Remove blackfin specific implementation of the generic serial API when
early print macro is defined.
In BFIN_BOOT_BYPASS mode, don't call generic serial_puts, because
early print in bypass mode is running before code binary is relocated
to the link address.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
There may be dirty data in RDBR, so we should discard invalid data.
This operation also clears RXS bit in STAT register.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
BF5xx rx dma causes spi flash random read error.
Accually spi controller has problems both on tx and rx dma.
So remove spi dma support in u-boot.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
- Disable NAND driver on bf537-stamp.
- Make MMC_SPI optional.
- Disable LCD driver on bf527-ezkit.
- Enlarge BF609 nor flash reserved size from 256k to 512k bytes.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Add softswitch_output command for bf609-ezkit to enable softswitches.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Set up soft switch pins properly in board init code.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
The early serial should not be configured again in initcode() for BYPASS
boot mode and in start() for the other LDR boot modes.
In BYPASS boot mode, the start up code is located in Nor flash address other
than the DRAM address defined in link script. The code embedded string can't
be addressed by its compile time symbol. Calculate it according to the flash
offset.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Calculate the early uart clock from the system clock registers set by
the bootrom other than the predefine uboot clock macros.
Split the early baudrate setting function and the normal baudrate
setting one.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Define core 1 L1 code sram start address.
Add function to enable core 1 for BF609 and BF561.
Add config macro to allow customer to run core 1 in uboot init code on core 0.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Newer gcc versions will sometimes use a Preg when "r" constraints, but
that'll fail if we use an Ireg in the assignment. So force the code
to always use a Dreg.
This also fixes early boot crashes for older Blackfin parts when compiled
with gcc-4.5. This version ends up selecting the same register for the
input and output variables which corrupts the output assignment triggering
an exception.
P2 = 0xffe02008; /* EVT2 */
R0 = RETS;
CALL 1f;
RTN;
1: P2 = RETS; <-- BAD
RETS = R0;
[P2] = P2; <-- BAD
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Enable VIDEO and NAND supports only when the config options is defined.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
The define should not have been put in fdt.h originally, libfdt_env.h
is the proper place for target-specific customizations.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This commit adds a license header to fdt.h and libfdt_env.h
because the license was omitted.
U-Boot note: the u-boot libfdt_env.h header portion was not applied to
the u-boot libfdt_env.h because that file was created by Gerald Van Baren
(with a license header). - gvb
Ref: DTC commit 27cdc1b1
Signed-off-by: Justin Sobota <jsobota@ti.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This function is useful outside libfdt, so export it.
Ref: DTC commit b7aa300e
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Since there are two memory areas defined, vectors and ram,
the linker will error when neither of them are specified for a
section.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
The 512 byte block size was hard coded in the ext4 file systems.
Large harddisks today support bigger block sizes typically 4096
bytes.
This patch removes this limitation.
Signed-off-by: Egbert Eich <eich@suse.com>
Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them. Also fix reference to doc/README.SPL file.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Patman requires python 2.7.4 to run but it doesn't
need to be placed in /usr/bin/python.
Use env to ensure that the interpreter used is
the first one on environment's $PATH on system
with several versions of Python installed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Conflicting tags can prevent buildman from building two series which exist
one after the other in a branch. There is no reason not to allow this sort
of workflow with buildman, so ignore conflicting tags in buildman.
Change-Id: I2231d04d8684fe0f8fe77f8ea107e5899a3da5e8
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
If the environment contains an entry like "=value" "\0" we should throw
an error when parsing the environment. Otherwise, U-Boot will enter in
an infinite loop.
Signed-off-by: Lucian Cojocar <cojocar@gmail.com>
Currently the base setting for CFLAGS is split in two possibilities,
one with -DBUILD_TAG appended at the end and one without, the rest of
CFLAGS is the same in both cases. Change this so CFLAGS are always set
and the -DBUILD_TAG is appended in separate ifdef.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Microblaze uses gpio which is connected to the system reset.
Currently gpio subsystem wasn't used for it.
Add gpio driver and change Microblaze reset logic to be done
via gpio subsystem.
There are various configurations which Microblaze can have
that's why gpio_alloc/gpio_alloc_dual(for dual channel)
function has been introduced and gpio can be allocated
dynamically.
Adding several gpios IP is also possible and supported.
For listing gpio configuration please use "gpio status" command
This patch also remove one compilation warning:
microblaze-generic.c: In function 'do_reset':
microblaze-generic.c:38:47: warning: operation on '*1073741824u'
may be undefined [-Wsequence-point]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
fdt_initrd add additional information to DTB about initrd
addresses which are later used by kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Include this header to get access to link symbols, which are otherwise
removed.
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
A malloc() followed by memset() can be simply replaced by calloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If failed the add_host(), it is reasonable that return value of
add_sdhci().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Without this additional delay, some eMMC don't negotiate properly bus width
Tested on:
- Toshiba THGBM2G8D8FBAIB
- Toshiba THGBM4G4D1HBAR
- Micron MTFC4GMVEA (the one giving the problem)
- Hynix H26M64002BNR
- SanDisk SDIN5E1-32G
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Most of time that MMC driver spends on initializing a device is polling
OCR (operation conditions register). To decouple this polling loop,
device init is split into two parts: The first part fires the OCR query
command, and the second part polls the result. So the caller is now no
longer bound to the OCR-polling delay; he may fire the query, go
somewhere and then come back later for the result.
To use this, call mmc_set_preinit() on any device which needs this.
This can save significant amounts of time on boot (e.g. 200ms) by
hiding the MMC init time behind other init.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We can use a common global method for calculating minimum of
3 numbers. Put the same in 'common header' and let 'ehci'
use it.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Fix the Port status bit constants and Port feature number
constants as a part of USB 2.0 and USB 3.0 Hub class.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Untill now we power-cycle (aka: disable power on a port
and re-enabling again) one port at a time.
Delay of 20ms for Port-power to change multiplies with
number of ports in this case.
So better we parallelize this process:
disable power on all ports, wait for port-power to stabilize
and then re-enable the power subsequently.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
This adds usb framework support for super-speed usb, which will
further facilitate to add stack support for xHCI.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Patch b6d7852c increases timeout for enumeration, taking
worst case to be 10 sec.
get_timer() api returns timestamp in milliseconds, which is
what we are checking in the do-while() loop in usb_hub_configure()
(get_timer(start) < CONFIG_SYS_HZ * 10).
This should give us a required check for 10 seconds, and thereby
we don't need to add additional mdelay of 100 microseconds in
each cycle.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Fetch the device class into usb device's dwcriptors,
so that the host controller's driver can use this info
to differentiate between HUB and DEVICE.
Signed-off-by: Amar <amarendra.xt@samsung.com>
XHCI ports are powered on after a H/W reset, however
EHCI ports are not. So disabling and re-enabling power
on all ports invariably.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Some cleanup in usb framework, nothing much on feature side.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
USB_PRINTF, USB_HUB_PRINTF, USB_STOR_PRINTF, USB_KBD_PRINTF
are nothing but conditional debug prints, depending on DEBUG.
So better remove them and use debug() simply.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Scott Jiang
Sonic Zhang
Bob Liu
Mike Frysinger
Gerald Van Baren
Justin Sobota
François Revol
Simon Glass
Tom Rini
Stefan Kristiansson
Egbert Eich
Anatolij Gustschin
Michal Simek
Lucian Cojocar
Marek Vasut
Kuan-Yu Kuo
Fabio Estevam
Jaehoon Chung
Vipin Kumar
Davide Bonfanti
Che-Liang Chiou
Vivek Gautam
Bo Shen