Since we use CONFIG_SYS_GENERIC_BOARD on x86, we don't need this anymore.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
Since we don't have real-mode code now, we can remove this chunk of the link
script.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ pointed out that this code is no longer used. Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
The define should not have been put in fdt.h originally, libfdt_env.h
is the proper place for target-specific customizations.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This commit adds a license header to fdt.h and libfdt_env.h
because the license was omitted.
U-Boot note: the u-boot libfdt_env.h header portion was not applied to
the u-boot libfdt_env.h because that file was created by Gerald Van Baren
(with a license header). - gvb
Ref: DTC commit 27cdc1b1
Signed-off-by: Justin Sobota <jsobota@ti.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This function is useful outside libfdt, so export it.
Ref: DTC commit b7aa300e
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Since there are two memory areas defined, vectors and ram,
the linker will error when neither of them are specified for a
section.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
The 512 byte block size was hard coded in the ext4 file systems.
Large harddisks today support bigger block sizes typically 4096
bytes.
This patch removes this limitation.
Signed-off-by: Egbert Eich <eich@suse.com>
Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them. Also fix reference to doc/README.SPL file.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Patman requires python 2.7.4 to run but it doesn't
need to be placed in /usr/bin/python.
Use env to ensure that the interpreter used is
the first one on environment's $PATH on system
with several versions of Python installed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Conflicting tags can prevent buildman from building two series which exist
one after the other in a branch. There is no reason not to allow this sort
of workflow with buildman, so ignore conflicting tags in buildman.
Change-Id: I2231d04d8684fe0f8fe77f8ea107e5899a3da5e8
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
If the environment contains an entry like "=value" "\0" we should throw
an error when parsing the environment. Otherwise, U-Boot will enter in
an infinite loop.
Signed-off-by: Lucian Cojocar <cojocar@gmail.com>
Currently the base setting for CFLAGS is split in two possibilities,
one with -DBUILD_TAG appended at the end and one without, the rest of
CFLAGS is the same in both cases. Change this so CFLAGS are always set
and the -DBUILD_TAG is appended in separate ifdef.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Microblaze uses gpio which is connected to the system reset.
Currently gpio subsystem wasn't used for it.
Add gpio driver and change Microblaze reset logic to be done
via gpio subsystem.
There are various configurations which Microblaze can have
that's why gpio_alloc/gpio_alloc_dual(for dual channel)
function has been introduced and gpio can be allocated
dynamically.
Adding several gpios IP is also possible and supported.
For listing gpio configuration please use "gpio status" command
This patch also remove one compilation warning:
microblaze-generic.c: In function 'do_reset':
microblaze-generic.c:38:47: warning: operation on '*1073741824u'
may be undefined [-Wsequence-point]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
fdt_initrd add additional information to DTB about initrd
addresses which are later used by kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Include this header to get access to link symbols, which are otherwise
removed.
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
A malloc() followed by memset() can be simply replaced by calloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If failed the add_host(), it is reasonable that return value of
add_sdhci().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Without this additional delay, some eMMC don't negotiate properly bus width
Tested on:
- Toshiba THGBM2G8D8FBAIB
- Toshiba THGBM4G4D1HBAR
- Micron MTFC4GMVEA (the one giving the problem)
- Hynix H26M64002BNR
- SanDisk SDIN5E1-32G
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Most of time that MMC driver spends on initializing a device is polling
OCR (operation conditions register). To decouple this polling loop,
device init is split into two parts: The first part fires the OCR query
command, and the second part polls the result. So the caller is now no
longer bound to the OCR-polling delay; he may fire the query, go
somewhere and then come back later for the result.
To use this, call mmc_set_preinit() on any device which needs this.
This can save significant amounts of time on boot (e.g. 200ms) by
hiding the MMC init time behind other init.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We can use a common global method for calculating minimum of
3 numbers. Put the same in 'common header' and let 'ehci'
use it.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Fix the Port status bit constants and Port feature number
constants as a part of USB 2.0 and USB 3.0 Hub class.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Untill now we power-cycle (aka: disable power on a port
and re-enabling again) one port at a time.
Delay of 20ms for Port-power to change multiplies with
number of ports in this case.
So better we parallelize this process:
disable power on all ports, wait for port-power to stabilize
and then re-enable the power subsequently.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
This adds usb framework support for super-speed usb, which will
further facilitate to add stack support for xHCI.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Patch b6d7852c increases timeout for enumeration, taking
worst case to be 10 sec.
get_timer() api returns timestamp in milliseconds, which is
what we are checking in the do-while() loop in usb_hub_configure()
(get_timer(start) < CONFIG_SYS_HZ * 10).
This should give us a required check for 10 seconds, and thereby
we don't need to add additional mdelay of 100 microseconds in
each cycle.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Fetch the device class into usb device's dwcriptors,
so that the host controller's driver can use this info
to differentiate between HUB and DEVICE.
Signed-off-by: Amar <amarendra.xt@samsung.com>
XHCI ports are powered on after a H/W reset, however
EHCI ports are not. So disabling and re-enabling power
on all ports invariably.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Some cleanup in usb framework, nothing much on feature side.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
USB_PRINTF, USB_HUB_PRINTF, USB_STOR_PRINTF, USB_KBD_PRINTF
are nothing but conditional debug prints, depending on DEBUG.
So better remove them and use debug() simply.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
This patch adds a new 'usb test' command, that will set a port to a USB
2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes
on both downstream hub ports and ordinary device's upstream ports. In
addition, it supports EHCI root hub ports.
Signed-off-by: Julius Werner <jwerner@chromium.org>
With the u-boot-with-spl.bin rule calling $(OBJCOPY) with
CONFIG_SPL_PAD_TO, and CONFIG_SPL_PAD_TO defaulting to
CONFIG_SPL_MAX_SIZE we cannot use math here, so set it to 4096 rather
than 4 * 1024.
Signed-off-by: Tom Rini <trini@ti.com>
The Hydra and Superhydra (P3041DS, P5020DS, and P5040DS) boards have a
second USB port that can be configured in either host, peripheral (aka
device), or OTG (on-the-go) mode. When configured in host mode, if
the port is connected to another USB host, damage to the board can
occur.
To avoid this, we change the default setting to peripheral mode. Ideally,
we'd set it to OTG mode, but currently there is no OTG support for
these boards.
Setting the hwconfig variable will also update the device tree, and so
Linux will configure the port for peripheral mode as well.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When P1021RDB-PC reboot system, the board will hung at uboot DDR
configuration. For P1021RDB-PC DDR reset pin is multiplex with
QE, so uboot will reserve this pin for QE and skip DDR reset.
Other platforms without QE will do this reset. This patch adds
a slight code to reset DDR chip by QE CE_PB8 pin for NAND and
NOR FLASH boot. For booting from SPI FALSH and SD card, it
seems possible to use the rom on chip to write to the GPIO
pins before configuring the DDR.
Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Extending LIODN offset range from 1-5 to 1-10
While using a qman portal with a higher index the LIODN offset
is incorrectly set, thus extending the range of offsets covers
all 10 qman portals
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Acked-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum DDR_A003 applies to P5020, P3041, P4080, P3060, P2041, P5040.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Change flexcan compatible string from "fsl,flexcan-v1.0"
to "fsl,p1010-flexcan" to match the device tree.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Only some chips have four SerDes banks, so don't define lanes for a bank
that doesn't exist.
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Resolve P1020 second USB controller multiplexing with eLBC
- mandatory to mention USB2 in hwconfig string to select it
over eLBC, otherwise USB2 node is removed
- works only for SPI and SD boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There could be scenarios where the user would like to manually(via JTAG)
configure the DDR/L2SRAM and load the bootloader binary onto DDR/L2SRAM.
This document explains thse usecases and the detailed explanation of what needs
to be done to use it.
Most of the code from CONFIG_SYS_RAMBOOT will be used except for small changes
of CCSRBAR etc.
The changes are not very large, but it is good to document them so that user
can get it working at once.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
As per Errata list of BSC9131 and BSC9132, IFC Errata A003399 is no more
valid. So donot compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Simon Glass
Gerald Van Baren
Justin Sobota
François Revol
Tom Rini
Stefan Kristiansson
Egbert Eich
Anatolij Gustschin
Michal Simek
Lucian Cojocar
Marek Vasut
Kuan-Yu Kuo
Fabio Estevam
Jaehoon Chung
Vipin Kumar
Davide Bonfanti
Che-Liang Chiou
Vivek Gautam
Bo Shen
Julius Werner
Jim Lin
Shaohui Xie
Xu Jiucheng
Cristian Sovaiala
York Sun
Shengzhou Liu
Timur Tabi
Zhicheng Fan
Poonam Aggrwal
Prabhakar Kushwaha