This adds an option to force the size of the ram, and
avoid the detection of ram size.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The only platform left for the AU1x00 SoCs was the pb1x00 platform, an
apparent clone of the dbau1x00 platform. As pb1x00 had no listed
maintainer I am assuming that it is also orphaned. Remove this platform
and then remove the unused SoC support.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This platform has been marked as orphan since June of 2016 and should
have been removed some time ago. Do so now.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add a flash node to fix the detection of the memory IC.
With the changes introduced with commit 8fee8845e7
("enf_sf: reuse setup_flash_device instead of open coding it")
the SPI speed is now read from device-tree or a default value
is applied. This replaced the old behavior of setting the
SPI speed to CONFIG_ENV_SPI_MAX_HZ.
As this board didn't have a flash node, the default value
was applied to the SPI speed, producing an error when probing
the flash memory (speed too slow).
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for reading label property from DT and set up bank name
based on that. If label property is not present full device node name is
used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
.set_value functions have no specified return value and gpio_uclass is
not working with it too. But this patch is returning 0 to be in sync
with others DM gpio drivers.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Reading registers for finding out output value is not working because
input value is read instead in case of tristate.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
These functions are only called in this file that's why make them static
to keep static analysers happy.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to do read/write for if/else separately.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Set a value before changing gpio direction. This will ensure that the
old value is not propagated when direction has changed but new value is
not written yet.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Call xilinx_gpio_get_bank_pin() before use.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
CONFIG_MTD_DEVICE is required for the mtdparts command and but it is missing from the mvebu_armada-37xx.h
CONFIG_MTD_PARTITIONS is needed for the ubi support. Some of the Marvell based devices may require this as well.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
When kwboot is attached to a terminal which disappears such as one
connected via an unplugged USB cable, read() returns 0, making kwboot
loop until a key is pressed in the terminal. The only case where read()
may return 0 here is when the terminal is closed anyway, so let's
properly handle this one and report is similar to other errors.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 84899e2 ("tools/kwboot: Sync with latest barebox version to
support Armada XP") accidently broke the terminal-only mode (-t) by
removing the test on the bootmsg. Thus even when trying to use kwboot
as a plain terminal, it asks to reboot the target.
This commit simply reintroduces the lost test so that it is possible
again to use kwboot to attach to the target system's console.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This is required so SPL and u-boot can boot from spi
flash devices that use the dm drivers.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use -u-boot.dtsi]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The same pinctrl node appears in the solidrun-microsom dtsi. Use that
instead.
Cc: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
This makes changes so the u-boot dts file is structured more
similar to the mainline linux dtsi file. It provides a minimal
common dts that can work for most boards based on the ClearFog
platform. Ethernet support is only supported for eth0 however
all devices are left enabled so u-boot can generate and
provide mac addresses for all of the network interfaces.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: rebase on recent changes]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
Use hardware description from the recently introduced microsom .dtsi
file to reduce duplication.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
Add the "spi-flash" compatible string so that the generic sf_probe
driver can probe the SPI flash on the SolidRun SOM.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that there is DM support in the RTC_MV driver update board configs
to use it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To aid in migrating CONFIG_RTC_MV to Kconfig move the definition of it
from mv-plug-common.h to the board config headers that nest it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add the PCA9646 support, which is 2-wire bus switch and buffered 4-channel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This allows selection of the boot device at build time without source
code modification.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The kwboot utility can use the generated image to boot mvebu SoCs from
UART.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the gdsys Controlcenter DC specific build time kwbimage.cfg
generation code into the mach-mvebu/ directory to be shared by all 32bit
mvebu platforms.
Remove board specific kwbimage.cfg files, and use the generated one
instead. These files are all identical, with two exceptions. Clearfog
and Helios4 use the sdio boot device, whereas all others use spi. Update
the defconfigs for the exceptional boards to generate the same
kwbimage.cfg as before.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Use MVEBU_SPL_BOOT_DEVICE_* to select between SPI and MMC, instead of
board specific symbols. This commit enables the boot device selection
menu to all mvebu platforms, but it is only effective on Turris Omnia
and gdsys Controlcenter DC platforms. A following commit will enable
boot selection for other platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Use generic mvebu Kconfig symbols like all other mvebu boards.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
u-boot-spl.bin and u-boot-spl-dtb.bin are identical when building the
turris_omnia_defconfig. This commit makes Turris Omnia consistent with
all other mvebu boards.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This is to test power_domain_on in device_probe.
If the device has a power-domain property, enable it
when probe the device. So add the test to check
whether it is powered on or not.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add CONFIG_SPL_POWER_DOMAIN config entry.
Build drivers/power/domain if this config is selected.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add dummy functions when CONFIG_POWER_DOMAIN not defined.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files
and point to origin internal board name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves the the config SYS_MALLOC_LEN to
Kconfig. It will be just for Zynq arch and to do
will be for all other archs.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch used platdata structure instead of priv for storing static
information read from DT.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This issue is reported by kconfiglib:
warning: style: quotes recommended around default value for string
symbol XILINX_MICROBLAZE0_HW_VER (defined at
board/xilinx/microblaze-generic/Kconfig:37)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mini cse NOR configuration is running without PL that's why there is no
reason to enable clock to PL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing clocks property with fix clock-names property to be aligned
with emmc0 configuration and binding doc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Philippe Reynes
Tom Rini
Luis Araneda
Michal Simek
Vladimir Vid
Willy Tarreau
Chris Packham
Jon Nettleton
Baruch Siach
Peng Fan
Siva Durga Prasad Paladugu
Vipul Kumar