remove the seldomly used EXT2 support because the U-Boot binary will
not fit into the 512KiB flash otherwise.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
fix broken SPI access by adding/activating BOARD_EARLY_INIT_F
functionality and calling spi_init_f() from there.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
A number of network related files were imported from the LiMon
project; these contain a somewhat unclear license statement:
Copyright 1994 - 2000 Neil Russell.
(See License)
I analyzed the source code of LiMon v1.4.2 which was used for this
import. It does not contain any "License" file, but the top level
directory contains a file "COPYING", which turns out to be GPL v2
of June 1991. So it is legitimate to conclude that the LiMon derived
files are also to be released under GPLv2. Mark them as such.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix typo of commit d4e53f063d.
i2c2 pullup resisters are controlled by bit 0 of CONTROL_PROG_IO1.
It's value after reset is 0x00100001.
In order to clear bit 0, original code write 0xfffffffe to
CONTROL_PROG_IO1 and toggle almost all default values.
Original code affect following:
* disable i2c1 pullup resisters
* increase far end load setting for many modules
* setup invalid SC/LB combination
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Steve Kipisz <s-kipisz2@ti.com>
This board has been orphaned for more than 6 months.
It is the last board defining CONFIG_APM821XX.
The code inside #ifdef CONFIG_APM821XX should be removed too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In some cases, the last lines of SPL or TPL are not output to a file.
The entries remaining in the "unmatched" variable must be flushed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
At least on OMAP, init_sata() no longer performs scsi_scan()
so we must do it explicitly here.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().
Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.
Signed-off-by: Roger Quadros <rogerq@ti.com>
The DMA/FIS buffers are set in ahci_port_start() which is called
after ahci_host_init(). So don't start the DMA engine here
(i.e. don't set FIS_RX)
This fixes the following error at kernel boot on OMAP platforms (e.g. DRA7x)
WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x260/0x358()
44000000.ocp:L3 Custom Error: MASTER SATA TARGET GPMC (Idle): Data Access in User mode during Functional access
Signed-off-by: Roger Quadros <rogerq@ti.com>
Commit 12cc543767 'omap3: overo: Select
fdtfile for expansion board' wrongly missed the operator in the fdtfile
test. Update the test to only overwrite an empty fdtfile environment
variable.
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Commit 294b91a581 moved initr_malloc
earlier than initr_unlock_ram_in_cache. This causes issue on T4240.
It may be related to locked L1 d-cache and unlocked L2 cache. D-
cache could and should be unlock earlier for normal operation.
This patch moves initr_unlock_ram_in_cache before initr_malloc. It
has been verified on the following boards, in which only T4240QDS
suffered and has been since fixed: T4240QDS, T2080QDS, P5040DS,
P4080DS, MPC8572DS, MPC8536DS, MPC8641HPCN, B4860QDS.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
On a couple of platforms I've tripped over long PXE append lines overflowing
this array, due to having CONFIG_SYS_CBSIZE == 256. When doing preseeded Debian
installs it's pretty trivial to exceed that.
Since the symptom can be a silent hang or a crash add a check. Of course the
affected boards would also need an increased CBSIZE to actually work.
Note that due to the printing of the final bootargs string CONFIG_SYS_PBSIZE
also needs to be sufficiently large.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
[trini: Use %zd not %d in printf for all args]
Signed-off-by: Tom Rini <trini@ti.com>
The function nand_flash_detect_ext_param_page() requires
NAND_CMD_RNDOUT command supported. It is necessary to detect some
types of ONFi-compliant devices. Without it, the error message
"unsupported command received 0x5" is shown.
Let's support this command on the Denali NAND controller driver.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
NAND_CMD_PARAM (0xEC) command is not working on the Denali
NAND controller driver.
Unlike NAND_CMD_READID (0x90), when the NAND_CMD_PARAM command
is followed by an address cycle, the target device goes busy.
(R/B# is deasserted)
Wait until the parameter data are ready.
In addition, unnecessary clear_interrupts() should be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
Add default eeprom bus setting.
This addresses the trimslice compile error that was introduced
with the addition of this setting.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
rmobile/lowlevel_init_ca15.S are common in r8a7790, r8a7791 and r8a7794 of
rmobile SoCs. The initialize L2 cache in lowlevel_init_ca15.S only needed
for Cortex-A15. The r8a7794 is Cortex-A7, not Cortex-A15.
This adds Skip to initialize L2 cache when r8a7794.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
rmobile/lowlevel_init_ca15.S are common in r8a7790 and r8a7791 of
rmobile SoC. But L2 cache of r8a7791 does not use L2CTLR[5].
This adds fix to set L2CTLR [5] only when the r8a7790.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
SCIF of koelsch use external clock mode.
This enables external clock mode on koelsch board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
SCIF of lager use external clock mode.
This enables external clock mode on lager board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The clock of SCIF (serial port) of lager is supplied from External
Clock. And value of clock is 14.7456MHz.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
In order for the gmac nic to work reliable on the Bananapi, we need to set
bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain" of the GMAC clk register
(0x01c20164) to 3.
Without this about 9 out of 10 ethernet packets get lost, with this setting
there is no packet loss.
So far setting these bits is only necessary on the Bananapi, so this commit
solves this with a bit of #ifdef CONFIG_BANANAPI code. If in the future we
need to do something similar for other boards, we can create a specific
CONFIG_FOO option for this then.
Reported-by: Karsten Merker <merker@debian.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Zoltan HERPAI <wigyori@openwrt.org>
Tested-by: Tony Zhang <tony.zhang@lemaker.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This change fixes suspend/resume issue in the kernel caused
by the wrong 'aclk_cores' clock value expected by the kernel.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The email address of Rajeshwari Shinde <rajeshwari.s@samsung.com>
is not working.
This commit gives Akshay the maintainership of Snow and
SMDK5420 boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move cache handling code to C file, and add enable_caches() and
disable_caches() functions.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enable this feature to support driver model before relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Change this board to add a device tree.
This also adds a pinmux header file although it is not used as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Most of the smdkv310 features are common with other exynos4 boards. To
permit easier addition of driver model support, use the common file and
add a device tree file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Most of the arndale features are common with other exynos5250 boards. To
permit easier addition of driver model support, use the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These boards do not in fact have a Chrome OS EC, nor a TPS565090 PMIC, so
move the settings into a separate common file to be used by those that need
it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
A few things are common but are not in the common file. Fix this and
rename the file to fit with the other exynos*-common files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since exynos4 and exyno5 share many settings, we should move these into
a common file to avoid duplication.
In effect the changes are that all exynos boards now have EXT4 and FAT
write support. This affects exynos5250 and exynos5420 which previously
did not. This also disables the ext2 commands which are equivalent to
ext4 anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
David Müller (ELSOFT AG)
Wolfgang Denk
Alexander Kochetkov
Masahiro Yamada
Khoronzhuk, Ivan
Roger Quadros
Stefan Herbrechtsmeier
York Sun
Ian Campbell
Albert ARIBAUD
Nikita Kiryanov
Nobuhiro Iwamatsu
Hans de Goede
Przemyslaw Marczak
Robert Baldyga
Simon Glass