Currently, regmap_init_mem() takes a udevice. This requires the node
has already been associated with a device. It prevents syscon/regmap
from behaving like those in Linux.
Change the first argumenet to take a device node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
RK3188 using the same ddr_conf for both 15 bit and 16 bit row address.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed compile-error by declaring 'row':]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Replace the sdram_init() in board init and rockchip_sdram_size() in
sdram driver for all the Rockchip SoCs which enable CONFIG_RAM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make dram_init() in rk3036-board.c conditional on CONFIG_RAM:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the DRAM controller initialisation for the RK3188, RK3288
and RK3399... all of these read some of the tuning/setup/timing
parameters from the device-tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Right now we're setting the wrong value of 0 as base in the ram_info struct,
which is obviously wrong for the rk3188. So instead set the correct value
we already have in CONFIG_SYS_SDRAM_BASE.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The sdram controller blocks are very similar to the rk3288 in utilizing
memory scheduler, Designware uPCTL and Designware PUBL blocks, only
limited to one bank instead of two.
There are some minimal differences when setting up the ram, so it gets
a separate driver for the rk3188 but reuses the driver structs, as there
is no need to define the same again.
More optimization can happen when the modelling of the controller parts
in the dts actually follow the hardware layout hopefully at some point
in the future.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
The sdram IP blocks used on rk3066, rk3188 and rk3288 are very similar
and we want to unify things once all 3 work as expected.
Therefore try to keep the rk3288 sdram driver in line by applying the
general review comments received for the rk3188 variant to it as well.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Use defines to describe the bit shifts used to create the
table for ddrconf register values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for rk3288 dram capacity auto detect, support DDR3 and
LPDDR3, DDR2 is not supported.
The program will automatically detect:
- channel number
- rank number
- column address number
- row address number
The dts file do not need to describe those info after apply this patch.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
The all current Rockchip SoCs supporting 4GB of ram have problems
accessing the memory region 0xfe000000~0xff000000. Actually, some IP
controller can't address to, so let's limit the available range.
This patch fixes a bug which found in miniarm-rk3288-4GB board. The
U-Boot was relocated to 0xfef72000, and .bss variants was also
relocated, such as do_fat_read_at_block. Once eMMC controller transfer
data to do_fat_read_at_block via DMA, DMAC can't access more than
0xfe000000. So that DMAC didn't work sane.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The ChromeOS kernel reads the RAM settings from PMU_SYS_REG2 and expects
the bootloader to store the necessary information there. We're using
the same register to pass the same information between the SPL and
U-Boot but in a slightly different format.
Change this to use the format expected by the Linux DMC driver so that
the system doesn't hang in Linux by misconfiguring the RAM.
This is almost the same as commit b5788dc ("rockchip: rk3288: correct
sdram setting") which was reverted in commit b525556 ("Revert "rockchip:
rk3288: correct sdram setting"") but parenthese have been added to apply
the mask correctly when reading the "bw" setting and a couple of minor
style issues have been fixed to keep check_patch.pl happy.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
The current code picks the first available clock. In U-Boot proper this is
the oscillator device, not the SoC clock device. As a result the HDMI display
does not work.
Fix this by calling rockchip_get_clk() instead.
Fixes: 135aa950 (clk: convert API to match reset/mailbox style)
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
The function is very specific to the rk3288 in its arguments
referencing the rk3288 cru and grf and every other rockchip soc
has differing cru and grf registers. So make that function naming
explicit.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Add support for of-platdata with rk3288 SDRAM initr. This requires decoding
the of-platdata struct and setting up the device from that. Also the driver
needs to be renamed to match the string that of-platdata will search for.
The platform data is copied from the of-platdata structure to the one used
by the driver. This allows the same code to be used with device tree and
of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is more correct to avoid touching the device tree in the probe() method.
Update the driver to work this way. Note that only SPL needs to fiddle with
the SDRAM registers, so decoding the platform data fully is not necessary in
U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This reverts commit b5788dc0dd.
Ram size is incorrectly reported as 512MB on a firefly-rk3288 board
with 2GB of ram. Reverting this patch displays the full amount of ram.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Simon Glass <sjg@chromium.org>
The DMC driver in v3.14 kernel[0] get the ddr setting from PMU_SYS_REG2,
and it expects uboot to store the value using a same protocol. But now
the ddr setting value is different with DMC, so if you enable the DMC,
system would crash in kernel. Correct the sdram setting here, according
to the requirements of kernel.
[0]
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/
chromeos-3.14/drivers/clk/rockchip/clk-rk3288-dmc.c
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a feature which speeds up the CPU to full speed in SPL to minimise
boot time. This is only supported for certain boards (at present only
jerry).
Signed-off-by: Simon Glass <sjg@chromium.org>
Add code to set up the SDRAM in SPL, ready for loading U-Boot. This uses
device tree for configuration so should be able to support other RAM
configurations. It may be possible to generalise the code to support other
SoCs at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada
Tom Rini
Kever Yang
Philipp Tomsich
Simon Glass
Heiko Stübner
Xu Ziyuan
John Keeping
Stephen Warren
Vagrant Cascadian
Chris Zhong