DM3730 CPU used on beagleboard-xm doesn't have any gpio
multiplexed with wait0 pin,
but gpio_63 multiplexed with wait1, so it looks like typo.
At current form it has no sense,
because of wait0 have no function "4".
Signed-off-by: Evgneiy A. Dushistov <dushistov@mail.ru>
UART3 RX and TX pins are now moved to support uart download capability
on the platform. Old pins are now GPIOs routed to expansion ports.
All original boards should either have been returned for modifications
or already modified for the required change and maintaining
compatibility for older boards are no longer needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Due to licensing issues, the files ps7_init.c/h are not able to be
distributed with U-Boot source code. Recent Xilinx tools also
provide the GPL variants (ps7_init_gpl.c/h), compatible with U-Boot
license.
Prior to this commit, we had to copy ps7_init files into
board/xilinx/zynq/ before the compile.
To be more user-friendly, let's include ps7_init_gpl.c/h for
Zedboard, MicroZed, ZC702, ZC706.
These init code have been taken from the hwplatform_templates
directory of Xilinx SDK 2014.4.
You can still use customized ps7_init_gpl.c/h by enabling
CONFIG_ZYNQ_CUSTOM_INIT. The recommended directory for storing them
is now board/xilinx/zynq/custom_hw_platform, but board/xilinx/zynq
is still supported for backward compatibility. The latter emits
a warning message to prompt users to gradually switch to the new
directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Prior to this commit, ZC702 and ZC706 shared the same configuration
and were built as follows:
ZC702: make zynq_zc70x_defconfig && make
ZC706: make zynq_zc70x_defconfig && make DEVICE_TREE=zynq-zc706
This commit introduces separate configuration for them, which makes
the next commit much easier.
Going forward, the recommended build commands are:
ZC702: make zynq_zc702_defconfig && make
ZC706: make zynq_zc706_defconfig && make
Although the old work flow is still supported, CONFIG_TARGET_ZC70X
has been marked as deprecated. If used, the warning message is
shown to prompt users to switch to the new scheme.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently we need to build one U-boot image for each of the wandboard
variants: quad, dual-lite and solo.
By switching to SPL we can support all these variants with a single binary,
which is very convenient.
Based on the work from Richard Hu.
Tested kernel booting on the three boards.
Signed-off-by: Richard Hu <hakahu@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
Reviewed-by: Stefano Babic <sbabic@denx.de>
ccsr_ddr structure is already defined in fsl_immap.h. Remove
this duplicated define. Move fixed timing into ls1021atwr.h.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Remove the calls to net_random_ethaddr() that some boards and some
drivers are calling. This is now implemented inside of net/eth.c
Enable the feature for all boards that previously enabled it.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-By: Michael Walle <michael@walle.cc> (for the lsxl board part)
Series-changes: 2
-Fixed bfin build errors
sunxi_usbc_vbus_detect was renamed to sunxi_usb_phy_vbus_detect but
g_dnl_board_usb_cable_connected was still using the old name, breaking the build
when USB gadget is enabled.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The ga10h is an 10" tablet with an A33 or A23 soc, 1G RAM, 8G or 16G nand,
sdio wifi, 2 micro usb ports, 1 otg and 1 host and 1 micro sd slot.
This commit adds a defconfig for the v1.1 pcb with an a33 soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Make DRAM_ODT_EN Kconfig setting a bool, add a separate DRAM_ODT_CORRECTION
setting for A23 SoCs and use DRAM_ODT_EN Kconfig everywhere instead of
only in dram_sun4i.c and hardcoding odt_en elsewhere.
Note this commit makes no functional changes for existing boards,
its purpose is to allow changing the odt_en value on future A33 boards.
For sun4i/sun5i/sun7i boards which set DRAM_ODT_EN=y (which no defconfigs
currently do) this patch turns on odt for both the DQ and the DQS lines,
whereas previously it was possibly (but not desirable) to turn odt on only
for one of them by setting the in DRAM_ODT_EN option to 1 or 2 instead of 3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
We don't need this on sunxi, as we always use calloc or memset when
initialised memory is required. Clearing this shaves some time of our
boot time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The 'mx6-microsom' directory was only used for the previous mx6solo
hummingboard support, which has been removed in favour of the SPL
version.
Remove the remaining piece of the old mx6solo hummingboard support.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Certain features we desire require a larger stack than is available by using
iRAM (most notably for us, env_mmc). Relocate the stack to DRAM so that
we can use these features.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the SPL is to be used for Falcon mode then we need to make sure the SPL
disable the GSC boot watchdog.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
If the SPL is to be used for Falcon mode then we need to make sure it
configures basic GPIO (iomux, padconf, and default output levels).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Now that uart and i2c setup functions have been moved to common.c we can
use these and remove code duplication.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Avoid requiring board-model and probe pmic by its i2c address.
This is in preparation for being able to call pmic_setup() from SPL
and not need board type.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Move shared functions used by both SPL and U-Boot to common.c:
- setup_iomux_uart() and uart pad config
- gpio pad config
In the process also moved the following to common.c in preparation for
calling it from the SPL:
- split i2c setup into a shared function
- move pmic init to setup_pmic() function to call directly from
power_init_board()
- split gpio setup into early (iomux and default pin config)
and late (output configuration based on env)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
PCI enumeration occurs early, before we fully configure our GPIO's. Make
sure we steer the MSATA/PCI mux to PCI in board_init to ensure PCI is
selected before enumeration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The re-assignment of pcie_rst gpio for GW522x needs to occur earlier, before
the PCI subsystem calls the toggle funciton.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Prior to using a gpio a call to gpio_request() should be called to register
it with the gpio subsystem.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for USB OTG host mode. Only high speed devices supported so far
(e.g. usb 2.0 hub required to connect a keyboard).
Signed-off-by: Soeren Moch <smoch@web.de>
Hummingboard dual, dual-lite and solo are now supported via SPL mechanism.
Remove the previous hummingboard support, which does not use SPL and supported
only the solo variant.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This fixes a regression caused by e25fbe3fe5
(gw_ventana: Move the DCD settings to spl code)
The clock gating must be setup prior to calling arch_cpu_init(). Without this
booting to SD (directly via eFuse or via bmode) will hang.
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
By making the tqma6_iomuxc_spi() weak, this patch adds the possibility to
add a different function for this SPI configuration. This can be used
by other baseboards, that might have a different SPI setup.
This patch will be used by the upcoming WRU-IV board support which also
uses the TQMa6 SoM.
Signed-off-by: Stefan Roese <sr@denx.de>
Configure PAD_ENET_RXD0/RXD1 pads as pull down because these pads are directly
connected to the Atheros 8035/8030 although they should be functional
only in the RMII mode - 8030.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-By: Vagrant Cascadian <vagrant@aikidev.net>
mx6cuboxi sometimes fails to recognize the Ethernet PHY:
Net: Phy 0 not found
The explanation for this behavior comes from from Rabeeh Khoury:
"The LED_ACT pin on the carrier-one boards had a pull down that
forces the phy address to 0x0; where on CuBox-i and the production
HummingBoard that pin is connected directly to LED that depending
on the pull down strength of the LED it might be sampled as '0' or '1' thus
the phy address might appear as either address 0x0 or 0x4."
"This is AR8035 implementation; in reset stage the LED pin is configured as
input, and pull up/down does matter. In this case it configures the PHY
address.
After reset is deasserted the same LED pin becomes output and then
according to the previous pull/up it should be active high/low"
One way to properly fix this behavior is to place external pull-up/down
resistors in the LED line, but from a software standpoint we can fix it
by telling phy_find_by_mask() to scan the PHY at addresses
0x0 and 0x4.
Reported-by: Vagrant Cascadian <vagrant@aikidev.net>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-By: Vagrant Cascadian <vagrant@aikidev.net>
Add HDMI output using PLL5 as the source for the IPU clocks,
and accurate VESA timings.
These settings are based on the patch from Soeren Moch <smoch@web.de>
submitted for the tbs2910 mx6 based board.
It allows the display to work properly at 1024x768@60.
This should make the hdmi output signal compatible with most if not all
modern displays.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
This cleanup includes:
- remove of the preprocessor macros which pointed to long name functions
- update of the names of some regulator uclass driver functions
- cleanup of the function regulator_autoset()
- reword of some comments of regulator uclass header file
- regulator_get_by_platname: check error for uclass_find_* function calls
- add function: regulator_name_is_unique
- regulator post_bind(): check regulator name uniqueness
- fix mistakes in: regulator/Kconfig
- regulator.h: update comments
- odroid u3: cleanup the regulator calls
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
This change enables the configs required to init and setup max77686
regulator driver, using the new driver model pmic and regulator API.
And also changes the old pmic framework calls to the new ones.
This commits enables:
- CONFIG_ERRNO_STR
- CONFIG_DM_PMIC
- CONFIG_DM_PMIC_CMD
- CONFIG_DM_PMIC_MAX77686
- CONFIG_DM_REGULATOR
- CONFIG_DM_REGULATOR_CMD
- CONFIG_DM_REGULATOR_MAX77686
And removes the unused:
- CONFIG_DM_I2C_COMPAT
- CONFIG_POWER
- CONFIG_POWER_I2C
- CONFIG_POWER_MAX77686
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
In the power_init_board function call, regulator driver init is called,
so before compile, make sure that any power framework is defined.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert sunxi-boards which use the sunxi-ehci code to the driver-model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
All the Tegra boards borrow the files from board/nvidia/common/
directory, i.e., board/nvidia/common/* are not vendor-common files,
but SoC-common files.
Move NVIDIA common files to arch/arm/mach-tegra/ to clean up
Makefiles.
As arch/arm/mach-tegra/board.c already exists, this commit renames
board/nvidia/common/board.c to arch/arm/mach-tegra/board2.c,
expecting they will be consolidated as a second step.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_ARMV7_VIRT depends on CONFIG_ARMV7_NONSEC, thus doesn't need to
be taken into account additionally. CONFIG_ARMV7_PSCI is only set on
boards that support CONFIG_ARMV7_NONSEC, and it only works on those.
CC: Tang Yuantian <Yuantian.Tang@freescale.com>
CC: York Sun <yorksun@freescale.com>
CC: Steve Rae <srae@broadcom.com>
CC: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add required setup for the LCD display, and a function to provide the
board ID. This requires GPIOs to be available prior to relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for this PMIC which is used on some Tegra124 boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some LCDs require a PMIC to be set up - add a function for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Evgeniy Dushistov
Lokesh Vutla
Tim Harvey
Heiko Schocher
Masahiro Yamada
Fabio Estevam
York Sun
Joe Hershberger
Paul Kocialkowski
Hans de Goede
Peng Fan
Soeren Moch
Stefan Roese
Przemyslaw Marczak
Jan Kiszka
Simon Glass