Currently, if there is an error probing the NAND chip and the env is based
in NAND, the readenv() function will use a NULL function pointer and thus
jump to address 0.
Here I just check for a non-zero value of blocksize as that shouldn't be
zero when a valid device is found, but perhaps there is a better way for
someone familiar with the NAND internals to suggest.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
The "usb help" doesn't format the output correctly:
=> help usb
usb - USB sub-system
Usage:
usb reset - reset (rescan) USB controller
usb stop [f] - stop USB [f]=force stop
usb tree - show USB device tree
usb info [dev] - show available USB devices
usb storage - show details of USB storage devices
usb dev [dev] - show or set current USB storage device
usb part [dev] - print partition table of one or all USB storage devices
usb read addr blk# cnt - read `cnt' blocks starting at block `blk#'
to memory address `addr'usb write addr blk# cnt - write `cnt'
blocks starting at block `blk#' from memory address `addr'
=>
With fix below applied, the output is correct:
=> help usb
usb - USB sub-system
Usage:
usb reset - reset (rescan) USB controller
usb stop [f] - stop USB [f]=force stop
usb tree - show USB device tree
usb info [dev] - show available USB devices
usb storage - show details of USB storage devices
usb dev [dev] - show or set current USB storage device
usb part [dev] - print partition table of one or all USB storage devices
usb read addr blk# cnt - read `cnt' blocks starting at block `blk#'
to memory address `addr'
usb write addr blk# cnt - write `cnt' blocks starting at block `blk#'
from memory address `addr'
=>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
AM35x supports only 32bit read operations so we need to have
workaround for 8bit and 16bit read operations.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Adding general register structure of system control module (SCM)
of AM35x. This would be required to access devconf2 and ip_sw_reset
register in musb module.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
The bi_cpu field of the board data is already set to the relevant cpu
string, so there is no need for us to use the define directly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Recent features enabled by default require a larger monitor size for the
cm-bf548 port, so bump it up a bit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In case there is no frame buffer driver present in Linux to hand over the
PPI LCD DMA upon boot, the DMA initiated by u-boot to display the splash
screen runs unattended. Therefore always stop the video driver in u-boot
before starting Linux. If people don't want this behavior, then they can
simply stub out the video_stop() function in their board video driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Turn all ORION5X_DEF{ADR,SZ}_xxx macros into ORION5X_{ADR,SZ}_xxx
and allow defining them from board code to override defaults. This
is particularly useful for defining board-specific FLASH address
and size in board header file rather than having to tweak orion5x
code.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
get_timer_masked() should return current timestamp,
not current ticks from hardware register.
Tested on one custom board with NAND flash.
Without this patch, NAND write always TIMEOUT
because get_timer(0) return a big value.
This patch applies for u-boot-2010.06
Signed-off-by: Li Haibo <hbli@sinocastel.com>
Commit 6e37b1a3a25004d3df5867de49fff6b3fc9c4f04 modifies several net calls
to take a (const char *) parameter instead of (char *), but in some cases
the modified functions call other functions taking (char *). The end result
is warnings about discarding the const qualifier.
This patch fixes these other function signatures.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
For code that uses miiphy_{read,write}, every call invokes a full look up
of the mii list. There is already a "current_mii" cache that is used by
some code, but have the miiphy_{read,write} function use it as well. This
does increase the code size slightly, but I think it's worth it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Rather than have every func re-implement the list walking code, do it one
local function. This shrinks the resulting object code a little while
making the source much more manageable.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The driver name does not need to be writable, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8
"net ppc: fix ethernet device names with spaces" (currently in
u-boot-net.git) for QE based parts.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
since commit 1384f3bb8a ethernet names
with spaces drop a
Warning: eth device name has a space!
message. This patch fix it for:
- "FEC ETHERNET" devices found on
mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
renamed to "FEC".
- "SCC ETHERNET" devices found on
mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
boards. Renamed to "FCC"
Tested on the kup4k board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
After discussion on the ML it is suggested to drop unrequired
and not useful characters from the device name.
This patch changes the name for the fec_mxc driver from
"FEC_MXC" to "FEC".
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch has the following fixes/changes:
- Set 'kernel_addr' and 'ramdisk_addr' to correct values and add
'fdt_addr' environment variable
- Remove 'kozio' environment variable
- Remove environmant variables to boot ancient arch/ppc Linux kernels
- Remove CONFIG_SYS_BOOTMAPSZ definition. It's already defined to
the same value in amcc-common.h
Signed-off-by: Stefan Roese <sr@denx.de>
Update image size and default environment
after addition of new environment handling.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Update image size after addition of new environment handling.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Update image size after addition of new environment handling.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
None of the AMCC boards uses an embedded environment, so there is no
need to run "saveenv" after updating U-Boot. Drop the redundant
commands from the default environment.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Simply trying to include a basic header file like stdlib.h on OS X 10.5
and then building with -traditional-cpp fails with lots of errors like:
In file included from /usr/include/stdlib.h:63,
from test.c:3:
/usr/include/available.h:85: error: stray '#' in program
/usr/include/available.h:85: error: syntax error before numeric constant
/usr/include/available.h:86: error: stray '#' in program
In the past, I hadn't noticed because the old logic for these flags were
restricted to Darwin running on PowerPC systems while I'm running on an
Intel system. But after some recent clean ups and changes, the flag was
being applied to all Darwin systems and my host tools broke.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Original bug description from Feng (fdt_resize() bug caused "WARNING:
could not set linux, initrd-start FDT_ERR_NOSPACE."):
What I got is an error: "WARNING: could not set linux,initrd-start
FDT_ERR_NOSPACE." after loading Device Tree blob. This in turn caused
linux to miss init part.
After some digging, I found out the reason for this error, it is caused
by fdt_resize().
FDT blob got resized after filling in all board specific information of
PowerPC. (in boot_body_linux()). It reduced blob size with only extra
space for two fdt_reserve_entry, one for fdt itself, and one for initrd.
Then it's aligned to a 0x1000 page boundary. However, later in
fdt_initrd(), it could add two more properties, initrd-start AND
initrd-end, each one needs at least two fdt_reserve_entry sizes done by
_fdt_add_property() (name and value). Thus, the two fdt_reserve_entry
extra space is not sufficient.
So for some specific fdt size which is just under the page boundary
after resizing, this will cause an error of FDT_ERR_NOSPACE in
fdt_initrd() when setting those two properties, and failed to pass
initrd information to linux.
My fix is in fdt_resize(), leave at least 4 fdt_reserve_entry for
initrd. So instead of 2*sizeof(struct fdt_reserve_entry) for
actual_totalsize, use 5*sizeof(struc fdt_reserve_entry).
Stefan: I got this same error on katmai, when trying to boot with
initrd (run flash_self). This patch fixes this issue.
Signed-off-by: Feng Wang <fwang02@harris.com>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Most of the files have U_BOOT_CMD on a separate line,
but a few didn't and had the first line on the same line
as U_BOOT_CMD.
This changes these files by adding a line break and a tab
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
removed the command name from the help message as it is already printed.
for cmd_mmc also rewrote the message a little bit
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
The invalidation of the old environment instance did not work for flashes
supporting hardware locking. Now we unlock/lock around this update also.
Signed-off-by: Detlev Zundel <dzu@denx.de>
If a flash is unable to be detected, and then someone calls flash_protect
on it (like the common code does in flash_init), the flash_protect logic
will dereference a NULL pointer.
Since flash_protect already does sanity checking on the info structs, add
a NULL pointer check in there.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fix error handling in getenv_f() when the user provided buffer is too
short to hold the variable name; make sure to truncate and
NUL-terminate without overwriting the buffer limits.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Applying a little creative format string allows us to shrink the initial
data read & display loop by only calling printf once. Re-using the local
data buffer to generate the string we want to display then allows us to
output everything with just one printf call instead of multiple calls to
the putc function.
The local stack buffer needs increasing by 1 byte, but the resulting code
shrink and speed up is worth it I think.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
No need to output spaces 1 char at a time in a loop when the printf code
can do the same thing with the right format string. This shrinks things
and gives a nice speed up when killing off lines more than a byte or two
as printf will send out the buffer in one big chunk.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Kim Phillips
Mike Frysinger
Wolfgang Denk
Sergei Poselenov
Ajay Kumar Gupta
Michael Hennerich
Sergei Trofimovich
Albert Aribaud
Li Haibo
Reinhard Meyer
Ben Warren
Heiko Schocher
Stefano Babic
Stefan Roese
Heiko Schocher
Matthias Fuchs
Marek Vasut
Feng Wang
Frans Meulenbroeks
Detlev Zundel