The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update the sys_eeprom.c file to handle both NXID and CCID EEPROM formats. The
NXID format replaces the older CCID format, but it's important to support both
since most boards out there still use the CCID format. This change is in
preparation for using one file to handle both formats. This will also unify
EEPROM support for all Freescale 85xx and 86xx boards.
Also update the 86xx board header files to use the standard CFG_I2C_EEPROM_ADDR
instead of ID_EEPROM_ADDR.
Signed-off-by: Timur Tabi <timur@freescale.com>
Add function of new PCI, pci_skip_dev and pci_print_dev.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The L2_INIT_RAM option was unused, and recent changes to the TLB code
meant that the INIT_RAM TLBs weren't being cleared out. In order to reduce
the amount of mapped space attached to nothing, we change things so the TLBs
get cleared.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The fake flash bank was generating errors for anyone who didn't have a
PromJET hooked up to the board. As that constitutes the vast majority of
users, we remove it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The L2 size detection code was a bit confusing and we kept having to add
code to it to handle new processors. Change the sense of detection so we
look for the older processors that aren't changing.
Also added support for 1M cache size on 8572.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This was proposed by Paul Gortmaker in response to Wolfgang's comments on
similar #defines in sbc8560.h.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add in the default fdt settings and the typical EXTRA_ENV
settings as borrowed from the mpc8560ads. Fix a couple
of stale references to the mpc8560ads dating back to the
original clone/fork.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add in for the sbc8560, the ft_board_setup() routine, based on what is
in use for the Freescale MPC8560ADS board.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The existing config doesn't define CONFIG_HAS_ETH0, and so the
fdt support doesn't update the zeros in the dtb local-mac with
real data from the u-boot env. Since the existing config is
tailored to just two interfaces, get rid of the ETH2 definitions
at the same time.
Also don't include any end user specific data into the environment
by default -- things like MAC address, network parameters etc. need
to come from the end user.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The sbc8560 board ships with 512MB of memory installed,
but the current cs0_bnds is hard coded for 256MB. Set the
value based on CFG_SDRAM_SIZE.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The definitions for the TSEC have become out of date. There is no
longer any such options like "CONFIG_MPC85xx_TSEC1" or similar.
Update to match those of other boards, like the MPC8560ADS.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Some boards that have external 16550 UARTs don't have a direct
tie between bi_busfreq and the clock used for the UARTs. Boards
that do have such a tie should set CFG_NS16550_CLK to be
get_bus_freq(0) -- which most of them do already.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
With a page size of BOOKE_PAGESZ_16M, both the real and effective
addresses must be multiples of 16MB. The hardware silently truncates
them so the code happens to work. This patch clarifies the situation
by establishing addresses that the hardware doesn't need to truncate.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Delete the crypto node if not on an E-processor. If on 8360 or 834x family,
check rev and up-rev crypto node (to SEC rev. 2.4 property values)
if on an 'EA' processor, e.g. MPC8349EA.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The 8544 DS doesn't have any cacheable Local Bus memories set up. By mapping
space for some anyway, we were allowing speculative loads into unmapped space,
which would cause an exception (annoying, even if ultimately harmless).
Removing LBC_CACHE_BASE, and using LBC_NONCACHE_BASE for the LBC LAW solves the
problem.
Signed-off-by: Andy Fleming <afleming@freescale.com>
We need to wait while drawing engine clears frame
buffer before any further software accesses to frame
buffer will be initiated. Otherwise software drawn
parts could be partially destroyed by the drawing
engine or even GDC chip freeze could occur (as
observed on socrates board).
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Clean Makefile
Move device specific values to driver for better reading
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefan Roese <sr@denx.de>
Microblaze and PowerPC use boot_get_ramdisk for loading
ramdisk to memory with checking return value.
Return 0 means success. Return 1 means failed.
Here is correspond part of code from bootm.c which check
return code.
ret = boot_get_ramdisk (argc, argv, images, IH_ARCH_PPC,
&rd_data_start, &rd_data_end);
if (ret)
goto error;
Signed-off-by: Michal Simek <monstr@monstr.eu>
Redesign uartlite driver to in_be32 and out_be32 macros
Fix missing header in io.h
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Jean-Christophe PLAGNIOL-VILLARD
Wolfgang Denk
Andre Schwarz
Timur Tabi
Nobuhiro Iwamatsu
Andy Fleming
Kumar Gala
Paul Gortmaker
Andrew Klossner
Kim Phillips
Hugo Villeneuve
Anatolij Gustschin
Michal Simek
Marcel Ziswiler