The last 64 byte of each DDR channel of PH1-LD20 is periodically
used as a scratch area for the DDR PHY training.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The current table look-up for the DTB file name turned out bothersome
in terms of maintainability; I ended up adding a new entry every time
a new board is supported.
There is a common pattern between the DT compatible string and the
corresponding file name; drop the vendor prefix "socionext," and
prefix it with "uniphier-" and suffix it with ".dtb".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
No need to stop booting U-Boot even if boot mode is unknown.
Setting the "bootmode" environment is only useful for booting
Linux Kernel. Anyway, U-Boot has already booted by this point.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For PH1-LD20 or later, per-pin input-enable control is supported,
that is, we need to set-up IECTRL registers for a group of pins.
This helper function will be useful for a bunch of register settings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtgrep would not accept uniphier-ph1-ld20-ref.dtb
and uniphier-ph1-ld11-ref.dtb unless the aliases node comes
the first in the root node.
$ make -s uniphier_pxs2_ld6b_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-ld20-ref
[snip]
LDS spl/u-boot-spl.lds
LD spl/u-boot-spl
OBJCOPY spl/u-boot-spl-nodtb.bin
FDTGREP spl/u-boot-spl.dtb
Error at 'fdt_find_regions': FDT_ERR_BADLAYOUT
/aliases node must come before all other nodes
Error: FDT_ERR_BADMAGIC
make[1]: *** [spl/u-boot-spl.dtb] Error 1
make: *** [spl/u-boot-spl] Error 2
This commit moves the aliases node as the error message from the
fdtgrep tool suggests, although this requirement does not sound
reasonable to me.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Because DT properties are 4-byte aligned, the pointer access
*(fdt64_t *) in this code causes unaligned access.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I found many mistakes in the initial version.
Fixes: 8a3328c209 ("pinctrl: uniphier: support UniPhier PH1-LD20 pinctrl driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In list "super_blocks" ubifs collects allocated super_block
structs. U-Boot frees on unmount the allocated struct,
so the pointer stored in this list is free after the umount.
On a new ubifs mount, the new allocated super_block struct
get inserted into the super_blocks list ... which contains
now a freed pointer, and the list_add_tail() corrupts the
freed memory ...
2 solutions are possible:
- remove the super_block from the super_blocks list
on umount
- as U-Boot does not use the super_blocks list ...
remove it complete for U-Boot.
Both solutions should not introduce problems for porting
to newer linux version, so this patch removes the unused
super_blocks list, as it saves code size and execution
time.
Signed-off-by: Heiko Schocher <hs@denx.de>
Set free_count to zero before walking through ai->erase list
in wl_init().
As U-Boot has no workqueue/threads, it immediately calls
erase_worker(), which increase for each erased block
free_count. Without this patch, free_count gets after
this initialized to zero in wl_init(), so the free_count
variable always has the maybe wrong value 0.
Detected this behaviour on the dxr2 board, where the
UBI fastmap gets not written when attaching/dettaching
on an empty NAND. It drops instead the error message:
could not find any anchor PEB
With this patch, fastmap gets written on dettach.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Our own ACPI implementation (when CONFIG_QEMU_ACPI_TABLE is not set)
does not build anymore after x86 has been fully converted to DM PCI.
Instead of trying to fix the build errors, given we now have the ACPI
support via QEMU's fw_cfg interface, which is a more reliable way to
generate correct ACPI tables than by ourselves, hence drop our own
ACPI implementation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
flush_dcache_all() is used in the very end of U-Boot self relocation
to write back all copied and then patched code and data to their
new location in the very end of available memory space.
Since that has nothing to do with IO (i.e. no external DMA happens
here) IOC won't help here and we need to write back data cache contents
manually.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Previously, ret could be used uninitialized if
blk_get_device_part_str() failed. Default to ret being set to -1 so
that we always return an err up if we have a problem and then invert the
logic on testing ums_count as when that is non-zero is the time we can
return 0.
Cc: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
While at it, remove obsolete CONFIG_USBDOWNLOAD_GADGET option from some
config headers. This is also probably fixes am335x_baltos board.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and
make all UDC controllers select USB_GADGET_DUALSPEED:
- add next options to Kconfig selecting USB_GADGET_DUALSPEED:
- USB_GADGET_ATMEL_USBA
- USB_GADGET_DWC2_OTG
- USB_DWC3
- CI_UDC
- make USB_MUSB_GADGET select USB_GADGET_DUALSPEED
While at it, make some related fixes:
- remove DUALSPEED from configs that don't enable gadget support:
- kwb.h
- tseries.h
- add missing USB_GADGET option to next configs:
- novena_defconfig
- pcm051_rev*_defconfig
- xfi3_defconfig
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
The description was borrowed from kernel. Definitions were added to
defconfig files in a way that "make savedefconfig" generates exactly
the same file as used defconfig.
Boards using 0 mA as CONFIG_USB_GADGET_VBUS_DRAW value were moved to use
2 mA (as minimal allowed by Kconfig).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
By applying this patch, it will give us some flexibility to expose
a selected partition/s.
e.g:
1. To expose several partitions
ums 0 mmc 0:1,0:6
2. To expose the all partitions
ums 0 mmc 0:0
3. To expose multiple partititions on several devices
ums 0 mmc 0:1,1:6
4. It support legacy format
ums 0 mmc 0
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
The USB Mass Storage (ums) works in Windows, Linux and OS X (EL Capitan).
But, not in OS X (Yosemite). By applying the said patch, it extends
the ums support.
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid XU3 (./test/py UMS + DFU tests)
Tested-by: John Tobias <john.tobias.ph@gmail.com>
Linux:
- Run ums to expose all my eMMC partition - shows all correctly
- Run ums to expose only 1 partition of my eMMC - show correctly
Windows:
- Run ums to expose all my eMMC partition - it detects but it prompts,
if I want to format it (due to a non windows partition)
- Run ums to expose only the FAT32 partition - it show the partition
correctly.
This enables full ethernet usage, including U-Boot to write the board
specific MAC address (ethaddr) into the DT blob before passing it to
Linux.
Without this, the ethaddr is not detected in U-Boot at all, resulting
in this error upon bootup:
...
Model: EBV SOCrates
Net:
Error: ethernet@ff702000 address not set.
No ethernet found.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Fix a small typo in some of the SoCFPGA dts files that has spread via
copy-and-paste.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
The code uses a lot of signed numbers, which ended up in variables
of unsigned type, which resulted in all sorts of underflows. This
in turn caused incorrect calibration on certain boards. Moreover,
repair the readout of the DQ delay, which was being pulled from
wrong register.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Just staticize global variables in sequencer, since there is no
point in having these symbols available outside of the DDR code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Originally, the DLEVEL selects the debug level within the sequencer code,
but only displays the messages on that particular debug level. Tweak the
handling such that for particular debug level, debug messages on that
level and lower are displayed. This allows better regulation of debug
message verbosity.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
This one last set of delay configuration registers was not properly
zeroed out originally, fix it and zero them out.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
There is no point in resetting the ODT setting if the write test
failed, since the code will always retry the calibration and thus
reconfigure the ODT anyway OR the code will fail calibration and
halt.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Every invocation of the scc_mgr_set_dqs_en_delay_all_ranks() is
followed by SCC manager update. Moreover, only this function
triggers the SCC manager update internally. Thus, remove the
internal invocation to avoid triggering the update twice.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
The hi address bitfield in the protection rule must be set to
the last address in the region which the rule represents. The
behavior is now in-line with code generated by Quartus 15.1 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
The code should be setting registers to zero, not one register to value.
Swap the order of arguments to correct the behavior. The behavior is now
in-line with code generated by Quartus 15.1 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
In the most unlikely case the DQS tracking was to be disabled,
make sure we do not errornously re-enable it. Note that DQS
tracking is enabled on all systems observed thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
The bit 22 is in fact DQS tracking enable bit (dqstrken) and there
is a macro for this bit already, so use it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Add support for Technexion's PICO-IMX6UL-EMMC board.
For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
On a reset/reboot, the display power needs to be off for atleast 500ms
before turning it back on. So add a delay to the boot process to meet
the display timing requirement.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
To generate accurate pixel clocks required by the displays we need to
set the ldb_di_clk source on bx50v3 to PLL3 and b850v3 to PLL5. Since
PLL5 is disabled on reset, we need to enable PLL5.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
B450v3/B650v3 uses single channel LVDS and does not support HDMI.
B850v3 uses dual channel LVDS and supports HDMI. Hence split the display
setup into two different functions.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk tree,
the glitchy parent mux of ldb_di[x]_clk can cause a glitch to enter the
ldb_di_ipu_div divider. If the divider gets locked up, no ldb_di[x]_clk is
generated, and the LVDS display will hang when the ipu_di_clk is sourced from
ldb_di_clk.
To fix the problem, both the new and current parent of the ldb_di_clk should
be disabled before the switch. This patch ensures that correct steps are
followed when ldb_di_clk parent is switched in the beginning of boot.
This patch was ported from the 3.10.17 NXP kernel
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/?h=imx_3.10.17_1.0.1_ga&id=eecbe9a52587cf9eec30132fb9b8a6761f3a1e6d
NXP errata number: ERR009219, EB821
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
The echo -ne "\xNN" does not work in certain bourne-compatible shells, like
dash. The recommended way of hex->char conversion is using printf(1), but
there is a pitfall here. The GNU printf does support "\xNN" format, but
according to the opengroup documentation, this is not part of POSIX. The
POSIX printf only defines "\NNN" where N is octal. Thus, for the sake of
compatibility, we use that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Masahiro Yamada
Tom Rini
Heiko Schocher
Bin Meng
Alexey Brodkin
Sam Protsenko
John Tobias
Stefan Roese
Marek Vasut
Fabio Estevam
Akshay Bhat