This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
this patch addresses the issue that there is no DVI output on beagleboard-xm in
u-boot; the TFP410 is not powered on, DVI_PUP needs to be set high
this is done differently on beagleboard-xm rev. B/C versus earlier boards:
beagleboard-xm B/C need to set GPIO2 of the TWL4030
earlier boards need to set GPIO170
note that the change occured somewhere inbetween beagleboard-xm rev. A2 and A3
note that beagleboard-xm rev. A and rev. B cannot be distinguished using
get_board_revision(), REVISION_XM_A/REVISION_XM_B is bogus
due to this glitch, the patch cannot work correctly on some beagleboard-xm
rev A/B boards
tested on beagleboard-xm rev. C (you should see orange color on a monitor)
note that the framebuffer is NOT yet set up, this could be done along the
lines below (for 800x480 resolution and RGB24) before calling omap3_dss_enable()
static void configure_frame_buffer() {
writel(0x80500000, (uint *) 0x48050480); // address
writel(0x80500000, (uint *) 0x48050484);
writel(0x01df031f, (uint *) 0x4805048c); // size
writel(0x00000091, (uint *) 0x480504a0); // RGB24
}
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Clean up added ehci-omap.c and make it generic for re-use across
omap-soc having same ehci ip block. Also pass the modes to be configured
from board file and configure the ports accordingly. All usb layers
are not cache aligned, till then keep cache off for usb ops as ehci will use
internally dma for all usb ops.
* Add a generic common header ehci-omap.h having common ip block
data and reg shifts.
* Rename and modify ehci-omap3 to ehci.h retain only conflicting
sysc reg shifts remove others and move to common header file.
* pass the board data for beagle/panda accordinly to use
ehci ports.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
The logic for the rev C4 boards was missing one of the cases
(variant with Micron NAND and 2x128MB).
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
This introduces 200MHz Micron parts timing information based on x-loader
to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation. The memory init
logic is also based on what x-loader does in these cases. Note that
while previously u-boot would be flashed in with SW ECC in this case it
now must be flashed with HW ECC. We also change CONFIG_SYS_TEXT_BASE to
0x80100000.
Cc: Dirk Behme <dirk.behme@gmail.com>
Beagleboard rev C5, xM rev A:
Tested-by: Tom Rini <trini@ti.com>
Beagleboard xM rev C:
Tested-by: Matt Ranostay <mranostay@gmail.com>
Beagleboard rev B7, C2, xM rev B:
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
gpio_free() should not have the side effect of setting the line to input since this prevents the gpio command from being able to set a line as output.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Read the led output state from GPIO instead saving state in memory when it is [re]set
* Added a toggle option to the led command
Previous discussion:
http://lists.denx.de/pipermail/u-boot/2011-May/093068.html
Changes since v1:
Fixed checkpatch errors
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fixed USR0/USR1 to be LED 0/1 respectively
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on patches from Syed Mohammed Khasim (khasim@ti.com).
Configures the output of the BeagleBoard DVI to be orange.
Configures the output of the BeagleBoard S-Video to be a colorbar.
Changed display_init to beagle_display_init as suggested by Igor Grinberg:
http://www.mail-archive.com/u-boot@lists.denx.de/msg51446.html
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on commit f1099c7c43caf5bac3bf6a65aa266fade4747072
Author: Greg Turner <gregturner@ti.com>
Date: Tue May 25 09:19:06 2010 -0500
New u-boot command for status of USER button on BeagleBoard-xM
Modified bootcmd to check the staus at boot time and set
filename of the boot script.
* Moved to a BeagleBoard specific file.
* Removed changes to default boot command from adding userbutton
command.
* Made to handle pre-xM boards.
* Flipped polarity of the return value to avoid confusion. Success (0)
is when the button is pressed. Failure (1) is when the button is NOT
pressed.
* Used latest revision getting function.
* Used latest macros for board revision.
* Added xM-C revision definition (optional, since it was default)
* updated default configuration with UserButton functionality
* Added a separate bootenv variable to load a user defined .txt file
* Added an example, showing how a different environment file can be loaded with
the user button pressed
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Greg Turner <gregturner@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This fixes display problems in linux
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The below patch reverses the order of two segments in the board file.
Output pins need to have their values initialized, before they are
exposed to the logic outside the chip.
Signed-off-by: Bob Feretich <bob.feretich@rafresearch.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The reset sequence/configuration for ehci is highly board specific,
so this will be done in the source for the board, instead of
introducing several CONFIG_* which would be needed to make those
few lines in beagle.c usable across different OMAP boards.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Patch was updated by Jason Kridner <jkridner@beagleboard.org>:
* Use tabs to match style of other board revisions
* Only include board revisions that exist
* Default to the same configuration as the latest revision, but
without setting 'beaglerev'
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This allows the reading of EEPROMS on the expansion bus without adding
external pull-ups.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added LED driver using status_led. USR0 is set to monitor the boot
status. USR1 is set to be the green LED.
Included adding configuration and command to the default configuration.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
Beagle expansion boards contain an i2c eeprom to identify themselves.
This patch adds code to read and parse the eeprom contents. It prints
the expansion board name and revision and modifies environment variables
as appropriate. This patch is based on the Overo expansion board code.
Signed-off-by: Koen Kooi <k-kooi@ti.com>
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds missing pinmux setup for 4 GPIO signals used on the Beagle xM:
- USB hub reset (gpio_56)
- P8 USB hub reset (gpio_63)
- DVI enable (gpio_129)
- P8 DVI enable (gpio_170)
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Change the implementation for ARM V7 to relocate the code to an
arbitrary address in RAM.
Adapt the Beagle board (Cortex A8) to test the changes.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds support for the Beagle xM. It uses the board ID
GPIO bits to recognize this revision and perform appropriate setup.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch enhances the revision detection function and adds
support for the C4 revision. The board revision is printed
and approriate revision specific setup is done automatically.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Not all boards have both LEDs hooked, so enabling both on
boards with single LED will just waste power. Make it
possible to choose LEDs by adding argument to
twl4030_led_init().
Using this turn on only LEDB for pandora, leave both LEDs
on for all other boards, as it was before this patch.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Switch from space-based indentation to tab-based in mux configs, as pointed
out by WD at:
http://lists.denx.de/pipermail/u-boot/2009-September/061241.html
Nothing but whitespace changes in this patch (diff -w gives no output).
Signed-off-by: Olof Johansson <olof@lixom.net>
Switch from space-based indentation to tab-based in mux configs, as pointed
out by WD at:
http://lists.denx.de/pipermail/u-boot/2009-September/061241.html
Nothing but whitespace changes in this patch (diff -w gives no output).
Signed-off-by: Olof Johansson <olof@lixom.net>
Simon Glass
Peter Meerwald
Govindraj.R
Ilya Yanok
robertcnelson@gmail.com
Tom Rini
Joe Hershberger
Mike Frysinger
Dirk Behme
Jason Kridner
Sanjeev Premi
Christian Spielberger
Joel A Fernandes
Koen Kooi
Bob Feretich
Wolfgang Denk
Alexander Holler
Steve Kipisz
John Rigby
Sebastien Carlier
Steve Sakoman
Heiko Schocher
Grazvydas Ignotas
Olof Johansson
Jean-Christophe PLAGNIOL-VILLARD