 16)
|
|
| (dll_lock & 0x3)
|
|
);
|
|
debug("FSLDDR: timing_cfg_4 = 0x%08x\n", ddr->timing_cfg_4);
|
|
}
|
|
|
|
/* DDR SDRAM Timing Configuration 5 (TIMING_CFG_5) */
|
|
static void set_timing_cfg_5(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int rodt_on = 0; /* Read to ODT on */
|
|
unsigned int rodt_off = 0; /* Read to ODT off */
|
|
unsigned int wodt_on = 0; /* Write to ODT on */
|
|
unsigned int wodt_off = 0; /* Write to ODT off */
|
|
|
|
ddr->timing_cfg_5 = (0
|
|
| ((rodt_on & 0x1f) << 24)
|
|
| ((rodt_off & 0x7) << 20)
|
|
| ((wodt_on & 0x1f) << 12)
|
|
| ((wodt_off & 0x7) << 8)
|
|
);
|
|
debug("FSLDDR: timing_cfg_5 = 0x%08x\n", ddr->timing_cfg_5);
|
|
}
|
|
|
|
/* DDR ZQ Calibration Control (DDR_ZQ_CNTL) */
|
|
static void set_ddr_zq_cntl(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int zq_en = 0; /* ZQ Calibration Enable */
|
|
unsigned int zqinit = 0;/* POR ZQ Calibration Time (tZQinit) */
|
|
/* Normal Operation Full Calibration Time (tZQoper) */
|
|
unsigned int zqoper = 0;
|
|
/* Normal Operation Short Calibration Time (tZQCS) */
|
|
unsigned int zqcs = 0;
|
|
|
|
ddr->ddr_zq_cntl = (0
|
|
| ((zq_en & 0x1) << 31)
|
|
| ((zqinit & 0xF) << 24)
|
|
| ((zqoper & 0xF) << 16)
|
|
| ((zqcs & 0xF) << 8)
|
|
);
|
|
}
|
|
|
|
/* DDR Write Leveling Control (DDR_WRLVL_CNTL) */
|
|
static void set_ddr_wrlvl_cntl(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int wrlvl_en = 0; /* Write Leveling Enable */
|
|
/*
|
|
* First DQS pulse rising edge after margining mode
|
|
* is programmed (tWL_MRD)
|
|
*/
|
|
unsigned int wrlvl_mrd = 0;
|
|
/* ODT delay after margining mode is programmed (tWL_ODTEN) */
|
|
unsigned int wrlvl_odten = 0;
|
|
/* DQS/DQS_ delay after margining mode is programmed (tWL_DQSEN) */
|
|
unsigned int wrlvl_dqsen = 0;
|
|
/* WRLVL_SMPL: Write leveling sample time */
|
|
unsigned int wrlvl_smpl = 0;
|
|
/* WRLVL_WLR: Write leveling repeition time */
|
|
unsigned int wrlvl_wlr = 0;
|
|
/* WRLVL_START: Write leveling start time */
|
|
unsigned int wrlvl_start = 0;
|
|
|
|
ddr->ddr_wrlvl_cntl = (0
|
|
| ((wrlvl_en & 0x1) << 31)
|
|
| ((wrlvl_mrd & 0x7) << 24)
|
|
| ((wrlvl_odten & 0x7) << 20)
|
|
| ((wrlvl_dqsen & 0x7) << 16)
|
|
| ((wrlvl_smpl & 0xf) << 12)
|
|
| ((wrlvl_wlr & 0x7) << 8)
|
|
| ((wrlvl_start & 0x1F) << 0)
|
|
);
|
|
}
|
|
|
|
/* DDR Self Refresh Counter (DDR_SR_CNTR) */
|
|
static void set_ddr_sr_cntr(fsl_ddr_cfg_regs_t *ddr, unsigned int sr_it)
|
|
{
|
|
/* Self Refresh Idle Threshold */
|
|
ddr->ddr_sr_cntr = (sr_it & 0xF) << 16;
|
|
}
|
|
|
|
/* DDR Pre-Drive Conditioning Control (DDR_PD_CNTL) */
|
|
static void set_ddr_pd_cntl(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
/* Termination value during pre-drive conditioning */
|
|
unsigned int tvpd = 0;
|
|
unsigned int pd_en = 0; /* Pre-Drive Conditioning Enable */
|
|
unsigned int pdar = 0; /* Pre-Drive After Read */
|
|
unsigned int pdaw = 0; /* Pre-Drive After Write */
|
|
unsigned int pd_on = 0; /* Pre-Drive Conditioning On */
|
|
unsigned int pd_off = 0; /* Pre-Drive Conditioning Off */
|
|
|
|
ddr->ddr_pd_cntl = (0
|
|
| ((pd_en & 0x1) << 31)
|
|
| ((tvpd & 0x7) << 28)
|
|
| ((pdar & 0x7F) << 20)
|
|
| ((pdaw & 0x7F) << 12)
|
|
| ((pd_on & 0x1F) << 6)
|
|
| ((pd_off & 0x1F) << 0)
|
|
);
|
|
}
|
|
|
|
|
|
/* DDR SDRAM Register Control Word 1 (DDR_SDRAM_RCW_1) */
|
|
static void set_ddr_sdram_rcw_1(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int rcw0 = 0; /* RCW0: Register Control Word 0 */
|
|
unsigned int rcw1 = 0; /* RCW1: Register Control Word 1 */
|
|
unsigned int rcw2 = 0; /* RCW2: Register Control Word 2 */
|
|
unsigned int rcw3 = 0; /* RCW3: Register Control Word 3 */
|
|
unsigned int rcw4 = 0; /* RCW4: Register Control Word 4 */
|
|
unsigned int rcw5 = 0; /* RCW5: Register Control Word 5 */
|
|
unsigned int rcw6 = 0; /* RCW6: Register Control Word 6 */
|
|
unsigned int rcw7 = 0; /* RCW7: Register Control Word 7 */
|
|
|
|
ddr->ddr_sdram_rcw_1 = (0
|
|
| ((rcw0 & 0xF) << 28)
|
|
| ((rcw1 & 0xF) << 24)
|
|
| ((rcw2 & 0xF) << 20)
|
|
| ((rcw3 & 0xF) << 16)
|
|
| ((rcw4 & 0xF) << 12)
|
|
| ((rcw5 & 0xF) << 8)
|
|
| ((rcw6 & 0xF) << 4)
|
|
| ((rcw7 & 0xF) << 0)
|
|
);
|
|
}
|
|
|
|
/* DDR SDRAM Register Control Word 2 (DDR_SDRAM_RCW_2) */
|
|
static void set_ddr_sdram_rcw_2(fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int rcw8 = 0; /* RCW0: Register Control Word 8 */
|
|
unsigned int rcw9 = 0; /* RCW1: Register Control Word 9 */
|
|
unsigned int rcw10 = 0; /* RCW2: Register Control Word 10 */
|
|
unsigned int rcw11 = 0; /* RCW3: Register Control Word 11 */
|
|
unsigned int rcw12 = 0; /* RCW4: Register Control Word 12 */
|
|
unsigned int rcw13 = 0; /* RCW5: Register Control Word 13 */
|
|
unsigned int rcw14 = 0; /* RCW6: Register Control Word 14 */
|
|
unsigned int rcw15 = 0; /* RCW7: Register Control Word 15 */
|
|
|
|
ddr->ddr_sdram_rcw_2 = (0
|
|
| ((rcw8 & 0xF) << 28)
|
|
| ((rcw9 & 0xF) << 24)
|
|
| ((rcw10 & 0xF) << 20)
|
|
| ((rcw11 & 0xF) << 16)
|
|
| ((rcw12 & 0xF) << 12)
|
|
| ((rcw13 & 0xF) << 8)
|
|
| ((rcw14 & 0xF) << 4)
|
|
| ((rcw15 & 0xF) << 0)
|
|
);
|
|
}
|
|
|
|
unsigned int
|
|
check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr)
|
|
{
|
|
unsigned int res = 0;
|
|
|
|
/*
|
|
* Check that DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] are
|
|
* not set at the same time.
|
|
*/
|
|
if (ddr->ddr_sdram_cfg & 0x10000000
|
|
&& ddr->ddr_sdram_cfg & 0x00008000) {
|
|
printf("Error: DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] "
|
|
" should not be set at the same time.\n");
|
|
res++;
|
|
}
|
|
|
|
return res;
|
|
}
|
|
|
|
unsigned int
|
|
compute_fsl_memctl_config_regs(const memctl_options_t *popts,
|
|
fsl_ddr_cfg_regs_t *ddr,
|
|
const common_timing_params_t *common_dimm,
|
|
const dimm_params_t *dimm_params,
|
|
unsigned int dbw_cap_adj)
|
|
{
|
|
unsigned int i;
|
|
unsigned int cas_latency;
|
|
unsigned int additive_latency;
|
|
unsigned int sr_it;
|
|
|
|
memset(ddr, 0, sizeof(fsl_ddr_cfg_regs_t));
|
|
|
|
if (common_dimm == NULL) {
|
|
printf("Error: subset DIMM params struct null pointer\n");
|
|
return 1;
|
|
}
|
|
|
|
/*
|
|
* Process overrides first.
|
|
*
|
|
* FIXME: somehow add dereated caslat to this
|
|
*/
|
|
cas_latency = (popts->cas_latency_override)
|
|
? popts->cas_latency_override_value
|
|
: common_dimm->lowest_common_SPD_caslat;
|
|
|
|
additive_latency = (popts->additive_latency_override)
|
|
? popts->additive_latency_override_value
|
|
: common_dimm->additive_latency;
|
|
|
|
sr_it = (popts->auto_self_refresh_en)
|
|
? popts->sr_it
|
|
: 0;
|
|
|
|
/* Chip Select Memory Bounds (CSn_BNDS) */
|
|
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
|
|
phys_size_t sa = 0;
|
|
phys_size_t ea = 0;
|
|
|
|
if (popts->ba_intlv_ctl && (i > 0) &&
|
|
((popts->ba_intlv_ctl & 0x60) != FSL_DDR_CS2_CS3 )) {
|
|
/* Don't set up boundaries for other CS
|
|
* other than CS0, if bank interleaving
|
|
* is enabled and not CS2+CS3 interleaved.
|
|
*/
|
|
break;
|
|
}
|
|
|
|
if (dimm_params[i/2].n_ranks == 0) {
|
|
debug("Skipping setup of CS%u "
|
|
"because n_ranks on DIMM %u is 0\n", i, i/2);
|
|
continue;
|
|
}
|
|
if (popts->memctl_interleaving && popts->ba_intlv_ctl) {
|
|
/*
|
|
* This works superbank 2CS
|
|
* There are 2 memory controllers configured
|
|
* identically, memory is interleaved between them,
|
|
* and each controller uses rank interleaving within
|
|
* itself. Therefore the starting and ending address
|
|
* on each controller is twice the amount present on
|
|
* each controller.
|
|
*/
|
|
unsigned long long rank_density
|
|
= dimm_params[0].capacity;
|
|
ea = (2 * (rank_density >> dbw_cap_adj)) - 1;
|
|
}
|
|
else if (!popts->memctl_interleaving && popts->ba_intlv_ctl) {
|
|
/*
|
|
* If memory interleaving between controllers is NOT
|
|
* enabled, the starting address for each memory
|
|
* controller is distinct. However, because rank
|
|
* interleaving is enabled, the starting and ending
|
|
* addresses of the total memory on that memory
|
|
* controller needs to be programmed into its
|
|
* respective CS0_BNDS.
|
|
*/
|
|
unsigned long long rank_density
|
|
= dimm_params[i/2].rank_density;
|
|
switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) {
|
|
case FSL_DDR_CS0_CS1_CS2_CS3:
|
|
/* CS0+CS1+CS2+CS3 interleaving, only CS0_CNDS
|
|
* needs to be set.
|
|
*/
|
|
sa = common_dimm->base_address;
|
|
ea = sa + (4 * (rank_density >> dbw_cap_adj))-1;
|
|
break;
|
|
case FSL_DDR_CS0_CS1_AND_CS2_CS3:
|
|
/* CS0+CS1 and CS2+CS3 interleaving, CS0_CNDS
|
|
* and CS2_CNDS need to be set.
|
|
*/
|
|
if (!(i&1)) {
|
|
sa = dimm_params[i/2].base_address;
|
|
ea = sa + (i * (rank_density >>
|
|
dbw_cap_adj)) - 1;
|
|
}
|
|
break;
|
|
case FSL_DDR_CS0_CS1:
|
|
/* CS0+CS1 interleaving, CS0_CNDS needs
|
|
* to be set
|
|
*/
|
|
sa = common_dimm->base_address;
|
|
ea = sa + (2 * (rank_density >> dbw_cap_adj))-1;
|
|
break;
|
|
case FSL_DDR_CS2_CS3:
|
|
/* CS2+CS3 interleaving*/
|
|
if (i == 2) {
|
|
sa = dimm_params[i/2].base_address;
|
|
ea = sa + (2 * (rank_density >>
|
|
dbw_cap_adj)) - 1;
|
|
}
|
|
break;
|
|
default: /* No bank(chip-select) interleaving */
|
|
break;
|
|
}
|
|
}
|
|
else if (popts->memctl_interleaving && !popts->ba_intlv_ctl) {
|
|
/*
|
|
* Only the rank on CS0 of each memory controller may
|
|
* be used if memory controller interleaving is used
|
|
* without rank interleaving within each memory
|
|
* controller. However, the ending address programmed
|
|
* into each CS0 must be the sum of the amount of
|
|
* memory in the two CS0 ranks.
|
|
*/
|
|
if (i == 0) {
|
|
unsigned long long rank_density
|
|
= dimm_params[0].rank_density;
|
|
ea = (2 * (rank_density >> dbw_cap_adj)) - 1;
|
|
}
|
|
|
|
}
|
|
else if (!popts->memctl_interleaving && !popts->ba_intlv_ctl) {
|
|
/*
|
|
* No rank interleaving and no memory controller
|
|
* interleaving.
|
|
*/
|
|
unsigned long long rank_density
|
|
= dimm_params[i/2].rank_density;
|
|
sa = dimm_params[i/2].base_address;
|
|
ea = sa + (rank_density >> dbw_cap_adj) - 1;
|
|
if (i&1) {
|
|
if ((dimm_params[i/2].n_ranks == 1)) {
|
|
/* Odd chip select, single-rank dimm */
|
|
sa = 0;
|
|
ea = 0;
|
|
} else {
|
|
/* Odd chip select, dual-rank DIMM */
|
|
sa += rank_density >> dbw_cap_adj;
|
|
ea += rank_density >> dbw_cap_adj;
|
|
}
|
|
}
|
|
}
|
|
|
|
sa >>= 24;
|
|
ea >>= 24;
|
|
|
|
ddr->cs[i].bnds = (0
|
|
| ((sa & 0xFFF) << 16) /* starting address MSB */
|
|
| ((ea & 0xFFF) << 0) /* ending address MSB */
|
|
);
|
|
|
|
debug("FSLDDR: cs[%d]_bnds = 0x%08x\n", i, ddr->cs[i].bnds);
|
|
set_csn_config(i, ddr, popts, dimm_params);
|
|
set_csn_config_2(i, ddr);
|
|
}
|
|
|
|
#if defined(CONFIG_FSL_DDR2)
|
|
set_timing_cfg_0(ddr);
|
|
#endif
|
|
|
|
set_timing_cfg_3(ddr, common_dimm);
|
|
set_timing_cfg_1(ddr, common_dimm, cas_latency);
|
|
set_timing_cfg_2(ddr, popts, common_dimm,
|
|
cas_latency, additive_latency);
|
|
|
|
set_ddr_sdram_cfg(ddr, popts, common_dimm);
|
|
|
|
set_ddr_sdram_cfg_2(ddr, popts);
|
|
set_ddr_sdram_mode(ddr, popts, common_dimm,
|
|
cas_latency, additive_latency);
|
|
set_ddr_sdram_mode_2(ddr);
|
|
set_ddr_sdram_interval(ddr, popts, common_dimm);
|
|
set_ddr_data_init(ddr);
|
|
set_ddr_sdram_clk_cntl(ddr, popts);
|
|
set_ddr_init_addr(ddr);
|
|
set_ddr_init_ext_addr(ddr);
|
|
set_timing_cfg_4(ddr);
|
|
set_timing_cfg_5(ddr);
|
|
|
|
set_ddr_zq_cntl(ddr);
|
|
set_ddr_wrlvl_cntl(ddr);
|
|
|
|
set_ddr_pd_cntl(ddr);
|
|
set_ddr_sr_cntr(ddr, sr_it);
|
|
|
|
set_ddr_sdram_rcw_1(ddr);
|
|
set_ddr_sdram_rcw_2(ddr);
|
|
|
|
return check_fsl_memctl_config_regs(ddr);
|
|
}
|
|
|