upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
84 lines
2.8 KiB
84 lines
2.8 KiB
config DM_SERIAL
|
|
bool "Enable Driver Model for serial drivers"
|
|
depends on DM
|
|
help
|
|
Enable driver model for serial. This replaces
|
|
drivers/serial/serial.c with the serial uclass, which
|
|
implements serial_putc() etc. The uclass interface is
|
|
defined in include/serial.h.
|
|
|
|
config DEBUG_UART
|
|
bool "Enable an early debug UART for debugging"
|
|
help
|
|
The debug UART is intended for use very early in U-Boot to debug
|
|
problems when an ICE or other debug mechanism is not available.
|
|
|
|
To use it you should:
|
|
- Make sure your UART supports this interface
|
|
- Enable CONFIG_DEBUG_UART
|
|
- Enable the CONFIG for your UART to tell it to provide this interface
|
|
(e.g. CONFIG_DEBUG_UART_NS16550)
|
|
- Define the required settings as needed (see below)
|
|
- Call debug_uart_init() before use
|
|
- Call debug_uart_putc() to output a character
|
|
|
|
Depending on your platform it may be possible to use this UART before
|
|
a stack is available.
|
|
|
|
If your UART does not support this interface you can probably add
|
|
support quite easily. Remember that you cannot use driver model and
|
|
it is preferred to use no stack.
|
|
|
|
You must not use this UART once driver model is working and the
|
|
serial drivers are up and running (done in serial_init()). Otherwise
|
|
the drivers may conflict and you will get strange output.
|
|
|
|
choice
|
|
prompt "Select which UART will provide the debug UART"
|
|
depends on DEBUG_UART
|
|
|
|
config DEBUG_UART_NS16550
|
|
bool "ns16550"
|
|
help
|
|
Select this to enable a debug UART using the ns16550 driver. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver model serial is running.
|
|
|
|
endchoice
|
|
|
|
config DEBUG_UART_BASE
|
|
hex "Base address of UART"
|
|
depends on DEBUG_UART
|
|
help
|
|
This is the base address of your UART for memory-mapped UARTs.
|
|
|
|
A default should be provided by your board, but if not you will need
|
|
to use the correct value here.
|
|
|
|
config DEBUG_UART_CLOCK
|
|
int "UART input clock"
|
|
depends on DEBUG_UART
|
|
help
|
|
The UART input clock determines the speed of the internal UART
|
|
circuitry. The baud rate is derived from this by dividing the input
|
|
clock down.
|
|
|
|
A default should be provided by your board, but if not you will need
|
|
to use the correct value here.
|
|
|
|
config DEBUG_UART_SHIFT
|
|
int "UART register shift"
|
|
depends on DEBUG_UART
|
|
default 0 if DEBUG_UART
|
|
help
|
|
Some UARTs (notably ns16550) support different register layouts
|
|
where the registers are spaced either as bytes, words or some other
|
|
value. Use this value to specify the shift to use, where 0=byte
|
|
registers, 2=32-bit word registers, etc.
|
|
|
|
config UNIPHIER_SERIAL
|
|
bool "Support for UniPhier on-chip UART"
|
|
depends on ARCH_UNIPHIER && DM_SERIAL
|
|
help
|
|
If you have a UniPhier based board and want to use the on-chip
|
|
serial ports, say Y to this option. If unsure, say N.
|
|
|