Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.
Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The SW output of the PMIC supplies the ethernet PHY with power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
DLDO3 is used to provide Port-D power and PD is used for the
usb-hub / sata-5v enable pins. The 2.5V comes from the schematic
and matches the factory image fex file.
The dts changes are the minimal changes needed for u-boot to
pick-up the usb host controllers. The upstream kernel does not
(yet) have usb host support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is the value used in the fex file of the manufacturer images,
and also the DCDC1 default. Sometimes lower values are used to save
battery power, but that does not apply to a SBC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Kconfig default settings are same as mentioned Sinovoip
Bpi-m3 schematic.
As axp818 ALDO support is enabled, it causes bpi-m3 fail to boot
if ALDOs are set to 0.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add dts and defconfig for Banana-pi M3 board.
It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI,
mic, AP6212 Wifi, etc on it.
It is paired with AXP813 PMIC which is almost same as AXP818.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add dts and defconfig for h8homletv2 board.
H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.
A83T patches are tested on this board.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede
Chen-Yu Tsai
Tom Rini
vishnupatekar
Simon Glass