Patch d873133f [ppc4xx: Add Sequoia RAM-booting target] broke "normal"
booting on some 44x platforms. This breakage is only noticed in some
cases while powercycling. As it seems, the code in question in start.S
didn't invalidate TLB #0. This makes sense since this TLB is used for
the bootrom mapping. With the patch mentioned above even TLB #0 got
invalidated resulting in an error later on.
This patch now fixes this issue by only invalidating TLB #0 in the RAM-
booting case.
Tested succesfully on Sequoia and Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <Eibach@gdsys.de>
The top build system sets up HOSTCFLAGS a bit and exports it, but other
places use HOST_CFLAGS instead. Unify the two as HOSTCFLAGS so that the
values stay in sync.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CSB337 boards originally shipped with MicroMonitor, not U-Boot;
and with a version using a different convention for recording
Ethernet addresses than anyone else. To avoid breaking Linux
when it uses U-Boot, have it use the same convention on that
hardware.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Because of the reset_cpu is soc specific, should be move to soc
Cc: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Previously, 85xx and 86xx boards would display DRAM information on
bootup such as:
...
I2C: ready
DRAM:
Memory controller interleaving enabled: Bank interleaving!
2 GB
FLASH: 256 MB
...
This patch moves the printing of the DRAM controller configuration to a
common board_add_ram_info() function which prints out DDR type, width,
CAS latency, and ECC mode. It also makes the DDR interleaving
information print out in a more sane manner:
...
I2C: ready
DRAM: 2 GB (DDR2, 64-bit, CL=4, ECC on)
DDR Controller Interleaving Mode: bank
FLASH: 256 MB
...
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rename sdram_mode_1 to sdram_mode and sdram_cfg_1 to sdram_cfg to match
the 86xx user's manual and other Freescale architectures
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Part of the mini Blackfin ABI with operating systems is that they can use
0x4f0-0x4f8 to pass log buffers to/from bootloaders. So add support to
U-Boot for reading the log buffer.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On build of omap3 targets in MAKEALL, the *.ERR files have
cpu.c: In function 'cleanup_before_linux':
cpu.c:64: warning: implicit declaration of function 'v7_flush_dcache_all'
cpu.c:64: warning: implicit declaration of function 'get_device_type
The functions v7_flush_dcache_all and get_device_type are declared
in include/asm-arm/arch-omap3/sys_proto.h, so use this file to
declare the functions.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
So far the console API uses the following naming convention:
======Extract======
typedef struct device_t;
int device_register (device_t * dev);
int devices_init (void);
int device_deregister(char *devname);
struct list_head* device_get_list(void);
device_t* device_get_by_name(char* name);
device_t* device_clone(device_t *dev);
=======
which is too generic and confusing.
Instead of using device_XX and device_t we change this
into stdio_XX and stdio_dev
This will also allow to add later a generic device mechanism in order
to have support for multiple devices and driver instances.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Remove individual CPU specific DSPI driver.
Add required feature for the common DSPI driver in cpu_init and
in platform configuration file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Update serial boot DRAM's Internal RAM, vector table and DRAM in
start.S, serial flash's read status command over SPI and NOR
flash.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Now that we have 3 boards for the MPC512x it turns out that they all
use the very same fixed_sdram() code.
This patch factors out this common code into cpu/mpc512x/fixed_sdram.c
and adds a new header file, include/asm-ppc/mpc512x.h, with some
macros, inline functions and prototype definitions specific to MPC512x
systems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Current code only sets the PCI vendor id to 0x1014 and
leaved device id to 0x0000.
Ths patch ....
a) uses the correct PCI_VENDOR_ID_IBM macro for this
b) sets the default device ID as stated in the UM to 0x0156
by using PCI_DEVICE_ID_IBM_405GP for this.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some basic PCI initialisation from the 4xx cpu_init_f()
to cpu/ppc4xx/4xx_pci.c.
The original cpu_init_f() function enabled the 405EP's internal arbiter
in all situations. Also the HCE bit in cpc0_pci is always set.
The first is not really wanted for PCI adapter designs and the latter
is a general bug for PCI adapter U-Boots. Because it enables
PCI configuration by the system CPU even when the PCI configuration has
not been setup by the 405EP. The one and only correct place is
in pci_405gp_init() (see "Set HCE bit" comment).
So for compatibility reasons the arbiter is still enabled in any case,
but from weak pci_pre_init() so that it can be replaced by board specific
code.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
It fixes the access to the 'ehci' struct elements for mpc83xx which
should have been taken care of in 4ef01010aa
Sorry about that.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch makes pll_write on PPC405EP boards
global and callable from C code.
pll_write can be used to dynamically modify the PLB:PCI divider
as it is required for 33/66 MHz pci adapters based on the 405EP.
board_early_init_f() is a good place to do that (check M66EN signal
and call pll_write() when it is required).
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch implements the is_pci_host() function in a similiar way
as it is used on 440 targets.
The former path with CONFIG_PCI_HOST == PCI_HOST_AUTO does not
build on 405EP targets because checking the PCI arbiter is different.
So putting the fixed code into a separate function makes the code
more readable.
Also using is_pci_host() on 405 brings 405 and 440 PCI code
a little bit closer.
In preparation for an upcoming 405EP based PMC module I made this
function weak so that it can be overwritten from board specific code.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a debug compilation error for PPC4xx platforms, all
other architectures are not affected by this change. The 'handler'
pointer was undefined. The fix is exercised and has effect only if
DEBUG is defined.
Signed-off-by: Alessio Centazzo acpatin@yahoo.com
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes printf format string compilation warnings in several
debug statements. It also fixes the dump of DDR controller MQ registers
found on some 44x and 46x platforms. The current register dump code
uses incorrect DCRs to access these registers.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
all sh boards use the same cpu linker script so move it to cpu/$(CPU)
that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk
tested on r2dplus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.
CAN is available on AT91SAM9263 and AT91CAP9 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The calculate for rank density in compute_ranksize() for DDR3 used all
integers for the expression, so the result was also a 32-bit integer, even
though the 'bsize' variable is a u64. Fix the expression to calculate a
true 64-bit value.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also update dmacpy()'s argument order to match memcpy's and use
phys_addr_t/phy_size_t for address/size arguments
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DMA support is now enabled via the CONFIG_FSL_DMA define instead of the
previous CONFIG_DDR_ECC
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Unify with 83xx and 85xx and use CPU_TYPE_ENTRY. We are going to use
this to convey the # of cores and DDR width in the near future so its
good to keep in sync.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Because of the reset_cpu is soc specific, should be move to soc
And read reset value from SYS_ID register instead of hard code
this patch also supports s3c6410
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Stefan Roese
Mike Frysinger
Ilya Yanok
David Brownell
Minkyu Kang
Peter Tyser
Tom Rix
Jean-Christophe PLAGNIOL-VILLARD
Valeriy Glushkov
TsiChung Liew
Wolfgang Denk
Sedji Gaouaou
Jon Smirl
Matthias Fuchs
Vivek Mahajan
Alessio Centazzo
Felix Radensky
Prafulla Wadaskar
Alessandro Rubini
Daniel Gorsulowski
Kim, Heung Jun
Timur Tabi
Kumar Gala
Magnus Lilja