Currently sata usage text prints a double 'sata' for the init command.
MX53LOCO U-Boot > sata
sata - SATA sub system
Usage:
sata sata init - init SATA sub system
sata info - show available SATA devices
sata device [dev] - show or set current device
sata part [dev] - print partition table
sata read addr blk# cnt
sata write addr blk# cnt
Remove the extra 'sata' from the 'sata init' line.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This pulls the three following ZYNQ commits into ARM master:
7dca54f8: xilinx: zynq: Enable DCC and create new zynq_dcc board
59c651f4: arm: zynq: Add SLCR support with system reset
00ed3458: arm: zynq: Add lowlevel initialization to C
This target will move the environment into SPI flash and documents
the expected layout. We correct the SPL define for where U-Boot is
and remove an unused define.
Signed-off-by: Tom Rini <trini@ti.com>
Added README file with the description of required options and host
configuration to use network SPL with am335x targets. Briefly discuss
how to use this configuration to program empty boards.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
* Added variables to support SPI booting
* Note that the first 512KiB are reserved for 4 copies of SPL.
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
* Added support to the default environment variables for NAND
boot.
* Add nandboot to the default bootcmd.
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Rather than load the FPGA file from the FAT partition, look
at entry in system EEPROM to decide which file to retrieve directly
from the EXT3 partition.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Also, change bootdelay to 0 but allow pressing 'S' to stop at U-Boot prompt.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Howard Gray <howard.gray@matrix-vision.de>
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
The IGEP COM PROTON is a new ultra compact module design with an
on-board ethernet controller.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Current '#if' directives (used in igep00x0.h config file) comparing MACH_TYPE
values in igep00x0.h doesn't work as expected. The comparision between
CONFIG_MACH_TYPE and MACH_TYPE_IGEP0020 is always true independent of the IGEP
machine configured.
For example, following directive
if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020)
define something
endif
Is always evaluated true although we configure u-boot for MACH_TYPE_IGEP0030.
The build doesn't shows any error so looks that both defines had always the same
value. Including the mach-types.h file sets properly the value of
MACH_TYPE_IGEPxxxx.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
This adds necessary config options and a new build target,
am335x_evm_usbspl, to enable usb booting and fixes board_eth_init()
function to take into account that we may have USB ether support in SPL
now. This uses the same MAC for both cpsw and USB, in order to match
ROM behavior.
The usbspl build target does not contain UART SPL, CPSW SPL or extra
environment settings, so that we may fit within our binary size
constraint.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds BOOT_DEVICE define for USB booting and fixes
spl_board_init function to call arch_misc_init (this is the place there
musb is initialized).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
In case of usbeth booting just call net_load_image("usb_ether").
This patch also adds CONFIG_SPL_USBETH_SUPPORT and
CONFIG_SPL_MUSB_NEW_SUPPORT config options to enable linking of SPL
against USB gagdet support and new MUSB driver resp.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
The pcm051 does not have the wp pin connected to the sd-card socket.
Therefore remove the pinmux for the pin. The was a carry-over from
the am335x evm code.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
The pinmux was generated from linux/arch/arm/mach-davinci/da830.c as of
kernel version 3.7.5. If the driver is used for the da850, then SoC
variant must be specified by CONFIG_SOC_DA850.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: Tom Rini <trini@ti.com>
Remove the manual relocation of env_name_spec. This has been missed
in the previous patch series for introducing dynamic relocation
on MIPS.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This code is pretty old and we want to support only 32-bit systems now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
Invert the polarity of this option to simplify the Makefile logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Gabe Black <gabeblack@chromium.org>
These lines are dealt with in the x86 Makefile and link script, so punt
them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Gabe Black <gabeblack@chromium.org>
This x86 CPU variant is no longer required as the boards that use it have
been removed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
The code handles relocation entries with the
following relocation types only:
mips32: R_MIPS_REL32
mips64: R_MIPS_REL+R_MIPS_64
xburst: R_MIPS_REL32
Other relocation entries are skipped without
processing. The code must be extended if other
relocation types must be supported.
Add -pie to LDFLAGS_FINAL to generate the .rel.dyn
fixup table, which will be applied to the relocated
image before transferring control to it.
The CONFIG_NEEDS_MANUAL_RELOC is not needed
after the patch, so remove that as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This section contain the table needed for dynamic
relocation. Also provide symbols for the relocation
code to access the table.
Discard all sections which are not needed in the final
ELF binary and U-Boot image. Section .dynsym cannot be
discarded or GNU ld crashes otherwise. This section
will be stripped by GNU objcpy in a later patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Use the newly introduced symbol __image_copy_end as end address for
relocation of U-Boot image. This is needed for dynamic relocation added
in later patches. This patch obsoletes the symbols uboot_end and
uboot_end_data which are removed.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Get the start and end address for clearing BSS from the newly
introduced symbols __bss_start and __bss_end. After GOT is
relocated, those symbols are already pointing to the correct
addresses.
Also optimize the loop by moving the address incrementation
to the delay slot to avoid the initial sub instruction.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Use the newly introduced symbols __image_copy_end and __bss_end
for setting up the memory area for the relocated U-Boot.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This symbol is used in later patches as end address
for relocation of the U-Boot image into RAM.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
These symbols are used in later patches for as addresses for
clearing the BSS area in the relocated U-Boot image.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The '__got_start' and '__got_end' symbols are used
only in the linker script to compute the value of
the 'num_got_entries' symbol.
Remove the symbols and use the SIZEOF(.got) command
to get the size of the .got section.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Fix access to global_data which is broken since commits:
commit 035cbe99cd
Author: Simon Glass <sjg@chromium.org>
Date: Thu Dec 13 20:49:08 2012 +0000
mips: Move per_clk and dev_clk to arch_global_data
Move these field into arch_global_data and tidy up. The other
CONFIG_JZSOC fields are used by various architectures, so just remove
the #ifdef bracketing for these.
Signed-off-by: Simon Glass <sjg@chromium.org>
commit 582601da2f
Author: Simon Glass <sjg@chromium.org>
Date: Thu Dec 13 20:48:35 2012 +0000
arm: Move lastinc to arch_global_data
Move this field into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
commit 66ee692347
Author: Simon Glass <sjg@chromium.org>
Date: Thu Dec 13 20:48:34 2012 +0000
arm: Move tbl to arch_global_data
Move this field into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Xiangfu Liu <xiangfu@openmobilefree.net>
In commit cfd4ff6 we implemented part of advisory 1.0.10 (internal delay
for RGMII mode not supported). This in turn however requires that we
set the tx clock delay feature in the PHY itself.
Signed-off-by: Tom Rini <trini@ti.com>
In order to use the more thorough memory test, the macro
CONFIG_SYS_MEMTEST_SCRATCH must be defined with a usable
address.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The baudrate is already defined by CONFIG_BAUDRATE and there is no need
to keep CONFIG_SYS_BAUDRATE_TABLE.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
When calling 'make u-boot.imx' the build were failing as it were
expecting the full path for the file; this regression has been
included by commit 71a988a (imximage.cfg: run files through C
preprocessor).
The direct references for u-boot.imx were replaced by $(obj) as
config.mk handles the proper setting of it making it set to $(OBJTREE)
when required.
The build has been test using:
- ./MAKEALL -s mx5 -s mx6
- make u-boot.imx
- make O=/tmp/build
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
On a mx6qsabresd revision C board with rev1.2 mx6q, the system gets resetted
and it is not able to reach the Linux prompt.
Comparing the watchdog behaviour on a revB versus revC board:
- On a mx6qsabresd revB:
U-Boot > reset
resetting ...
U-Boot 2013.01-10524-g432a3aa-dirty (Feb 07 2013 - 13:34:46)
CPU: Freescale i.MX6Q rev1.1 at 792 MHz
Reset cause: WDOG
...
- On a mx6qsabresd revC:
U-Boot > reset
resetting ...
U-Boot 2013.01-10524-g432a3aa-dirty (Feb 07 2013 - 13:34:46)
CPU: Freescale i.MX6Q rev1.1 at 792 MHz
Reset cause: POR
So due to revC POR/watchdog circuitry whenever a watchdog occurs, it causes a POR.
Clearing the PDE - Power Down Enable bit of WMCR registers fixes the problem and
is also safe for all mx6 boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
All the users of mx6q_4x_mt41j128.cfg (DDR3-1333H Micron MT41J128M16HA-15E or SK
hynix H5TQ2G63BFR-H9C for i.MX6Q SABRE Lite, and DDR3-1600K Micron
MT41K128M16JT-125:K for i.MX6 SABRE SD) support the optional down binning to
DDR3-1066F (CL = 7, CWL = 6), which is possible at 532 MHz, so use it.
In these conditions:
tRCD(min) = 13.125 ns
tRP(min) = 13.125 ns
tRC(min) = max(tRAS(min, DDR3-1333H), tRAS(min, DDR3-1600K)) + tRP(min)
tRAS(min, DDR3-1333H) = 36 ns
tRAS(min, DDR3-1600K) = 35 ns
MMDC1_MDCFG0.tCL should be set to 7 nCK, encoded as 0x4 in the bit-field
MMDC1_MDCFG0[3:0].
MR0.CL should be set as in MMDC1_MDCFG0.tCL, i.e. to 7 nCK, which is encoded
as 0x6 in MRS.LMR.MR0.{A6:A4, A2} and MMDC1_MDSCR[22:20, 18].
MMDC1_MDCFG1.tCWL should be set to 6 nCK, encoded as 0x4 in the bit-field
MMDC1_MDCFG1[2:0].
MMDC1_MDCFG1.tRCD should be set to 13.125 ns, which is 7 nCK at 532 MHz, encoded
as 0x6 in the bit-field MMDC1_MDCFG1[31:29].
MMDC1_MDCFG1.tRP should be set to 13.125 ns, which is 7 nCK at 532 MHz, encoded
as 0x6 in the bit-field MMDC1_MDCFG1[28:26].
MMDC1_MDCFG1.tRC should be set to 49.125 ns, which is 27 nCK at 532 MHz, encoded
as 0x1A in the bit-field MMDC1_MDCFG1[25:21].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Fabio Estevam
Stefano Babic
Albert ARIBAUD
Tom Rini
Ilya Yanok
Chase Maupin
Michael Jones
Howard Gray
Enric Balletbo i Serra
Lars Poeschel
robertcnelson@gmail.com
Tomas Novotny
Daniel Schwierzeck
Simon Glass
Gabor Juhos
Eric Nelson
Otavio Salvador
Benoît Thébaudeau