Your ROOT_URL in app.ini is https://src.whiteboxsystems.nl/ but you are visiting http://src.whiteboxsystems.nl/Whitebox/u-boot/commits/commit/9dec5270be87c01e50808001be69fce5b92a7af8/include
You should set ROOT_URL correctly, otherwise the web may not work correctly.
The bcm_ep board configuration is used by a number of boards
including Cygnus and NSP.
Add builds for the bcm958300k and the bcm958622hr boards.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
The Broadcom StarFighter2 Ethernet driver is used in multiple Broadcom
SoC(s) and:
- supports multiple MAC blocks,
- provides support for the Broadcom GMAC.
This driver requires MII and PHYLIB.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
To enable hypervisors utilizing the ARMv7 virtualization extension
on the Arndale board, add the simple SMP pen address writer function
and add the required configuration variables to switch all cores to
HYP mode before launching the OS.
This allows booting KVM and Xen directly from u-boot.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.
Signed-off-by: Pavel Machek <pavel@denx.de>
To fix the build error when build for Altera dev kit, not
virtual target. At same time, set the build for Altera dev
kit as default instead virtual target. With that, U-Boot
is booting well and SPL still lack of few drivers.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Commit e3a5bbce broke the FIT image tests by not loading a ramdisk even if
a load address is provided in the FIT. The rationale was that a load address
of 0 should be considered to mean 'do not load'.
Add a new load operation which supports this feature, so that the ramdisk
will be loaded if a non-zero load address is provided.
Signed-off-by: Simon Glass <sjg@chromium.org>
The commit (SHA1: 8fc171318e) reintroduced correct values for vendor and
product IDs required for UMS gadget to work properly either at Windows or
Linux.
This data was missing for GONI target, so this commit corrects this mistake.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
snyc with linux v3.15:
commit 1860e379875dfe7271c649058aeddffe5afd9d0d
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Jun 8 11:19:54 2014 -0700
Linux 3.15
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@ti.com>
while playing with the new mtd/ubi/ubifs sync, found some
small updates for it:
- add del_mtd_partition() to include/linux/mtd/mtd
- mtd: add a debug_printf
- remove some not used functions
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@ti.com>
resync ubi subsystem with linux:
commit 455c6fdbd219161bd09b1165f11699d6d73de11c
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Mar 30 20:40:15 2014 -0700
Linux 3.14
A nice side effect of this, is we introduce UBI Fastmap support
to U-Boot.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Joerg Krause <jkrause@posteo.de>
- move linux specific defines from usb and video code
into linux/compat.h
- move common linux specific defines from include/ubi_uboot.h
to linux/compat.h
- add for new mtd/ubi/ubifs sync new needed linux specific
defines to linux/compat.h
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[trini: Add spin_lock_irqsave/spin_unlock_irqrestore dummies from
usb/lin_gadet_compat.h]
Signed-off-by: Tom Rini <trini@ti.com>
from linux 3.14:
commit 455c6fdbd219161bd09b1165f11699d6d73de11c
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Mar 30 20:40:15 2014 -0700
Linux 3.14
Needed for the MTD/UBI/UBIFS resync
Just copied the files from Linux, and added in the c-file
the "#define __UBOOT__" for adding U-Boot special code. In
this case we use this just for adding including U-Boot
headers.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@ti.com>
resync with linux:
commit 455c6fdbd219161bd09b1165f11699d6d73de11c
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Mar 30 20:40:15 2014 -0700
Linux 3.14
Needed for the MTD/UBI/UBIFS resync
Just copied the files from Linux, changed the license file header,
and add in the c-file:
+#define __UBOOT__
#include <linux/rbtree_augmented.h>
+#ifndef __UBOOT__
#include <linux/export.h>
+#else
+#include <ubi_uboot.h>
+#endif
so, it compiles for U-Boot.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@ti.com>
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.
As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
SW5.1 (NAND_BOOTn) = OFF (logic-1)
SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)
And also set appropriate SYSBOOT configurations:
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */
Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.
am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a
time either eMMC or NAND can be enabled. Selection between eMMC and NAND is
controlled by:
(a) Statically using Jumper on connecter (J89) present on board.
(a) If Jumper on J89 is NOT used, then selection can be dynamically controlled
by driving SPI2_CS0[MUX_MODE=GPIO] pin via software:
SPI2_CS0 == 0: NAND (default)
SPI2_CS0 == 1: eMMC
am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI,
Thus only one of the two can be used at a time. Selection is controlled by:
(a) Dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)
NAND device (MT29F4G08AB) on these boards has:
- data-width=8bits
- blocksize=256KB
- pagesize=4KB
- oobsize=224 bytes
For above NAND device, ROM code expects the boot-loader to be flashed in BCH16
ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs.
Signed-off-by: Pekon Gupta <pekon@ti.com>
This patch
- consolidate CONFIG_SYS_NAND_xx and CONFIG_SPL_NAND_xx from various
configuration files into single file.
- update MTD Partition table to match AM335x_EVM DT in linux-kernel
- segregate CONFIGs based on different boot modes (like SPL and U-Boot)
Signed-off-by: Pekon Gupta <pekon@ti.com>
When we're using EMMC_BOOT that means we have environment on eMMC so
we can make use of CONFIG_SPL_ENV_SUPPORT within Falcon Mode.
Signed-off-by: Tom Rini <trini@ti.com>
In the case of SPL on these boards we only need environment for
SPL_USBETH, so it's safe to normally use ENV_IS_NOWHERE and SPL+NAND
does not support environment today.
Cc: Hannes Petermaier <oe5hpm@oevsv.at>
Signed-off-by: Tom Rini <trini@ti.com>
There are times where we may need more than a few kilobytes of stack
space. We also will not be using CONFIG_SPL_STACK location prior to DDR
being initialized (CONFIG_SYS_INIT_SP_ADDR is still used there) so pick
a good location within DDR for this to be. Tested on
OMAP4/AM335x/OMAP5/DRA7xx.
Signed-off-by: Tom Rini <trini@ti.com>
On am335x_evm we only support USBETH for a networking SPL option so move
the rest of the defines under that area as that's the only time we need
(and want) environment support here.
Signed-off-by: Tom Rini <trini@ti.com>
The Altera EPCS is SPI flash. We have been using SPI flash driver
to access EPCS for years. The old EPCS driver could be removed.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
This patch implements the generic board init as described in
doc/README.generic-board.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit b3dd64f5d5 "bootm: use genimg_get_kernel_addr()" introduced
a bug for booting FIT image. It's because calling fit_parse_config()
twice will give us wrong value in img_addr.
Add a new function genimg_get_kernel_addr_fit() whichl will always
return fit_uname_config and fit_uname_kernel for CONFIG_FIT.
genimg_get_kernel_addr() will ignore those to parameters.
Reported-by: York Sun <yorksun@freescale.com>
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Add a BSD-3 relicensed version of the Android sparse format image
header from:
28fa5bc347/libsparse/sparse_format.h
Unchanged except for the license header.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Colin Cross <ccross@android.com>
Emails to the board maintainer
"Rishi Bhattacharya <rishi@ti.com>"
have been bouncing.
Tom suggested to remove this board.
Remove also omap1510_udc.c because this is the last board
to enable it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
The following configs are not defined at all:
- CONFIG_INCA_IP_SWITCH
- CONFIG_PBL2800_ETHER
- CONFIG_PHY_ICPLUS
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
When u-boot initializes the RAM (early in boot) it looks for the "pram"
env variable to know which is area it cannot use. If the "pram" env variable
is not found, the default CONFIG_PRAM value is used.
This value used to be 0 (no protection at all). This patch sets it to a
value that covers PHRAM and PNVRAM that must be protected in our case.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.
Add support for one FEC port initially.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
It is necessary to provide the same Vendor and Product IDs as the one in
the original Linux kernel code.
Without this change the USB mass storage gadget is not working with Windows7.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
The Gateworks Ventana EEPROM contains a set of configuration bits that
affect the removal of device-tree nodes that support peripherals that do not
exist on sub-loaded boards. This patch adds:
- a structure to define a config bit name, dt node alias, bit position
- an array of supported configuration items
- an econfig command to get/set/list configuration bits
- use of the array when adjusting the FDT prior to boot
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Building the SPL in Thumb mode saves roughly 30% in size of the
resulting SPL binary. As the size of SPL it limited on the MX6,
this helps a lot.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
This allows u-boot to load different OS or Bare Metal application on
different cores of the i.MX6 SoC.
For example: running Android on cpu0 and a RT OS like QNX/FreeRTOS on cpu1.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Stefano Babic <sbabic@denx.de>
This adds board support for the Toradex Colibri T30 module.
Working functions:
- SD card boot
- eMMC environment and boot
- USB host/USB client (on the dual role port)
- Network (via ASIX USB)
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable DFU protocol support (via the "dfu" command) on Tegra boards where
USB device/gadget mode is enabled.
Note that for DFU to operate correctly on Tegra, we still need some DFU
fixes/enhancements that are going through the DFU -> USB trees. However,
the code builds just fine without those changes, and applying this patch
now will allow both sets of patches to meet in the main U-Boot tree much
more quickly.
In order to run test/dfu/dfu_gadget_test.sh, you would need to add the
following to the board configuration:
CONFIG_EXT4_WRITE
CONFIG_CMD_EXT4_WRITE
However, I haven't enabled those here, since I believe the main use-case
for DFU on Tegra is raw flash writing, rather than filesystem access, so
we don't need the additional code-size hit. However, I could be persuaded
otherwise! We should probably add a separate test script for raw flash
access.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Set CONFIG_BOARD_SIZE_LIMIT so we'll notice at build time if U-Boot
has grown so large that it would overlap with the environment area in
flash, rather than bricking the device at run-time on first saveenv.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Add deep sleep support in SPI/SD boot. The destination address
second stage uboot image is loaded to is changed because
currently this address will be used by kernel which means
we can't reserve it for resume.
Entry point to kernel is still placed in second stage uboot.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Scott Branden
Jiandong Zheng
Andre Przywara
Pavel Machek
Chin Liang See
Simon Glass
Łukasz Majewski
Heiko Schocher
Matwey V. Kornilov
Lokesh Vutla
Dmitry Lifshitz
Jeroen Hofstee
pekon gupta
Tom Rini
Thomas Chou
Bryan Wu
Colin Cross
Marek Vasut
Hans de Goede
Masahiro Yamada
Valentin Longchamp
Fabio Estevam
Tim Harvey
Gabriel Huau
Stefan Agner
Stephen Warren
Sascha Silbe
Tang Yuantian