Commit 054197ba and later fixes used an array to initialize some of
the MDDRC parameters; however, the use of an array turned out to be a
bad idea as it was not possible to correlate structure entries to
array indices in readable and reliable way. Now we use a struct
instead, which makes this self-explanatory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The command "reginfo" got an overhaul for the ppc4xx. It dumps all the
relevant HW configuration registers (address, symbolic name, content).
This allows to easily detect errors in *.h files and changes in the HW
configuration.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify all existing *.c files to use the new register names
as seen in the AMCC manuals.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Unfortunately some Rev D PPC405EX/405EXr PVR's are identical with older
405EX(r) parts. Here a list:
0x12911475 - 405EX Rev D with Security *and* 405EX Rev A/B witout Sec
0x12911473 - 405EX Rev D without Security *and* 405EXr Rev A/B with Sec
Since there are only a few older parts in the field, this patch now
changes the PVR's above to represent the new Rev D versions.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Phong Vo" <pvo@amcc.com>
This message is printed upon PCIe bus scan, not only upon error, but also
if no PCIe device is detected at all. Since this is not an error, let's
remove this message in this case. We already have the message
"link is not up." if there is no PCIe device present.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
The SPD detection code for the Denali memory controller used on some
ppc4xx
processors incorrectly encodes DDR0_42. With certain memory
configurations,
this can cause the bootwrapper to incorrectly calculate the installed
memory
size, because the number of row bits is wrong. This patch fixes that
encoding.
Signed-off-by: Mike Nuss <mike@terascala.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch merges the ECC handling (ECC parity byte writing) into one
file (ecc.c) for all PPC4xx SDRAM controllers except for PPC440EPx/GRx.
This exception is because only those PPC's use the completely different
Denali SDRAM controller core.
Previously we had two routines to generate/write the ECC parity bytes.
With this patch we now only have one core function left.
Tested on Kilauea (no ECC) and Katmai (with and without ECC).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Felix Radensky <felix@embedded-sol.com>
Cc: Grant Erickson <gerickson@nuovations.com>
Cc: Pieter Voorthuijsen <pv@prodrive.nl>
Reorganize DDR2 ECC handling to use common code for
SPD DIMMs and soldered SDRAM. Also, use common code
to display SDRAM info (ECC, CAS latency) for SPD and
soldered SDRAM variants.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The latest PPC4xx register cleanup patch missed some SDRAM defines.
This patch now changes lower case UIC defines to upper case. Also
some names are changed to match the naming in the IBM/AMCC users
manuals (e.g. mem_mcopt1 -> SDRAM0_CFG).
Signed-off-by: Stefan Roese <sr@denx.de>
The latest PPC4xx register cleanup patch missed the UIC defines.
This patch now changes lower case UIC defines to upper case.
Signed-off-by: Stefan Roese <sr@denx.de>
some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurations might omit
setting e.g., DBYP since it was not documented in their SoC's RM.
Prevent them bricking their board by retaining power on reset values
in bit fields that the board porter doesn't explicitly configure
via CONFIG_SYS_<registername>_<bitfield> assignments in the board
config file.
also move LCRR assignment to cpu_init_r[am] to help ensure no
transactions are being executed via the local bus while CLKDIV is being
modified.
also start to use i/o accessors.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
U-Boot can detect if an IDE device is present or not.
If not, and this new config option is activated, U-Boot
removes the ATA node from the DTS before booting Linux,
so the Linux IDE driver does not probe the device and
crash. This is needed for buggy hardware (uc101) where
no pull down resistor is connected to the signal IDE5V_DD7.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Martha M Stan <mmarx@silicontkx.com>
Minor cleanup:
Re-ordered default_mddrc_config[] to have matching indices.
This allows to use the same index "N" for source and target fields;
before, we had code like this
out_be32(&im->mddrc.ddr_time_config2, mddrc_config[3]);
which always looked like a copy & paste error because 2 != 3.
Also, use NULL when meaning a null pointer.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The means to determine the core, bus, and DDR frequencies are completely
new on CoreNet style platforms. Additionally on p4080 we can have
different frequencies for FMAN and PME IP blocks. We need to keep track
of the FMAN & PME frequencies since they are used for time stamping
capabilities inside each block.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On CoreNet style platforms the timebase frequency is the bus frequency
defined by 16 (on PQ3 it is divide by 8). Also on the CoreNet platforms
the core not longer controls the enabling of the timebase. We now need
to enable the boot core's timebase via CCSR register writes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p4080 & p4040 to cpu_type_list and SVR list
* Added number of LAWs for p4080
* Set CONFIG_MAX_CPUS to 8 for p4080
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CoreNet platform style of bringing secondary cores out of reset is
a bit different that the PQ3 style. Mostly the registers that we use
to setup boot translation, enable time bases, and boot release the cores
have moved around.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On CoreNet based platforms the CCSRBAR address is split between an high &
low register and we no longer shift the address.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The code assumed names where just numbers and always prefixed 'mpc'.
However newer QorIQ don't follow the mpc naming scheme.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When boot from NAND, the NAND flash must be connected to br/or0.
Also init RAM(L2 SRAM or DDR SDRAM) for load the second image to
it.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The first stage 4K image uses a seperate ld script file to
generate 4K image. This patch moves it to the cpu/mpc85xx/*
to make it avaliable for 85xx platform.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
u-boot reports a PCIE PLL lock error at boot time on Yucca board, and
left PCIe nonfunctional. This is fixed by making u-boot function
ppc4xx_init_pcie() to wait 300 uS after negating reset before the
first check of the PLL lock.
Signed-off-by: Rupjyoti Sarmah <rsarmah@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
All 4xx variants had their own, mostly identical get_OPB_freq()
function. Some variants even only had the OPB frequency calculated
in this routine and not supplied the sys_info.freqOPB variable
correctly (e.g. 405EZ). This resulted in incorrect OPB values passed
via the FDT to Linux.
This patch now removes all those copies and only uses one function
for all 4xx variants (except for IOP480 which doesn't have an OPB).
Signed-off-by: Stefan Roese <sr@denx.de>
We should make sure to clear MSR[ME, CE, DE] when we boot an OS image
since we have changed the exception vectors and the OSes vectors might
not be setup we should avoid async interrupts at all costs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use write_tlb and don't use memset so we can use the same code for
cpu_init_early_f between NAND SPL and not.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536E is capable of booting form NAND/eSDHC/eSPI, this patch
implements these three bootup methods in a unified way - all of these
use the general cpu/mpc85xx/start.S, and load the main image to L2SRAM
which lets us use the SPD to initialize the SDRAM.
For all three bootup methods, the bootup process can be divided into two
stages: the first stage will initialize the corresponding controller,
configure the L2SRAM, then copy the second stage image to L2SRAM and
jump to it. The second stage image is just like the general U-Boot image
to configure all the hardware and boot up to U-Boot command line.
When boot from NAND, the eLBC controller will first load the first stage
image to internal 4K RAM buffer because it's also stored on the NAND
flash. The first stage image, also call 4K NAND loader, will initialize
the L2SRAM, load the second stage image to L2SRAM and jump to it. The 4K
NAND loader's code comes from the corresponding nand_spl directory, along
with the code twisted by CONFIG_NAND_SPL.
When boot from eSDHC/eSPI, there's no such a first stage image because
the CPU ROM code does the same work. It will initialize the L2SRAM
according to the config addr/word pairs on the fixed address and
initialize the eSDHC/eSPI controller, then load the second stage image
to L2SRAM and jump to it.
The macro CONFIG_SYS_RAMBOOT is used to control the code to produce the
second stage image for all different bootup methods. It's set in the
board config file when one of the bootup methods above is selected.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we move some of the functions in tlb.c around we need less
ifdefs. The first stage loader just needs invalidate_tlb and
init_tlbs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can pack the initial tlb_table in MAS register format and use
write_tlb to set things up. This savings can be helpful for NAND
style first stage boot loaders.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Factor out the code we use to actually write a tlb entry.
set_tlb is a logical view of the TLB while write_tlb is a low level
matching the MAS registers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Fix setting of ESDMODE (MR1) register - the bit shifting was wrong
* Fix the format string to match size in a debug print
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Skipping the interrupted instruction will accomplish nothing other
than turning a spurious interrupt into a crash.
External interrupts are not machine checks, so don't count them as such.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Its reset value is random, and we sometimes read uninitialized TLB
arrays. Make sure that we don't retain MAS8 from reading such an entry
if the VF bit in MAS8 is set, attempts to use the mapping will trap.
Signed-off-by: Scott Wood <scottwood@freescale.com>
We cannot handle any exceptions while running in AS1, as the exceptions
will transition back to AS0 without a valid mapping.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:
- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines
Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes the following compilation warning:
miiphy.c: In function 'emac4xx_miiphy_read':
miiphy.c:353: warning: dereferencing type-punned pointer will break
strict-aliasing rules
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the CONFIG_PCI_4xx_PTM_OVERWRITE option and replaces
the ugly 'if defined(BOARD1) || ... || defined(BOARDn)' construct
in 4xx pci code.
When CONFIG_PCI_4xx_PTM_OVERWRITE is defined the default ptm register
setup can be overwritten through environment variables ptm1la, ptm1ms,
ptm2la and ptm2ms to do application specific pci target BAR configuration.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Some board ports place TEXT_BASE at a location that would cause the
RESET_VECTOR_ADDRESS not to be at 0xfffffffc when we link. By default
we assume RESET_VECTOR_ADDRESS will be 0xfffffffc if the board doesn't
explicitly set it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
There is no reason to do a run time check for e500 v1 based cores to
determine if we have the GUTs RSTCR facility. Only the first generation
of PQ3 parts (MPC8540/41/55/60) do not have it. So checking to see if
we are e500 v2 would miss future parts (like e500mc).
Just change this to be ifdef'd based on CONFIG_MPC85{40,41,55,60}.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
While in probecpu() UART is still not initialized.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fixing the number of cores in the device tree based on the actual number of
cores on the system. With this same device tree image can be used for dual
core and single core members of otherwise exactly same SOC.
For example:
* P2020RDB and P2010RDB
* P1020RDB and P1011RDB
* MPC8641D and MPC8641
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Incase the system is detected with Unknown SVR, let the system boot
with a default value and a proper message.
Now with dynamic detection of SOC properties from SVR, this is necessary
to prevent a crash.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactor the code into a simple bitmask lookup table that determines if
a given PCI controller is enabled and if its in host/root-complex or
agent/end-point mode.
Each processor in the PQ3/MPC86xx family specified different encodings
for the cfg_host_agt[] and cfg_IO_ports[] boot strapping signals.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleaned up cpu/mpc85xx/Makefile to use CONFIG_* for those obvious cases
we have like PCI, CPM2, QE. Also reworked it to use one line per file
for everything and sorted in alphabetical order.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Its possible that we try and copy the boot page code out of flash into a
DDR location that doesn't have a TLB cover it. For example, if we have
3G of DDR we typically only map the first 2G. In the cases of 4G+ this
wasn't an issue since the reset page TLB mapping covered the last page
of memory which we wanted to copy to.
We now change the physical address of the reset page TLB to map to the
true physical location of the boot page code, copy and than set the
TLB back to its 1:1 mapping of the reset page.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allow us to search the TLB array based on an address. This is useful
if we want to change an entry but dont know where it happens to be
located.
For example, the boot page mapping we use on MP or the flash TLB that
we change the WIMGE settings for after we've relocated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In future Book-E implementations IVORs will most likely go away and be
replaced with fixed offsets. The IVPR will continue to exist to allow
for relocation of the interrupt vectors.
This code adds support to setup the IVORs as their fixed offset values
per the ISA 2.06 spec when we transition from u-boot to another OS
either via 'bootm' or a cpu release.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk
Niklaus Giger
Stefan Roese
Mike Nuss
Felix Radensky
Kim Phillips
Heiko Schocher
Martha M Stan
Kumar Gala
Vivek Mahajan
Mingkai Hu
Rupjyoti Sarmah
Scott Wood
Matthias Fuchs
Poonam Aggrwal