|
|
|
/*
|
|
|
|
* (C) Copyright 2000-2008
|
|
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
|
|
*
|
|
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
|
|
*/
|
|
|
|
|
|
|
|
/*
|
|
|
|
* board/config.h - configuration options, board specific
|
|
|
|
*/
|
|
|
|
|
|
|
|
#ifndef __CONFIG_H
|
|
|
|
#define __CONFIG_H
|
|
|
|
|
|
|
|
/*
|
|
|
|
* High Level Configuration Options
|
|
|
|
* (easy to change)
|
|
|
|
*/
|
|
|
|
|
|
|
|
#define CONFIG_MPC855 1 /* This is a MPC855 CPU */
|
|
|
|
#define CONFIG_TQM855L 1 /* ...on a TQM8xxL module */
|
|
|
|
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0x40000000
|
|
|
|
|
|
|
|
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
|
|
|
|
#define CONFIG_SYS_SMC_RXBUFLEN 128
|
|
|
|
#define CONFIG_SYS_MAXIDLE 10
|
|
|
|
#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
|
|
|
|
|
|
|
|
#define CONFIG_BOOTCOUNT_LIMIT
|
|
|
|
|
|
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
|
|
|
|
|
|
#define CONFIG_BOARD_TYPES 1 /* support board types */
|
|
|
|
|
|
|
|
#define CONFIG_PREBOOT "echo;" \
|
|
|
|
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
|
|
|
|
"echo"
|
|
|
|
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
|
|
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
|
|
"netdev=eth0\0" \
|
|
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
|
|
"addip=setenv bootargs ${bootargs} " \
|
|
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
|
|
|
":${hostname}:${netdev}:off panic=1\0" \
|
|
|
|
"flash_nfs=run nfsargs addip;" \
|
|
|
|
"bootm ${kernel_addr}\0" \
|
|
|
|
"flash_self=run ramargs addip;" \
|
|
|
|
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
|
|
|
|
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
|
|
|
|
"rootpath=/opt/eldk/ppc_8xx\0" \
|
|
|
|
"hostname=TQM855L\0" \
|
|
|
|
"bootfile=TQM855L/uImage\0" \
|
|
|
|
"fdt_addr=40040000\0" \
|
|
|
|
"kernel_addr=40060000\0" \
|
|
|
|
"ramdisk_addr=40200000\0" \
|
|
|
|
"u-boot=TQM855L/u-image.bin\0" \
|
|
|
|
"load=tftp 200000 ${u-boot}\0" \
|
|
|
|
"update=prot off 40000000 +${filesize};" \
|
|
|
|
"era 40000000 +${filesize};" \
|
|
|
|
"cp.b 200000 40000000 ${filesize};" \
|
|
|
|
"sete filesize;save\0" \
|
|
|
|
""
|
|
|
|
#define CONFIG_BOOTCOMMAND "run flash_self"
|
|
|
|
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
|
|
|
|
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
|
|
|
|
#define CONFIG_STATUS_LED 1 /* Status LED enabled */
|
|
|
|
|
|
|
|
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
|
|
|
|
|
|
|
|
/*
|
|
|
|
* BOOTP options
|
|
|
|
*/
|
|
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
|
|
|
|
|
|
|
|
#define CONFIG_MAC_PARTITION
|
|
|
|
#define CONFIG_DOS_PARTITION
|
|
|
|
|
|
|
|
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
|
|
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Command line configuration.
|
|
|
|
*/
|
|
|
|
#include <config_cmd_default.h>
|
|
|
|
|
|
|
|
#define CONFIG_CMD_ASKENV
|
|
|
|
#define CONFIG_CMD_DATE
|
|
|
|
#define CONFIG_CMD_DHCP
|
|
|
|
#define CONFIG_CMD_ELF
|
|
|
|
#define CONFIG_CMD_EXT2
|
|
|
|
#define CONFIG_CMD_IDE
|
|
|
|
#define CONFIG_CMD_JFFS2
|
|
|
|
#define CONFIG_CMD_NFS
|
|
|
|
#define CONFIG_CMD_SNTP
|
|
|
|
|
|
|
|
|
|
|
|
#define CONFIG_NETCONSOLE
|
|
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Miscellaneous configurable options
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
|
|
|
|
|
|
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
|
|
|
|
#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
|
|
|
|
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
|
|
#else
|
|
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
|
|
#endif
|
|
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Low Level Configuration Settings
|
|
|
|
* (address mappings, register initial values, etc.)
|
|
|
|
* You should know what you are doing if you make changes here.
|
|
|
|
*/
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* Internal Memory Mapped Register
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_IMMR 0xFFF00000
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* Start addresses for the final memory configuration
|
|
|
|
* (Set up by the startup code)
|
|
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
|
|
#define CONFIG_SYS_FLASH_BASE 0x40000000
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
|
|
|
|
|
|
/*
|
|
|
|
* For booting Linux, the board info and command line data
|
|
|
|
* have to be in the first 8 MB of memory, since this is
|
|
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* FLASH organization
|
|
|
|
*/
|
|
|
|
|
|
|
|
/* use CFI flash driver */
|
|
|
|
#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
|
|
|
|
#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
|
|
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE+flash_info[0].size }
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
|
|
|
|
|
|
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
|
|
#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
|
|
|
|
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
|
|
|
|
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
|
|
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
|
|
|
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
|
|
|
|
|
|
|
|
#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
|
TQM8xx[LM]: Fix broken environment alignment.
With recent toolchains, the environment sectors were no longer aligned to
sector boundaries. The reason was a combination of two bugs:
1) common/environment.c assumed that CONFIG_TQM8xxL would be defined
for all TQM8xxL and TQM8xxM boards. But "include/common.h", where
this gets defined, is not included here (and cannot be included
without causing lots of problems).
Added a new #define CFG_USE_PPCENV for all boards which really
want to put the environment is a ".ppcenv" section.
2) The linker scripts just include environment.o, silently assuming
that the objects in that file are really in the order in which
they are coded in the C file, i. e. "environment" first, then
"redundand_environment", and "env_size" last. However, current
toolchains (GCC-4.x) reorder the objects, causing the environment
data not to start on a flash sector boundary:
Instead of: we got:
40008000 T environment 40008000 T env_size
4000c000 T redundand_environment 40008004 T redundand_environment
40010000 T env_size 4000c004 T environment
Note: this patch fixes just the first part, and cures the alignment
problem by making sure that "env_size" gets placed correctly. However,
we still have a potential issue because primary and redundant
environment sectors are actually swapped, i. e. we have now:
40008000 T redundand_environment
4000c000 T environment
40010000 T env_size
This shall be fixed in the next version.
Signed-off-by: Wolfgang Denk <wd@denx.de>
18 years ago
|
|
|
|
|
|
|
#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* Dynamic MTD partition support
|
|
|
|
*/
|
|
|
|
#define CONFIG_CMD_MTDPARTS
|
|
|
|
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
|
|
|
|
#define CONFIG_FLASH_CFI_MTD
|
|
|
|
#define MTDIDS_DEFAULT "nor0=TQM8xxL-0"
|
|
|
|
|
|
|
|
#define MTDPARTS_DEFAULT "mtdparts=TQM8xxL-0:256k(u-boot)," \
|
|
|
|
"128k(dtb)," \
|
|
|
|
"1664k(kernel)," \
|
|
|
|
"2m(rootfs)," \
|
|
|
|
"4m(data)"
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* Hardware Information Block
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
|
|
|
|
#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
|
|
|
|
#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* Cache Configuration
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
|
|
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
|
|
|
|
#endif
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* SYPCR - System Protection Control 11-9
|
|
|
|
* SYPCR can only be written once after reset!
|
|
|
|
*-----------------------------------------------------------------------
|
|
|
|
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
|
|
|
|
*/
|
|
|
|
#if defined(CONFIG_WATCHDOG)
|
|
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
|
|
|
|
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
|
|
|
|
#else
|
|
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
|
|
|
|
#endif
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* SIUMCR - SIU Module Configuration 11-6
|
|
|
|
*-----------------------------------------------------------------------
|
|
|
|
* PCMCIA config., multi-function pin tri-state
|
|
|
|
*/
|
|
|
|
#ifndef CONFIG_CAN_DRIVER
|
|
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
|
|
|
|
#else /* we must activate GPL5 in the SIUMCR for CAN */
|
|
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
|
|
|
|
#endif /* CONFIG_CAN_DRIVER */
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* TBSCR - Time Base Status and Control 11-26
|
|
|
|
*-----------------------------------------------------------------------
|
|
|
|
* Clear Reference Interrupt Status, Timebase freezing enabled
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* RTCSC - Real-Time Clock Status and Control Register 11-27
|
|
|
|
*-----------------------------------------------------------------------
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* PISCR - Periodic Interrupt Status and Control 11-31
|
|
|
|
*-----------------------------------------------------------------------
|
|
|
|
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
|
|
|
|
*-----------------------------------------------------------------------
|
|
|
|
* Reset PLL lock status sticky bit, timer expired status bit and timer
|
|
|
|
* interrupt status bit
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* SCCR - System Clock and reset Control Register 15-27
|
|
|
|
*-----------------------------------------------------------------------
|
|
|
|
* Set clock output, timebase and RTC source and divider,
|
|
|
|
* power management and some other internal clocks
|
|
|
|
*/
|
|
|
|
#define SCCR_MASK SCCR_EBDF11
|
|
|
|
#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
|
|
|
|
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
|
|
|
|
SCCR_DFALCD00)
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* PCMCIA stuff
|
|
|
|
*-----------------------------------------------------------------------
|
|
|
|
*
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
|
|
|
|
#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
|
|
|
|
#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
|
|
|
|
#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
|
|
|
|
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
|
|
|
|
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
|
|
|
|
#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
|
|
|
|
#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
|
|
|
|
*-----------------------------------------------------------------------
|
|
|
|
*/
|
|
|
|
|
|
|
|
#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
|
|
|
|
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
|
|
|
|
|
|
|
|
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
|
|
|
|
#undef CONFIG_IDE_LED /* LED for ide not supported */
|
|
|
|
#undef CONFIG_IDE_RESET /* reset for ide not supported */
|
|
|
|
|
|
|
|
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
|
|
|
|
#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
|
|
|
|
|
|
|
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
|
|
|
|
|
|
|
#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
|
|
|
|
|
|
|
|
/* Offset for data I/O */
|
|
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
|
|
|
|
|
|
|
|
/* Offset for normal register accesses */
|
|
|
|
#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
|
|
|
|
|
|
|
|
/* Offset for alternate registers */
|
|
|
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
|
|
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
|
|
*
|
|
|
|
*-----------------------------------------------------------------------
|
|
|
|
*
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_DER 0
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Init Memory Controller:
|
|
|
|
*
|
|
|
|
* BR0/1 and OR0/1 (FLASH)
|
|
|
|
*/
|
|
|
|
|
|
|
|
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
|
|
|
|
#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
|
|
|
|
|
|
|
|
/* used to re-map FLASH both when starting from SRAM or FLASH:
|
|
|
|
* restrict access enough to keep SRAM working (if any)
|
|
|
|
* but not too much to meddle with FLASH accesses
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
|
|
|
|
#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
|
|
|
|
|
|
|
|
/*
|
|
|
|
* FLASH timing:
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
|
|
|
|
OR_SCY_3_CLK | OR_EHTR | OR_BI)
|
|
|
|
|
|
|
|
#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
|
|
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
|
|
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
|
|
|
|
|
|
|
|
#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
|
|
|
|
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
|
|
|
|
#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
|
|
|
|
|
|
|
|
/*
|
|
|
|
* BR2/3 and OR2/3 (SDRAM)
|
|
|
|
*
|
|
|
|
*/
|
|
|
|
#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
|
|
|
|
#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
|
|
|
|
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
|
|
|
|
|
|
|
|
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
|
|
|
|
#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
|
|
|
|
|
|
|
|
#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
|
|
|
|
#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
|
|
|
|
|
|
|
|
#ifndef CONFIG_CAN_DRIVER
|
|
|
|
#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
|
|
|
|
#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
|
|
|
|
#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
|
|
|
|
#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
|
|
|
|
#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
|
|
|
|
#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
|
|
|
|
#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
|
|
|
|
BR_PS_8 | BR_MS_UPMB | BR_V )
|
|
|
|
#endif /* CONFIG_CAN_DRIVER */
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Memory Periodic Timer Prescaler
|
|
|
|
*
|
|
|
|
* The Divider for PTA (refresh timer) configuration is based on an
|
|
|
|
* example SDRAM configuration (64 MBit, one bank). The adjustment to
|
|
|
|
* the number of chip selects (NCS) and the actually needed refresh
|
|
|
|
* rate is done by setting MPTPR.
|
|
|
|
*
|
|
|
|
* PTA is calculated from
|
|
|
|
* PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
|
|
|
|
*
|
|
|
|
* gclk CPU clock (not bus clock!)
|
|
|
|
* Trefresh Refresh cycle * 4 (four word bursts used)
|
|
|
|
*
|
|
|
|
* 4096 Rows from SDRAM example configuration
|
|
|
|
* 1000 factor s -> ms
|
|
|
|
* 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
|
|
|
|
* 4 Number of refresh cycles per period
|
|
|
|
* 64 Refresh cycle in ms per number of rows
|
|
|
|
* --------------------------------------------
|
|
|
|
* Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
|
|
|
|
*
|
|
|
|
* 50 MHz => 50.000.000 / Divider = 98
|
|
|
|
* 66 Mhz => 66.000.000 / Divider = 129
|
|
|
|
* 80 Mhz => 80.000.000 / Divider = 156
|
|
|
|
*/
|
|
|
|
|
|
|
|
#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
|
|
|
|
#define CONFIG_SYS_MAMR_PTA 98
|
|
|
|
|
|
|
|
/*
|
|
|
|
* For 16 MBit, refresh rates could be 31.3 us
|
|
|
|
* (= 64 ms / 2K = 125 / quad bursts).
|
|
|
|
* For a simpler initialization, 15.6 us is used instead.
|
|
|
|
*
|
|
|
|
* #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
|
|
|
|
* #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
|
|
|
|
*/
|
|
|
|
#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
|
|
|
|
#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
|
|
|
|
|
|
|
|
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
|
|
|
|
#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
|
|
|
|
#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
|
|
|
|
|
|
|
|
/*
|
|
|
|
* MAMR settings for SDRAM
|
|
|
|
*/
|
|
|
|
|
|
|
|
/* 8 column SDRAM */
|
|
|
|
#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
|
|
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
|
|
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
|
|
/* 9 column SDRAM */
|
|
|
|
#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
|
|
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
|
|
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
|
|
|
|
|
|
#define CONFIG_SCC1_ENET
|
|
|
|
#define CONFIG_FEC_ENET
|
|
|
|
#define CONFIG_ETHPRIME "SCC"
|
|
|
|
|
|
|
|
/* pass open firmware flat tree */
|
|
|
|
#define CONFIG_OF_LIBFDT 1
|
|
|
|
#define CONFIG_OF_BOARD_SETUP 1
|
|
|
|
#define CONFIG_HWCONFIG 1
|
|
|
|
|
|
|
|
#endif /* __CONFIG_H */
|