With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a driver that supports Maxim 1 wire EEPROMs families
DS24B33 and DS2431.
Can be extended for other families as well.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked driver]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
When a new device is discovered, this may be a w1 eeprom device.
Attempt to find the proper node and driver from the w1-eeprom subsystem.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We might want to access data stored onto one wire EEPROMs.
Create a framework to provide a consistent API.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked patch]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add a bus driver for bitbanging a 1-Wire bus over a GPIO.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: fixed some issues]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We might want to use 1-Wire devices connected on boards such as EEPROMs in
U-Boot.
Provide a framework to be able to do that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This is file system generic loader which can be used to load
the file image from the storage into target such as memory.
The consumer driver would then use this loader to program whatever,
ie. the FPGA device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add a function to find the block device descriptor of the parent
device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
[trini: Move function declaration to avoid warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
Recently the FMan Port and MAC compatibles were changed. This patch
aligns the FMan Port and MAC compatibles to the new FMan device tree
binding document. The FMan device tree binding document can be found
in the Linux kernel version 3.18.0, commit
297d35fd2a7d3fbd4e5c0f0c1c18213117ba11ba
./Documentation/devicetree/bindings/powerpc/fsl/fman.txt
This patch doesn't affect legacy compatibles support.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Enable support for ICID setup of qman portals and the required device
tree fixups.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Memory reserved for Management Complex needs to be cleaned before any
usage.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add ahci compatible support for ls1021a soc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At present the MMC subsystem maintains its own list of MMC devices.
This cannot work with driver model when CONFIG_BLK is enabled, use
blk_dread to replace previous mmc read interface, use
mmc_get_blk_desc to get the mmc device property.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Based on dt-specs fixed-link doesn't require phy-handle to be used.
Fix driver to only read phy related setting when phy-handle is found.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
max-speed property is part of phynode and it has to be
read using ofnode_read_u32_default(). This fixes the issue
of incorrect max-speed read from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch modifies PL bitstream loading sequence as per
latest Xilfpga which supports all variants of bitstream images
generated from vivado and from bootgen. With this new change in
Xilfpga, uboot doesn't need to validate and swap bitstream as it will
be taken care inside Xilfpga. ZynqMP PL driver now checks for supporting
PMUFW version before skipping the validation and swap sequence as there
can be old PMUFW which doesn't supports this feature. In this case, driver
uses old way of PL bitstream loading sequence.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
AM654 uses a UART controller that is compatible (partially) with
existing OMAP UART, Introduce a compatible for adding support
for this controller.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When using device model this sort of hardcoded limits aren't used or
necessary.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
The loop in ahci_start_ports() is looping over the maximum number of
SCSI devices in the system, which can be larger than the amount of ports
a particular AHCI controller has. The extra looping isn't directly
harmful because the link_port_map bitmap won't have the bit set for a
nonexistent port, but it is wasteful. Replace the loop limit with the
port count of the AHCI controller instead.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
The MMC card detect pin is connected to gpio127 on omap3_logic.
When setting up the pbias register for MMC, let's also enable
gpio_127 for the card detect. As part of the package deal,
gpio_126 and gpio_129 are also enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
This adds support for the ARM PL022 SPI controller for the standard
variant (0x00041022) which has a 16bit wide and 8 locations deep TX/RX
FIFO.
A few parts were borrowed from the Linux kernel driver.
Cc: Armando Visconti <armando.visconti@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
On some boards using TI CPSW, it may be possible that
PHY address was not latched correctly, and the actual
address that the phy responds on is different from that
set in device-tree. For example, see this problem report
on beaglebone black:
https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J
Add support to check for this condition and use the
detected phy address when its safe to do so.
Also, add a public API that exposes the phy address of
a given slave. This can be used to update device-tree that
is passed to Linux kernel.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With this patch, PL031 driver is converted to driver-model-compliant
driver. In addition, CONFIG_SYS_RTC_PL031_BASE is no longer valid.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
CSI H can be used to position the cursor. The calling application may
specify a location that is beyond the limits of the screen. This may
lead to an illegal memory access.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
%s/efi_simple_input_interface/efi_simple_text_input_protocol/
We should be consistent in the naming of the EFI protocol interface
structures. The protocol is called EFI_SIMPLE_TEXT_INPUT_PROTOCOL.
%s/ExtendedVerification/extended_verification/
Use consistent naming of function parameters. Do not use CamelCase.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds support to Armada 7k/8k comphy RX/TX lane swap. The
'phy-invert' DT property defines the inverted signals.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
add delay before processing the status flags in pxa3xx_nand_irq().
Signed-off-by: David Sniatkiwicz <davidsn@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
c: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for NAND chips with 8KB page, 4 and 8 bit ECC (ONFI).
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add comments with timing parameter names and some details about
nand layout fileds.
Remove unneeded definition.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Replace the hardcoded value of page chink with value that
depends on flash page size and ECC strength.
This fixes nand access errors for 2K page flashes with 8-bit ECC.
Move the initial flash commannd function assignment past the ECC
structures initialization for eliminating usage of hardcoded page
chunk size value.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add timings and device ID for Toshiba TC58NVG1S3HTA00 flash
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for 2KB page 8-bit ECC strength flash layout
Signed-off-by: Victor Axelrod <victora@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
In the current driver, OOB bytes are accessed in raw mode, and when a
page access is done with NDCR_SPARE_EN set and NDCR_ECC_EN cleared, the
driver must read the whole spare area (64 bytes in case of a 2k page,
16 bytes for a 512 page). The driver was only reading the free OOB
bytes, which was leaving some unread data in the FIFO and was somehow
leading to a timeout.
We could patch the driver to read ->spare_size + ->ecc_size instead of
just ->spare_size when READOOB is requested, but we'd better make
in-band and OOB accesses consistent.
Since the driver is always accessing in-band data in non-raw mode (with
the ECC engine enabled), we should also access OOB data in this mode.
That's particularly useful when using the BCH engine because in this
mode the free OOB bytes are also ECC protected.
Fixes: 43bcfd2bb24a ("mtd: nand: pxa3xx: Add driver-specific ECC BCH support")
Cc: stable@vger.kernel.org
Reported-by: Sean Nyekjær <sean.nyekjaer@prevas.dk>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit is needed to properly support the 8-bits ECC configuration
with 4KB pages.
When pages larger than 2 KB are used on platforms using the PXA3xx
NAND controller, the reading/programming operations need to be split
in chunks of 2 KBs or less because the controller FIFO is limited to
about 2 KB (i.e a bit more than 2 KB to accommodate OOB data). Due to
this requirement, the data layout on NAND is a bit strange, with ECC
interleaved with data, at the end of each chunk.
When a 4-bits ECC configuration is used with 4 KB pages, the physical
data layout on the NAND looks like this:
| 2048 data | 32 spare | 30 ECC | 2048 data | 32 spare | 30 ECC |
So the data chunks have an equal size, 2080 bytes for each chunk,
which the driver supports properly.
When a 8-bits ECC configuration is used with 4KB pages, the physical
data layout on the NAND looks like this:
| 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 64 spare | 30 ECC |
So, the spare area is stored in its own chunk, which has a different
size than the other chunks. Since OOB is not used by UBIFS, the initial
implementation of the driver has chosen to not support reading this
additional "spare" chunk of data.
Unfortunately, Marvell has chosen to store the BBT signature in the
OOB area. Therefore, if the driver doesn't read this spare area, Linux
has no way of finding the BBT. It thinks there is no BBT, and rewrites
one, which U-Boot does not recognize, causing compatibility problems
between the bootloader and the kernel in terms of NAND usage.
To fix this, this commit implements the support for reading a partial
last chunk. This support is currently only useful for the case of 8
bits ECC with 4 KB pages, but it will be useful in the future to
enable other configurations such as 12 bits and 16 bits ECC with 4 KB
pages, or 8 bits ECC with 8 KB pages, etc. All those configurations
have a "last" chunk that doesn't have the same size as the other
chunks.
In order to implement reading of the last chunk, this commit:
- Adds a number of new fields to the pxa3xx_nand_info to describe how
many full chunks and how many chunks we have, the size of full
chunks and partial chunks, both in terms of data area and spare
area.
- Fills in the step_chunk_size and step_spare_size variables to
describe how much data and spare should be read/written for the
current read/program step.
- Reworks the state machine to accommodate doing the additional read
or program step when a last partial chunk is used.
This commit is taken from Linux:
'commit c2cdace755b'
("mtd: nand: pxa3xx_nand: add support for partial chunks")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit simplifies the initial configuration performed
by pxa3xx_nand_scan. No functionality change is intended.
This commit is taken from Linux:
'commit 154f50fbde53'
("mtd: pxa3xx_nand: Simplify pxa3xx_nand_scan")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The Data Flash Control Register (NDCR) contains two types
of parameters: those that are needed for device identification,
and those that can only be set after device identification.
Therefore, the driver can't set them all at once and instead
needs to configure the first group before nand_scan_ident()
and the second group later.
Let's split pxa3xx_nand_config in two halves, and set the
parameters that depend on the device geometry once this is known.
This commit is taken from Linux:
'commit 66e8e47eae65'
("mtd: pxa3xx_nand: Fix initial controller configuration")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The chunk size represents the size of the data chunks, which
is used by the controllers that allow to split transferred data.
However, the initial chunk size is used in a non-split way,
during device identification. Therefore, it must be large enough
for all the NAND commands issued during device identification.
This includes NAND_CMD_PARAM which was recently changed to
transfer up to 2048 bytes (for the redundant parameter pages).
Thus, the initial chunk size should be 2048 as well.
On Armada 370/XP platforms (NFCv2) booted without the keep-config
devicetree property, this commit fixes a timeout on the NAND_CMD_PARAM
command:
[..]
pxa3xx-nand f10d0000.nand: This platform can't do DMA on this device
pxa3xx-nand f10d0000.nand: Wait time out!!!
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x38
nand: Micron MT29F8G08ABABAWP
nand: 1024 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224
This commit is taken from Linux:
'commit c7f00c29aa8'
("mtd: pxa3xx_nand: Increase the initial chunk size")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The read ID count should be made as large as the maximum READ_ID size,
so there's no need to have dynamic size. This commit sets the hardware
maximum read ID count, which should be more than enough on all cases.
Also, we get rid of the read_id_bytes, and use a macro instead.
This commit is taken from Linux:
'commit b226eca2088'
("nand: pxa3xx: Increase READ_ID buffer and make the size static")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
When 2 commands are submitted in a row, and the second is very quick,
the completion of the second command might never come. This happens
especially if the second command is quick, such as a status read
after an erase
This patch is taken from Linux:
'commit 21fc0ef9652f'
("mtd: nand: pxa3xx-nand: fix random command timeouts")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
When the nand is first probe, and upon the first command start, the
status bits should be cleared before the interrupts are unmasked.
This commit is taken from Linux:
'commit 0b14392db2e'
("mtd: nand: pxa3xx_nand: fix early spurious interrupt")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Since the pxa3xx_nand driver was added there has been a discrepancy in
pxa3xx_nand_set_sdr_timing() around the setting of tWP_min and tRP_min.
This brings us into line with the current Linux code.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Don't store struct mtd_info in struct pxa3xx_nand_host. Instead use the
one that is already part of struct nand_chip. This brings us in line
with current U-boot and Linux conventions.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The initial buffer is used for the initial commands used to detect
a flash device (STATUS, READID and PARAM).
ONFI param page is 256 bytes, and there are three redundant copies
to be read. JEDEC param page is 512 bytes, and there are also three
redundant copies to be read. Hence this buffer should be at least
512 x 3. This commits rounds the buffer size to 2048.
This commit is taken from Linux:
'commit c16340973fcb64614' ("nand: pxa3xx: Increase initial buffer size")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Adam Ford
Eugen Hristev
Maxime Ripard
Tien Fong Chee
Ran Wang
Zhao Qiang
Pramod Kumar
Laurentiu Tudor
Prabhakar Kushwaha
Nipun Gupta
Peng Ma
Yinbo Zhu
Michal Simek
Siva Durga Prasad Paladugu
Lokesh Vutla
Tuomas Tynkkynen
Quentin Schulz
Sekhar Nori
AKASHI Takahiro
Heinrich Schuchardt
Philippe Reynes
Rabeeh Khoury
David Sniatkiwicz
Konstantin Porotchkin
Victor Axelrod
Boris Brezillon
Ofer Heifetz