Rename all references to kirkwood in mvgbe symbols
throughout the whole codebase.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* the following problems are met :
config was set to use the new driver as a default but
- RMII was not enabled for the new driver
- the new driver didn't compile with RMII enabled
- the new driver initialize a PHY at address O when the PHY of
this board is at 1 thus we get "AT91 EMAC RMII: No PHY present"
* to fix these problems, this patch :
- enable RMII for the new driver
- fix the wrong define used in the at91_emac.c
- allow the config file to set a default phy address (and use
0 as a default as in the actual at91_emac.c driver)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Remove some INFERNO related #ifdef's from common environment code by
fixing the board configuration settings (add CONFIG_ENV_SECT_SIZE).
While we are at it, fix comment which incorrectly talks about 4 KB
environment size, while it's actually 0x4000 = 16 KiB.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Rolf Offermanns <rof@sysgo.de>
On P2020RDB eTSEC2 is connected to Vitesse VSC8221 PHY via SGMII.
Current TBI PHY settings for SGMII mode cause link problems on
this platform, link never comes up.
Fix this by making TBI PHY settings configurable and add a working
configuration for P2020RDB.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
On P2020RDB eTSEC2 is connected to Vitesse VSC8221 PHY via SGMII.
Current TBI PHY settings for SGMII mode cause link problems on
this platform, link never comes up.
Fix this by making TBI PHY settings configurable and add a working
configuration for P2020RDB.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Because the variable was getting defined twice.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The AmigaOneG3SE board has been orphaned or a very long time, and
broken for more than 12 releases resp. more than 3 years. As nobody
seems to be interested any more in this stuff we may as well ged rid
of it, especially as it clutters many areas of the code so it is a
continuous pain for all kinds of ongoing work.
Signed-off-by: Wolfgang Denk <wd@denx.de>
CONFIG_SYS_BUS_HZ has not really been used anywhere except to be
redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the
bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the
funtionality. Change all this to use CONFIG_SYS_BUS_CLK consistently.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Eran Man <eran@nbase.co.il>
Cc: Stefan Roese <sr@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Currently EMAC_MDIO_PHY_NUM is defined as 1 in emac_defs.h.
Because of this, EMAC does not work on EVMs which do not have phy
connected at 1. Moving the macro to board config file makes this
configurable depending on where the phy is connected on the MDIO bus.
This patch fixes the board reset issue observed during network access
on DM365EVM. EMAC driver was assuming EMAC_MDIO_PHY_NUM as 1
but it is 0 on DM365EVM.
This patch is verified on da830/omap-l137, dm365 and dm644x evms.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the LaCie ED Mini V2 product
which is based on the Marvell Orion5x SoC.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
This patch adds support for the Samsung Goni board (S5PC110 SoC)
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Provides initial support for TI OMAP-L138/DA850 SoC devices on
a Logic PD EVM board.
Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the EMIF4 interface
available in the AM35x processors.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The EVMS have been shipping with NAND (instead of OneNAND) as default.
So, this patch sets NAND as default.
To choose OneNAND, define CMD_ONENAND instead of CMD_NAND in the
config file omap3_evm.h.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals. This patch adds support for the
TNETV107X EVM board.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture. The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.
Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.
1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.
2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM. Added support for this capability in ARM1176 architecture.
3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.
4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include. The presence
of this include prevents builds on other ARM1176 archs.
5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the EMIF4 interface
available in the AM35x processors.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The EVMS have been shipping with NAND (instead of OneNAND) as default.
So, this patch sets NAND as default.
To choose OneNAND, define CMD_ONENAND instead of CMD_NAND in the
config file omap3_evm.h.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals. This patch adds support for the
TNETV107X EVM board.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture. The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.
Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.
1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.
2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM. Added support for this capability in ARM1176 architecture.
3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.
4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include. The presence
of this include prevents builds on other ARM1176 archs.
5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add the new board PM9G45 from Ronetix GmbH.
* AT91SAM9G45 MCU at 400Mhz.
* 128MB DDR2 SDRAM
* 256MB NAND
* 10/100 MBits Ethernet DP83848
* Serial number chip DS2401
The board is made as SODIMM200 module.
For more info www.ronatix.at or info@ronetix.at.
Signed-off-by: Asen Dimov <dimov@ronetix.at>
This patch changed the SICRL_USBDR define to reflect the 4 different bit
settings for this two-bit field. The four different options are '00', '01',
'10', and '11'. This patch also corrects the config file for SIMPC8313 and
MPC8313ERDB for the appropriate fields. This change only affects the MPC8313
cpu.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds gpio support of Altera PIO component to the
nios2-generic board. Though it drives only gpio_led at the
moment, it supports bidirectional port to control bit-banging
I2C, NAND flash busy status or button switches, etc.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
This patch sets the SICRL_LBC bits in SICRL to change the function of the
associated pins to GPIO functionality.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Add USB commands.
Rename autoscript to bootscript.
Add automatic bootscript image generation to makefile.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Added UPM array table, upmconfig, and Local Bus configuration support for SIMPC8313
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add ECC support for DDR RAM for MV64360 on esd CPCI-CPU/750 board.
This patch also adds the "pldver" command to display the CPLD
revision.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
The RTC is part of the Freescale's PMIC controller.
Use general function to access to PMIC internal registers.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
The NAND device is connected to the FPGA of the QONG board
and not to the NFC controller. For this reason, the FPGA must
be set and initialized before accessing to the NAND itself.
Signed-off-by: Stefano Babic <sbabic@denx.de>
moved CONFIG_CMD_FAT to filesystem section
swapped CONFIG_CMD_NAND and CONFIG_CMD_MII so they are alpha correct
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Albert Aribaud
Eric Bénard
Wolfgang Denk
Stefan Roese
Felix Radensky
Poonam Aggrwal
Prakash PM
Anatolij Gustschin
Albert Aribaud
Minkyu Kang
Sudhakar Rajashekhara
Vaibhav Hiremath
Cyril Chemparathy
Asen Dimov
Ron Madrid
Thomas Chou
Stefano Babic
Andre Schwarz
Reinhard Arlt
Graeme Russ
Magnus Lilja
Kim Phillips
Frans Meulenbroeks