upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
55 lines
2.3 KiB
55 lines
2.3 KiB
Intel Interrupt Router Device Binding
|
|
=====================================
|
|
|
|
The device tree node which describes the operation of the Intel Interrupt Router
|
|
device is as follows:
|
|
|
|
Required properties :
|
|
- reg : Specifies the interrupt router's PCI configuration space address as
|
|
defined by the Open Firmware spec.
|
|
- compatible = "intel,irq-router"
|
|
- intel,pirq-config : Specifies the IRQ routing register programming mechanism.
|
|
Valid values are:
|
|
"pci": IRQ routing is controlled by PCI configuration registers
|
|
"ibase": IRQ routing is in the memory-mapped IBASE register block
|
|
- intel,ibase-offset : IBASE register offset in the interrupt router's PCI
|
|
configuration space, required only if intel,pirq-config = "ibase".
|
|
- intel,actl-8bit : If ACTL (ACPI control) register width is 8-bit, this must
|
|
be specified. The 8-bit ACTL register is seen on ICH series chipset, like
|
|
ICH9/Panther Point/etc. On Atom chipset it is a 32-bit register.
|
|
- intel,actl-addr : ACTL (ACPI control) register offset. ACTL can be either
|
|
in the interrupt router's PCI configuration space, or IBASE.
|
|
- intel,pirq-link : Specifies the PIRQ link information with two cells. The
|
|
first cell is the register offset that controls the first PIRQ link routing.
|
|
The second cell is the total number of PIRQ links the router supports.
|
|
- intel,pirq-mask : Specifies the IRQ mask representing the 16 IRQs in the
|
|
8259 PIC. Bit N is 1 means IRQ N is available to be routed.
|
|
- intel,pirq-routing : Specifies all PCI devices' IRQ routing information,
|
|
encoded as 3 cells a group for a device. The first cell is the device's PCI
|
|
bus number, device number and function number encoding with PCI_BDF() macro.
|
|
The second cell is the PCI interrupt pin used by this device. The last cell
|
|
is which PIRQ line the PCI interrupt pin is routed to.
|
|
|
|
|
|
Example
|
|
-------
|
|
|
|
#include <dt-bindings/interrupt-router/intel-irq.h>
|
|
|
|
irq-router@1f,0 {
|
|
reg = <0x0000f800 0 0 0 0>;
|
|
compatible = "intel,irq-router";
|
|
intel,pirq-config = "pci";
|
|
intel,pirq-link = <0x60 8>;
|
|
intel,pirq-mask = <0xdef8>;
|
|
intel,pirq-routing = <
|
|
PCI_BDF(0, 2, 0) INTA PIRQA
|
|
PCI_BDF(0, 3, 0) INTA PIRQB
|
|
PCI_BDF(0, 8, 0) INTA PIRQC
|
|
PCI_BDF(0, 8, 1) INTB PIRQD
|
|
PCI_BDF(1, 6, 0) INTA PIRQE
|
|
PCI_BDF(1, 6, 1) INTB PIRQF
|
|
PCI_BDF(1, 6, 2) INTC PIRQG
|
|
PCI_BDF(1, 6, 3) INTD PIRQH
|
|
>;
|
|
};
|
|
|