The AMCC Luan now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
This patch also enables the cache in FLASH for the startup
phase of U-Boot (while running from FLASH). After relocating to
SDRAM the cache is disabled again. This will speed up the boot
process, especially the SDRAM setup, since there are some loops
for memory testing (auto calibration).
Signed-off-by: Stefan Roese <sr@denx.de>
The AMCC Yucca now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
Signed-off-by: Stefan Roese <sr@denx.de>
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the
DDR memory are dynamically programmed matching the total size
of the equipped memory (DIMM modules).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem that occurs when 2 DIMM's are
used. This problem was first spotted and fixed by Gerald Jackson
<gerald.jackson@reaonixsecurity.com> but this patch fixes the
problem in a little more clever way.
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
As this feature is new to the "old" 44x SPD DDR driver, it
has to be enabled via the CONFIG_PROG_SDRAM_TLB define.
Signed-off-by: Stefan Roese <sr@denx.de>
As provided by the AMCC applications team, this patch optimizes the
DDR2 setup for 166MHz bus speed. The values provided are also save
to use on a "normal" 133MHz PLB bus system. Only the refresh counter
setup has to be adjusted as done in this patch.
For this the NAND booting version had to include the "speed.c" file
from the cpu/ppc4xx directory. With this addition the NAND SPL image
will just fit into the 4kbytes of program space. gcc version 4.x as
provided with ELDK 4.x is needed to generate this optimized code.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the recently added Katmai board support. The biggest
change is the support of ECC DIMM modules in the 440SP(e) SPD DDR2
driver.
Please note, that still some problems are left with some memory
configurations. See the driver for more details.
Signed-off-by: Stefan Roese <sr@denx.de>
- fix logic error in image type handling
- make sure file system images (cramfs etc.) get stored in flash
with image header stripped so they can be mounted through MTD
Since the relocation fix is not included yet and we're not sure how
it will be added, this patch removes code that required relocation
to be fixed for now.
Signed-off-by: Stefan Roese <sr@denx.de>
As suggested by Grant Likely this patch enables the Xilinx SystemACE
driver to select 8 or 16bit mode upon startup.
Signed-off-by: Stefan Roese <sr@denx.de>
Some CPUs like PPC, BLACKFIN need sync() to ensure cfi flash write command
is fully finished. The sync() is defined in each CPU's io.h file. For
those CPUs which do not need sync for now, a dummy sync() is defined in
their io.h as well.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
This patch enables the "new" get_dev() function for block devices
introduced by Grant Likely to be used on systems that still suffer
from the relocation problems (manual relocation neede because of
problems with linker script).
Hopefully we can resolve this relocation issue soon for all platform
so we don't need this additional code anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes some problems when the Xilinx SystemACE driver
is used with 16bit access on an big endian platform (like the
AMCC Katmai).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch switches to the desired I2C bus when the date/dtt
commands are called. This can be configured using the
CFG_RTC_BUS_NUM and/or CFG_DTT_BUS_NUM defines.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the DDR2 controller used on the
440SP and 440SPe. It is tested on the Katmai (440SPe) eval
board and works fine with the following DIMM modules:
- Corsair CM2X512-5400C4 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5/512 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5K2/2G (1GByte per DIMM)
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Since the existing 4xx SPD SDRAM initialization routines for the
405 SDRAM controller and the 440 DDR controller don't have much in
common this patch splits both drivers into different files.
This is in preparation for the 440 DDR2 controller support (440SP/e).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for multiple I2C busses on the PPC4xx
platforms. Define CONFIG_I2C_MULTI_BUS in the board config file
to make use of this feature.
It also merges the 405 and 440 i2c header files into one common
file 4xx_i2c.h.
Also the 4xx i2c reset procedure is reworked since I experienced
some problems with the first access on the 440SPe Katmai board.
Signed-off-by: Stefan Roese <sr@denx.de>
Block device read/write is anonymous data; there is no need to use a
typed pointer. void * is fine. Also add a hook for block_read functions
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Register read/write does not need to be wrapped in a full function. The
patch replaces them with macros.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The code in this file is not a command; it is a device driver. Put it in
the correct place. There are zero functional changes in this patch, it
only moves the file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch is in preparation of additional changes to the sysace driver.
May as well take this opportunity to fixup the inconsistent whitespace since
this file is about to undergo major changes anyway.
There are zero functional changes in this patch. It only cleans up the
the whitespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Printing a buffer is a darn useful thing. Move the buffer print code
into print_buffer() in lib_generic/
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Change the xilinx device drivers and board code to include config.h
instead of xparameters.h directly. config.h always includes the
correct xparameters file. This change reduces the posibility of
including the wrong file when adding a new xilinx board port
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Each of the filesystem drivers duplicate the get_dev routine. This change
merges them into a single function in part.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update / extend Software Update Mechanism for MCC200 board:
- Add support for rootfs image added. The environment variables
"rootfs_st" and "rootfs_nd" can be used to override the default
values of the image start and end.
- Remove excessive key check code.
- Code cleanup.
Wolfgang Denk
Stefan Roese
Wolfgang Denk
Sergei Poselenov
Haiying Wang
Grant Likely