- Take maintainership of the integratorcp board
- Remove the double entry for the versatile board
it has two variants but only one board folder
Cc: Philippe Robin <philippe.robin@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire:Clean up the CONFIG_STANDALONE_LOAD_ADDR usage
ColdFire:Add mb for 5253 dram initialization
ColdFire:Define the DM9000 byteswap for M5253 board.
ColdFire:Update the env settings for several boards.
ColdFire:disable the NFS define for 52277 board.
ColdFire:Update the timer_init since it was unified.
ColdFire: Cleanup for partial linking and --gc-sections
ColdFire: Update compile flags for each CPUs
ColdFire:Fix the configuration broken for some boards.
* 'master' of git://git.denx.de/u-boot-arm: (145 commits)
beagleboard: enable HUB power on all variants of the BeagleBoard
dm3730: enable dpll5
ehci-hcd: Allow cleanups to happen gracefully on a timeout.
OMAP3: Add DSS driver for OMAP3
led: Remove state-saving of led for toggle functionality and add toggle option to led command
led: Fixed setting of STATUS_LED_BIT1 when led_name is 'all'
led: correct off/on locations in structure
led: added cmd_led to Makefile
BeagleBoard: fix LED 0/1 in driver
Corrected LED name match finding avoiding extraneous Usage printouts
BeagleBoard: config: updated default configuration
BeagleBoard: config: Enabled multibus support for I2C in configuration
BeagleBoard: config: add optargs/buddy/camera
BeagleBoard: config: increase command-line functionality
BeagleBoard: config: make mtest run
BeagleBoard: config: enable DSS
BeagleBoard: config: enable asix driver and dhcp
BeagleBoard: config: enable networking
BeagleBoard: config: decrease bootdelay to 2 seconds
BeagleBoard: config: use uImage.beagle for tftp
BeagleBoard: config: hardcode MAC for onboard SMSC
BeagleBoard: config: load kernel from MMC ext, not FAT
BeagleBoard: Configure DVI/S-video
BeagleBoard: Added userbutton command
BeagleBoard: turn off clocks in ehci_stop
USB: Remove __attribute__ ((packed)) for struct ehci_hccr and ehci_hcor
beagleboard: add support for xM revision C
beagle: pass expansionboard name in bootargs
OMAP: Remove omapfb.debug=y from Beagle and Overo env settings
OMAP3 Beagle Pin Mux initialization glitch fix
da850: modifications for Logic PD Rev.3 AM18xx EVM
da850: fix the channel number for EMAC teardown init
da850: add support for Spectrum Digital AM18xx EVM
da850: add support to wake up DSP during board init
da850: modify the U-Boot prompt string
da850: add NOR boot mode support
da8xx: add support for multiple PLL controllers
da850: indicate cache usage disable in config file
dm365: modify boot prompt from dm365 to dm36x
dm365: disable cache usage due to coherency issues
dm6446: disable cache usage due to coherency issues
OMAP3: Remove legacy mmc driver
devkit8000: Use generic MMC driver
TI OMAP3 SDP3430: Use generic MMC driver
AM3517 CraneBoard: Use generic MMC driver
OMAP3: pandora: Use generic MMC driver
OMAP3: Zoom2: Use generic MMC driver
OMAP3: Zoom1: Use generic MMC driver
OMAP3: DIG297: Use generic MMC driver
OMAP3: CM-T35: Use generic MMC driver
am3517evm: Use generic MMC driver
omap3evm: Use generic MMC driver
omap3:clock: check cpu_family before enabling clks for IVA & CAM
omap3:clock: configure GFX clock to 200MHz for AM/DM37x
OMAP3/4: Increase console I/O buffer size
PXA: vpac270: Remove re-defined CONFIG_SYS_TEXT_BASE
PXA: Fix CSB226, fix monitor length
PXA: Fix Lubbock, remove redundant parenthesis
armv7: cache: remove flush on un-aligned invalidate
armv7: stronger barrier for cache-maintenance operations
omap: enable caches at system start-up
arm: do not force d-cache enable on all boards
ORIGEN: Add MMC SPL support
ARMV7: Add support for Samsung ORIGEN board
i2c:gpio:s5p: Enable I2C GPIO on the GONI target
i2c:gpio:s5p: I2C GPIO Software implementation (via soft_i2c)
Tegra2: Use clock and pinmux functions to simplify code
Tegra2: Add additional pin multiplexing features
Tegra2: Add more clock support
Tegra2: Add microsecond timer function
ARM: remove broken "at91rm9200dk" board
ARM: remove broken "m501sk" board
ARM: remove broken "kb9202" board
ARM: remove broken "csb637" board
ARM: remove broken "cmc_pu2" board
ARM: remove broken "at91cap9adk" board
ARM: remove broken "voiceblue" board
ARM: remove broken "smdk2400" board
ARM: remove broken "sbc2410x" board
ARM: remove broken "netstar" board
ARM: remove broken "mx1fs2" board
ARM: remove broken "lpd7a40x" boards
ARM: remove broken "edb93xx" boards
ARM: remove broken "B2" board
ARM: remove broken "armadillo" board
ARM: remove broken "assabet" board
ARM: versatile: drop warnings
IMX: scb9328: drop warnings
MX31: imx31_litekit: make use of GPIO framework
MX31: mx31ads: make use of GPIO framework
MX5: mx51evk: make use of GPIO framework
MX35: mx35pdk: make use of GPIO framework
MX5: mx53loco: make use of GPIO framework
MX5: mx53evk: make use of GPIO framework
MX5: vision2: make use of GPIO framework
MX5: mx53smd: make use of GPIO framework
MX5: mx53ard: make use of GPIO framework
MX25: zmx25: make use of GPIO framework
MX5: efikamx: make use of GPIO framework
MX31: QONG: make use of GPIO framework
MX35: make use of GPIO framework for MX35 processor
MX5: make use of GPIO framework for MX5 processor
MX31: make use of GPIO framework for MX31 processor
MX25: make use of GPIO framework for MX25 processor
IMX: uniform GPIO interface using GPIO framework
MX: MX35 / MX5: uniform clock command with powerpc
MX35: MX35PDK: support additional RAM on CSD1
mx53: ddr3: Update DD3 initialization
ARM: MX51: PLL errata workaround
ARM: versatilepb : drop warnings due to double definitions
omap4: increase SRAM budget to fix build error
omap4: fix build warning due to signed unsigned comparison
mkimage: Fix 'Unknown OMAP image type - 5'
omap: fix gpio related build breaks
gpio:samsung: s5p_ suffix add for GPIO functions (C210_universal)
SMDKV310: MMC SPL: Remove unwanted dummy functions
SMDKV310: Fix undefined reference error
SMDKV310: Fix build error for smdkv310 board
gpio:samsung s5p_ suffix add for GPIO functions
mmc: S5P: Support DMA restarts at buffer boundaries
SMDKV310: Fix host compilation of mkv310_image
arm: fix bd pointer dereference prior initialization
arm, lib/board.c: use gd->ram_size instead of bd->bi_memsize
mx5: Remove CONFIG_L2_OFF and CONFIG_SYS_L2CACHE_OFF
MX31: removed warnings due to clock.h
integrator: convert to new build system
integratorcp: make the board compile
integratorap: remove hardcoded 32MB memory cmdline
...
The dram initialization sequence should be in order.
This patch add mb for the dram intialization code to make
sure the compiler do not disorder the code.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
The M5253DEMO board swapped the io pins which make
the standard IO function did not work for dm9000.
Define the byte swap to use raw io for dm9000.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Move the environment outside the u-boot for some boards
and enlarge the u-boot size in some env settings.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
There is no network device on ColdFire 52277EVB board.But the default
cmd include NFS define which make the build error.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Introduce the --gc-sections for ColdFire platform and clean up the
corresponding lds file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Remove compiler version check for gcc 4.1 in config.mk.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
which is used to provide 120MHz to USB EHCI
This allows EHCI to work on BeagleBoard XM
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
With this, the EHCI seems to "recover" from a timeout. This is particularly
observable if you were to ping the wrong IP Address and then ping the correct
one or if there was a temporary failure during tftp sessions.
All it takes is one timeout to disable it. If you have a noisy network (lot
of traffic), even if the traffic is not for the board, the timeouts don't occur.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Read the led output state from GPIO instead saving state in memory when it is [re]set
* Added a toggle option to the led command
Previous discussion:
http://lists.denx.de/pipermail/u-boot/2011-May/093068.html
Changes since v1:
Fixed checkpatch errors
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fix for only one led getting set or reset when the led_name is 'all'
Previous discussion:
http://lists.denx.de/pipermail/u-boot/2011-May/093068.html
Changes since v1:
Fixed checkpatch if statement error noticed by Sergei.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Although the initialization should probably be done with names, the
existing implementation has these structures filled in the opposite
order.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Addition of cmd_led into the Makefile wasn't included in the patch
applied to u-boot-ti.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fixed USR0/USR1 to be LED 0/1 respectively
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Improved boot env var setting
* Made room for a 64MB ramdisk by moving from 0x81600000 to 0x81000000
* Added ramarg, ramroot and ramboot env variables
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
buddy and camera are used to configure peripherals in the kernel at boot
time that cannot easily be detected by the kernel.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Utilize the alternate mtest and define a valid region.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on patches from Syed Mohammed Khasim (khasim@ti.com).
Configures the output of the BeagleBoard DVI to be orange.
Configures the output of the BeagleBoard S-Video to be a colorbar.
Changed display_init to beagle_display_init as suggested by Igor Grinberg:
http://www.mail-archive.com/u-boot@lists.denx.de/msg51446.html
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on commit f1099c7c43caf5bac3bf6a65aa266fade4747072
Author: Greg Turner <gregturner@ti.com>
Date: Tue May 25 09:19:06 2010 -0500
New u-boot command for status of USER button on BeagleBoard-xM
Modified bootcmd to check the staus at boot time and set
filename of the boot script.
* Moved to a BeagleBoard specific file.
* Removed changes to default boot command from adding userbutton
command.
* Made to handle pre-xM boards.
* Flipped polarity of the return value to avoid confusion. Success (0)
is when the button is pressed. Failure (1) is when the button is NOT
pressed.
* Used latest revision getting function.
* Used latest macros for board revision.
* Added xM-C revision definition (optional, since it was default)
* updated default configuration with UserButton functionality
* Added a separate bootenv variable to load a user defined .txt file
* Added an example, showing how a different environment file can be loaded with
the user button pressed
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Greg Turner <gregturner@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This fixes display problems in linux
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Remove __attribute__ ((packed)) to prevent byte access to soc
registers in some gcc versions.
Having patches to enable ehci for the BeagleBoard lying around for
several months, this one was the show-stopper.
Switched to align(4), rather than remove the attribute, per suggestion
from Alexander.
Credits have to go to Laine Walker-Avina <lwalkera@ieee.org> for
finding the problem.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Alexander Holler <holler@ahsoftware.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The kernel DSS2 code is mature now, and keeping this setting hurts performance
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The below patch reverses the order of two segments in the board file.
Output pins need to have their values initialized, before they are
exposed to the logic outside the chip.
Signed-off-by: Bob Feretich <bob.feretich@rafresearch.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
NOR to work on Rev.3 EVM. When GP0[11] is low,
the SD0 interface will not work, but NOR flash will.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TX and RX channel numbers programmed as '1' during EMAC
teardown initialization is wrong. This patch fixes the
same by setting channel number to '0' which is used by U-boot.
Signed-off-by: Sugumar Natarajan <sugumar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The AM18xx EVM contains winbond SPI flash instead of ST SPI flash in
comparison with logic PD da850/omap-l138 EVM. So enable configuration
to look for winbond flash.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
add support for DSP wake-up by default on DA850/OMAP-L138
during board initialization. Enable hwconfig environment and added
extra env setting through CONFIG_EXTRA_ENV_SETTINGS.
To prevent DSP from being woken up,set the environment variable as,
set hwconfig "dsp:wake=no"
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add pin-mux support for NOR in board file and correspanding
macros to use NOR boot mode in configuration file.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Modify clk_get() function in cpu file to work for
multiple PLL controllers.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
there are cache coherency issues when using the DAVINCI Ethernet driver,
hence caches cant be used for da850 u-boot. As per new cache management
framework,if the caches are not used in u-boot, it needs to be explicitly
indicated through macros in config file. CACHE disable is indicated by
the following macro definitions in config file,
1. CONFIG_SYS_ICACHE_OFF
2. CONFIG_SYS_DCACHE_OFF
3. CONFIG_SYS_L2CACHE_OFF
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Linus Walleij
Wolfgang Denk
Jason Jin
Christian Spielberger
Eric Benard
Joel Fernandes
Syed Mohammed Khasim
Jason Kridner
Koen Kooi
Koen Kooi
Steve Sakoman
Bob Feretich
Nagabhushana Netagunte
Manjunathappa, Prakash
Sudhakar Rajashekhara